Serial Port, Status | Agilent Technologies 8935 series e6380a

Configuration - Screens and Control Fields

Control Fields on the Configuration Screens

Serial Port

This field selects the serial port. The SERIAL 9 port must be used for serial printing. SERIAL 11 is reserved for use with special software that enables remote operation through a PC.

For more information about the serial ports see “SERIAL 9, 10, and 11” on page 291.

Screen(s) Where Field is Present

I/O CONFIGURE

MODEM CONFIGURE

Status

This field indicates the status of the modem connection.

•Connected

•Idle

•Waiting

•Dialing

•Authenticating

•Disconnecting

Screen(s) Where Field is Present

MODEM CONFIGURE

Stop Length

This field specifies the number of stop bits (1 or 2) used for serial communications when using the serial port.

This setting is maintained after the instrument is turned off.

Operating Considerations

When in remote mode (Remote Mode field is set to On), this field is inaccessible.

Screen(s) Where Field is Present

I/O CONFIGURE

Chapter 7

249

Image 245

Agilent Technologies 8935 series e6380a manual Serial Port, Status, Stop Length

Contents

Revision F January Agilent Part Number E6380-90019Page Contents Overview of the Test Set’s Built-In Tools Cdma Measurements Screens and Control Fields Analog Measurements Screens and Control Fields Contents Contents Control Fields on the Configuration Screens 227 Configuration Screens and Control Fields AMPS-TACS, NAMPS-NTACS Encoder and Decoder 253 Signaling Encoder and Decoder Screens and Control Fields Connectors Connectors Error Messages Accessories, Manuals, Support General Information Herstellerbescheinigung Manufacturers Declaration Safety Considerations Adjustments described in the manual are performed with Connected to the earth terminal of the power sourceInstrument must be made inoperative and be secured against Any unintended operation Protective earthing ground incorporated in the power cord This product is a Safety Class I instrument provided with aMains plug shall only be inserted in a socket outlet Provided with a protective earth contact. Any interruption Consumables Lifting and Handling Product Markings Certification Declaration of Conformity Like-new Defects in material and workmanship when properly installedIts programming instructions due to such defects Price upon prompt return of the product Chapter Assistance Regional Sales and Service Office s Straight/90 8120-1692 Inches, mint gray Power CablesPower Cables Used in the following locations Peru Used in the following locations Switzerland Straight/90 8120-4754 Inches, dark gray JIS C 8303, 100 90 /Straight 8120-1351 Inches, mint gray LineNeutral Straight/90 Used in the following locations System Cabinets 8120-4379 Inches, jade gray Power Cables Product Description Sinad SNR Conventions Used in This Manual What is in This ManualDocumentation Document Part Number Usage Which Document is Required?Document Navigation Trademark Acknowledgments Getting Started Before Connecting a Radio on Before Connecting a Radio Changing the Test Set’s Display Using the cursor-control Knob or Screen Keys To change the measurement screen To change a unit-of-measure field Changing the Control FieldsUnit-of-Measure Field To Change an underlined entry Underlined Entry Field To make a one-of-many choice One-of-Many Field To change a value Numeric-Entry FieldsNumeric-Entry Field Hexadecimal Values Decimal Values How do I Verify that the Test Set is Operating Properly? Cdma Spectrum Operating Overview Operating Overview ADC Full Scale ADC FS Displaying Cdma Measurements Magnitude Error, Phase Error Selecting Code Domain Measurements Diagram Transmitter TXPower Frequency Error, FrequencyDisplaying Analog Measurements RF Measurements Displaying AF Measurements Measurement AF Anl In SettingFM Deviation, AM Depth, AC Level SINAD, Distortion, SNR, AF Frequency, DC Level Displaying SINAD, Distortion, SNR, DC Level, or AF Frequency To set the meter’s end points and scale intervals Displaying Measurement Results on a Meter ScaleTo display the meter scale Operating Overview Calibrating the Channel Power Measurement Cdma Analyzer Calibrating the Channel Power Measurement Code Domain Calibrating the Adjacent Channel Power ACP Measurement Specifying An