AMD SC1200, SC1201 30. F0BAR0+I/O Offset Gpio Configuration Registers, Gpio Support Registers

32579B	Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
6.4.1.1 GPIO Support Registers
F0 Index 10h, Base Address Register 0 (F0BAR0) points to	ration registers are located. Table 6-29gives the bit formats
the base address of where the GPIO runtime and configu-	of I/O mapped registers accessed through F0BAR0.

Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers

Bit	Description
Offset 00h-03h		GPDO0 — GPIO Data Out 0 Register (R/W)	Reset Value: FFFFFFFFh

31:0

GPIO Data Out. Bits [31:0] of this register correspond to GPIO31-GPIO0 signals, respectively. The value of each bit deter- mines the value driven on the corresponding GPIO signal when its output buffer is enabled. Writing to the bit latches the written data unless the bit is locked by the GPIO Configuration register Lock bit (F0BAR0+I/O Offset 24h[3]). Reading the bit returns the value, regardless of the signal value and configuration.

0:Corresponding GPIO signal is driven to low when output enabled.

1:Corresponding GPIO signal is driven or released to high (according to buffer type and static pull-up selection) when out- put is enabled.

Offset 04h-07h GPDI0 — GPIO Data In 0 Register (RO) Reset Value: FFFFFFFFh

31:0

GPIO Data In. Bits [31:0] of this register correspond to GPIO31-GPIO0 signals, respectively. Reading each bit returns the value of the corresponding GPIO signal, regardless of the signal configuration and the GPDO0 register (F0BAR0+I/O Offset 00h) value.

Writes to this register are ignored.

0:Corresponding GPIO signal level is low.

1:Corresponding GPIO signal level is high.

Offset 08h-0Bh		GPIEN0 — GPIO Interrupt Enable 0 Register (R/W)	Reset Value: 00000000h
31:16	Reserved. Must be set to 0.
15:0	GPIO Power Management Event (PME) Enable. Bits [15:0] correspond to GPIO15-GPIO0 signals, respectively. Each bit
	allows PME generation by the corresponding GPIO signal.

0:Disable PME generation.

1:Enable PME generation.

Notes: 1) All of the enabled GPIO PMEs are always reported at F1BAR1+I/O Offset 10h[3].

2)Any enabled GPIO PME can be selected to generate an SCI or SMI at F1BAR1+I/O Offset 0Ch[0].

If SCI is selected, then the individually selected GPIO PMEs are globally enabled for SCI generation at F1BAR1+I/O Offset 12h[3] and the status is reported at F1BAR1+I/O Offset 10h[3].

If SMI is selected, the individually selected GPIO PMEs generate an SMI and the status is reported at

F1BAR0+I/O Offset 00h/02h[0].

Offset 0Ch-0Fh		GPST0 — GPIO Status 0 Register (R/W1C)	Reset Value: 00000000h
31:16	Reserved. Must be set to 0.
15:0	GPIO Status. Bits [15:0] correspond to GPIO15-GPIO0 signals, respectively. Each bit reports a 1 when hardware detects
	the edge (rising/falling on the GPIO signal) that is programmed in F0BAR0+I/O Offset 24h[5]. If the corresponding bit in
	F0BAR0+I/O Offset 08h is set, this edge generates a PME.

0:No active edge detected since the bit was last cleared.

1:Active edge detected.

Writing 1 to the a Status bit clears it to 0.

This is the third level of SMI status reporting to the second level at F0 Index 87h/F7h[7] and the top level at F1BAR0+I/O Offset 00h/02h[0]. Clearing the third level also clears the second and top levels.

This is the second level of SCI status reporting to the top level at F1BAR1+Offset 10h[3]. The status must be cleared at both the this level and the top level (i.e., the top level is not automatically cleared when a bit in this register is cleared).

224 AMD Geode™ SC1200/SC1201 Processor Data Book