Increment Value for the Arrow Keys or Knob Changing the Increment or Decrement SettingUsing the Factor of 10 Increment/Decrement Keys To set high and low limits Using Measurement Limit IndicatorsTo reset or remove limits To remove a limit To set a reference Setting a Measurement Reference How the Test Set Averages Measurements Averaging MeasurementsTo use measurement averaging To set an RF Offset Setting an RF Generator/Analyzer Offset To save an instrument setup Saving and Recalling Instrument SetupsTo recall an instrument setup Press Recall To remove clear an individual save register Poweron SettingsTo clear all save registers Register Names Instrument Hardware Changes Base SettingsMemory Considerations Using Pre-Defined User Keys Using User Keys To assign local user keys Assigning and Releasing User KeysTo release local user keys To assign global user keys Replacing Batteries Overview of the Test Set’s Overview of theTest Set’s Built-In Tools Using the RF Tools Program Software Menu Screen Loading and Running RF Tools Test Results/BTS Utility Setup Screens Test Results/BTS Utility Setup To use a printer for data collection To use a laptop interface other than the BTS Laptop Utility Swept GainMeasurement Description Making the Measurement Selecting the Swept Gain Measurement Test Press k1 Begin Tst Level value to avoid damage to that deviceLevel for the Duplex OUT level in dBm parameter Example of a Swept Gain Plot Screen Discrete Frequency Insertion Loss Specifications Second display is enlarged for easier reading Press k1 Proceed when you are finished with this screen.Particular test 10 Selecting the Swept Insertion Loss Measurement Swept Insertion Loss 11 Swept Insertion Loss Setups Estimating Swept Insertion Loss Using a Single Connection Swept Return Loss Select Main Menu Swept Return Loss 13 Swept Return Loss Setups Power level. To avoid damage to the ANT in port, enter an 14 Example of a Swept Return Loss Plot Screen Specifications Test Signal Can Cause Interference Cable FaultTime domain can be used to find the physical distances. Locations by viewing it in units of distance Select Main Menu Cable Fault Measurement Cable length, enter a value 1.5 times the estimated length Greatest accuracy is obtained when you enter a cable lengthToggles the selection between feet and meters K1 HELIAX, k3 RG, or k5 Custom 17 Cable Fault Setups 18 Example of a Cable Fault Plot Screen Replot Data Files Typical cable fault return loss measurementsCable Fault Performance Select Main Menu 21 Transfer Stored Data Screen Transfer Stored Data 22 SA Self Calibration OFF/ON Screen SA Spectrum Analyzer Self Calibration ON/OFF Catalog PC Memory Card 23 Catalog Memory Card Screen Selecting the Code Domain Analyzer’s Controls Menus Using the Code Domain Analyzer 24 Code Domain Analyzer Menus IS-95 25 Code Domain Analyzer Menus IS-2000 Setting Resolution Bandwidth and Sweep Rate Using the Spectrum AnalyzerRelationship between Span, Resolution Bandwidth, and Sweep Automatic Calibration 26 Spectrum Analyzer Controls Menus Selecting the Spectrum Analyzer’s Controls Menus Delta Level Using the Spectrum Analyzer’s Delta MarkersDelta Frequency Reference Marker Ref Mrkr Level and Frequency Displaying the Spectrum Analyzer Mask Using the Spectrum Analyzer Mask Defining the Fixed Mask’s Limits Settings for mask in FigurePoint Point Level Frequency Turning Off the Mask’s Failure Beeper Defining the Relative Mask’s LimitsTurning Off the Mask Set to Audio Using the Voltmeter and Audio Frequency CounterMeasuring AC and DC Voltages AC Level Set to DC Level or AF Freq Set to match source 29 Inputs and Filters for the Oscilloscope Using the Oscilloscope Scope Selecting the Oscilloscope’s Input Triggering the Oscilloscope Using the Oscilloscope’s MarkerSelecting the Oscilloscope’s Filters Copypl Using Ibutil Programs Securing aTest Procedure Clearing RAM Using the Listopts list options Program Using the Demo Program Step Using the Stplt store or plot Program Cdma Measurements Screens and Control Fields 130 Cdma Measurements Average Power MeasurementsAvg Pwr Screens on which this measurement is displayed Channel Power Measurements Adjacent Channel Power MeasurementsScreens on which this measurement is made Chan Pwr Rho Rho Measurements Code DOM Code Domain Analyzer Frequency Error Freq ErrEstimated Rho Est Rho Time Offset Carrier Feedthrough Chapter 137 Phase Error Error Vector Magnitude EVM MeasurementsMagnitude Error Code Domain Measurements IS-95 Code Domain Power, IS-95 Code DOM Code Domain Analyzer, IS-95 only Selecting Absolute or Relative Code Domain Power, IS-95 only Code Domain Timing Timing Fast PowerCode Domain Phase Phse Code Domain Measurements IS-2000 Advantages of Using IS-2000 Interpreting IS-2000 Channel Ordering Building a tree using the Bit Reverse method Channel numbers. The Walsh index utilizes Walsh orders 0 Available Measurements in the Code Domain 11 Code Domain Power, Bit Reverse Ordering Reading Code Domain Power, IS-2000 Code Domain Power, IS-2000 Code DOM Code Domain Analyzer, IS-2000 Code Domain Power & Noise Code Domain Fast Power Synchronize Code Domain Complex Power PN Offset Search IQ Constellation Diagram, IS-2000 only # of Frames Control Fields for Cdma MeasurementsACP Cal ACP Fltr BW ADCfs or ADC FS ACP OffsetAmplitude Code DOM Code Domain Analyze screen gain controls menu Analyzer code domain analyzer Analyzer Cdma analyzerAnl Dir COD DOM Code Domain Analyzer main controls menu Auto Zero Anl SpecialCarrier FT or Carrier Feedthru Chan Num Chn Pwr Cal Chan SizeCD pwr unit COD DOM Code Domain Analyzer all menus ControlsCW RF Path Data Rate Data Source Freq Err Even SecFind PN COD DOM Code Domain Analyzer gain controls menu GainGen Dir Gen Special Gen Mode Input Port Input AttenLvl Code DOM Code Domain Analyzer gain controls menu Marker Lvl Power LevelMarker Pos Meas Intvl or Meas Int Meas Order COD DOM Code Domain Analyzer fast power setup controls menuMeasurement Num Avgs COD DOM Code Domain Analyzer FP setup controls menu Phase/divOfs Trnsfer Output Port PN Offset PhsePN Incrment Pwr Gain PN Offset or PN Ofs Pwr Ref Pwr IntvlPwr Scale IS-95 Pwr Scale IS-2000 Qual Event Pwr Zero Rate RC-4 Rate RC-3Rate RC-5 Code DOM Code Domain Analyzer trigger controls menu RF Gen Freq RF ChannelRF In/Ant Screens on which this field is displayed Threshold Sprd Fact Spread FactorStart Frame Time/div Time Time Ofs Time Offset Tune Freq Trig Event Walsh Order Walsh Chan Control Fields 178 AM Depth Measurement Analog MeasurementsAC Control DC Level Measurement AF Freq Measurement FM Deviation Measurement Distn Distortion Measurement Frequency Measurement Frequency Error Measurement TX Power Measurement SNR Measurement Is signal to noise ratio of the audio input signalSinad Measurement Control Fields for Analog Measurements Signaling Decoder All Modes#Pts AF Anl AFGen1 Freq AF Cnt Gate AFGen2 Freq AFGen1 To AFGen2 To Signaling Encoder All Modes Spec ANL RF generator controls menu Atten Hold Audio Out Audio In LoAuto/Norm Scope trigger controls menu Spec ANL main controls menu Center FreqSpec ANL all menus except mask controls DC FM Zero Cont/SingleDe-Emp Gain De-Emphasis Detector Types DetectorDisplay EditPt Edit Mask Filter Ext Load RExt TTL FM Coupling Reference Marker Frequency Level Delta Marker Freq Delta MrkrFreq mask Freq normal marker Spec ANL all menus when in normal mode except mask controlsFreq Ref Mrkr Normal Marker Frequency Level If Filter Gain Cntl Spec ANL auxiliary controls menu Input Gain Internal Lvl Delta Mrkr Level divLevel mask Scope all control menus Lvl markerLvl normal marker Marker To Peak+ Lvl Ref MrkrMarker To Peak Scope marker controls menu Mask Beep Marker ToMask Type Spec ANL marker controls menu No Pk/Avg Mod In To Norm/Delta Normalize Offset Freq Notch FreqNotch Gain Pk Det To Scope marker controls menu Spec ANL marker controls menu Port/SweepPosition Ref Mrkr Pos/NegRef Level Spec ANL RF generator or main controls menu ResetRF Cnt Gate Key or turn the Test Set off and on to reset it Maximum signal levels are printed on the connector panelSpec ANL RF Gen controls menu This field selects the input port for the spectrum analyzer Sensitivity RF analyzer Scope To Settling Sensitivity spectrum analyzer Speaker ALC SpanSpeaker Vol Sets the span of frequencies to be displayed on the screen Squelch This field selects the horizontal sweep time per division Track/FixedTime-per-division is selected from a list of choices Scope main controls menu Resolution Trig-Delay TX Pwr Meas Vert/div TX Pwr Zero Vert Offset Configuration Screens 224 Setting the Date and Time Configuring the InstrumentChanging the Beeper’s Volume Turning Off User Messages To interrupt printing Configuring for Printing a ScreenPrinting a Screen Screens Where Field is Present Control Fields on the Configuration ScreensAbort Print Antenna Beeper Base Freq User Defined Cdma Std CallChan Space User Defined 230 Data Length Command Escape CharacterConnection Time-out Duplex Out DateDisplay User Messages FF at End Ext RefFF at Start Firmware OUT connector InaccessibleFlow Control Frame Clock Output Gen-Anl User Defined Gen-Anl Ibasic Echo Hold-off DelayGpib Adrs Inst Echo Incoming Call SecurityLines/Page Mode Model Modem Configuration Modem Mode Modem Initialization/Configuration Number to Call Notch CouplOpt Cdma TB Parity Printer Adrs PasswordPrinter Port Print Title Range Hold Ref Select Remote Mode RF Chan Std Retries See the RF Chan Std on page 244 for more information RF DisplayRF Gen Volts RF Level Offset RF In/Out Save/Recall RF Offset Serial9 Serial BaudSerial No This field displays the serial number of the Test Set Stop Length Serial PortStatus Total RAM Signaling Encoder and Decoder Decoder’s Signal Source Signaling Encoder and Decoder ScreensDecoder Frequency Measurements Encoder Encoder/Decoder Interaction AMPS-TACS, NAMPS-NTACS Encoder and DecoderControl and Voice Channel Identifiers AMPS-TACS, NAMPS-NTACS Decoder Decoder Mode DifferencesInterpreting Decoded Data Recc and AMPS-TACS RVC Measurements Decoding the Reverse Control Channel Recc Data Measure Field NAMPS-NTACS Reverse Voice Channel Measurements Decoding NAMPS-NTACS Reverse Voice Channel RVC Data Measurement Limits Dtmf Sequence Encoder and Decoder Decoding Considerations Function Generator Encoder and Decoder Delay Control Fields for the Signaling Encoder and DecoderArm Meas Bursts Busy/Idle Signaling Decoder Modes AMPS-TACS, NAMP-NTACChannel Data hex Signaling Encoder Signaling DecoderData Level Data Rate analog DSAT/DST hex Signaling Encoder Modes NAMP-NTACSignaling Decoder Modes NAMP-NTAC Data you enter here Filler Focc Hi Tone FrequencyGate Time De-emphasis Effects on Input Level Input Level Signaling Decoder All Modes Examples of Input Level SettingsLo Tone Measure AMPS-TACS/NAMPS-NTACS Focc Message and Filler Data Format Message Focc Message FVC AMPS-TACS Signaling Encoder Modes AMPS-TACS Message/DST FVC Message FVC NAMPS-TACS Signaling Encoder Modes Dtmf Signaling Decoder Modes Dtmf Signaling Decoder All Modes Signaling Encoder All ModesNum of Bits Off Time Polarity On TimeNormal Operation Inverted Operation Pre-Emp Signaling Encoder Modes DtmfRecc Data hex SAT Freq FVC Send Filler Focc SendSend Dsat FVC Signaling Encoder Modes Func Gen Send ModeSine Units Single/Cont Stop StandardDecoder Operating Considerations Encoder Operating Considerations Stop Dsat FVC Symbol Frequencies HzStop Filler Focc Stop Meas Trig Level Signaling Decoder Modes AMPS-TACS, NAMP-NTAC, Func GenTrigger Pattern bin Twist and Pre-emphasis Interaction TwistExamples of Twist and Pre-emphasis Interaction Example Waveform Connectors Operating Considerations Connectors ANT Audio Audio OUT Data EXT REF EXT Scope Trig Parallel Port Pin Assignments Parallel RF IN/OUT Serial Port Pin Assignments Serial 9, 10,Serial Port Pin Assignments Pin Description Video OUT Accessories, Manuals, Support Modifications Accessories Agilent Technologies AccessoriesExternal Monitor Agilent Technologies Manuals English and Other Options Agilent Technologies Test SoftwareNumber Description Order Description Number 1D5 High Stability Reference Customer Training Support for Your InstrumentGetting Help Agilent Regional Sales and Service Offices Error Messages Positive Numbered Error Messages General Information About Error MessagesExample 11-1 Positive numbered error messages take the form Example 11-2 For example Ibasic Error Messages Negative Numbered Error MessagesExample 11-4 Ibasic error messages take the form Example 11-3 For example Text Only Error Messages Gpib Error MessagesExample Gpib error messages take the form Example Text only error messages take the form Warbles and Beeps Non-Recoverable Firmware ErrorMessage Display 304 Chapter 305 306 Index 308 Index 309 310 Index 311 312 Index 313 314 Index 315 316 Index 317 318 Index 319 320 Index 321 322 Index 323 324