SMI Status and Acpi Registers Function | AMD SC1200, SC1201 instruction

32579B

Core Logic Module - SMI Status and ACPI Registers - Function 1

6.4.2SMI Status and ACPI Registers - Function 1

The register space designated as Function 1 (F1) is used to configure the PCI portion of support hardware for the SMI Status and ACPI Support registers. The bit formats for the PCI Header registers are given in Table 6-32.

Located in the PCI Header registers of F1 are two Base Address Registers (F1BARx) used for pointing to the regis- ter spaces designated for SMI status and ACPI support, described later in this section.

Table 6-32. F1: PCI Header Registers for SMI Status and ACPI Support

Bit	Description

Index 00h-01h		Vendor Identification Register (RO)	Reset Value: 100Bh

Index 02h-03h		Device Identification Register (RO)	Reset Value: 0501h

Index 04h-05h		PCI Command Register (R/W)	Reset Value: 0000h

15:1	Reserved. (Read Only)

0	I/O Space. Allow the Core Logic module to respond to I/O cycles from the PCI bus.
	0:	Disable.
	1:	Enable.
	This bit must be enabled to access I/O offsets through F1BAR0 and F1BAR1 (see F1 Index 10h and 40h).

Index 06h-07h		PCI Status Register (RO)	Reset Value: 0280h

Index 08h		Device Revision ID Register (RO)	Reset Value: 00h

Index 09h-0Bh		PCI Class Code Register (RO)	Reset Value: 068000h

Index 0Ch		PCI Cache Line Size Register (RO)	Reset Value: 00h

Index 0Dh		PCI Latency Timer Register (RO)	Reset Value: 00h

Index 0Eh		PCI Header Type (RO)	Reset Value: 00h

Index 0Fh		PCI BIST Register (RO)	Reset Value: 00h

Index 10h-13h		Base Address Register 0 - F1BAR0 (R/W)	Reset Value: 00000001h

This register allows access to I/O mapped SMI status related registers. Bits [7:0] are read only (0000 0001), indicating a 256-byte I/O address range. Refer to Table 6-33 on page 237 for bit formats and reset values of the SMI status registers.

31:8	SMI Status Base Address.

7:0	Address Range. (Read Only)

Index 14h-2Bh		Reserved	Reset Value: 00h

Index 2Ch-2Dh		Subsystem Vendor ID (RO)	Reset Value: 100Bh

Index 2Eh-2Fh		Subsystem ID (RO)	Reset Value: 0501h

Index 30h-3Fh		Reserved	Reset Value: 00h

Index 40h-43h		Base Address Register 1 - F1BAR1 (R/W)	Reset Value: 00000001h

This register allows access to I/O mapped ACPI related registers. Bits [7:0] are read only (0000 0001), indicating a 256 byte address range. Refer to Table 6-34 on page 247 for bit formats and reset values of the ACPI registers.

Note:	This Base Address register moved from its normal PCI Header Space (F1 Index 14h) to prevent plug and play software from
	relocating it after an FACP table is built.

31:8		ACPI Base Address.

7:1		Address Range. (Read Only)

0		Enable. (Write Only) This bit must be set to 1 to enable access to ACPI Support Registers.

Index 44h-FFh			Reserved	Reset Value: 00h

236	AMD Geode™ SC1200/SC1201 Processor Data Book

Image 236

AMD SC1200, SC1201 SMI Status and Acpi Registers Function, 32. F1 PCI Header Registers for SMI Status and Acpi Support

Contents

Publication ID 32579B AMD Geode SC1200/SC1201 Processor Data Book Advanced Micro Devices, Inc. All rights reserved Contacts Trademarks Contents Electrical Specifications Package SpecificationsCore Logic Module Video Processor Module Power Supply Connections Typical Battery ConfigurationTypical Battery Current Normal Operation Mode ACCESS.bus Data Transaction Multiword DMA Data Transfer Timing Diagram 405 USB Data Signal Rise and Fall Timing Diagram 419USB EOP Width Timing Diagram 420 Fast IR Timing MIR and FIR Diagram 422 424 425426 427 32579B IRCP/SP3 Configuration Register Serial Ports 1 and 2 Configuration RegisterACB1 and ACB2 Configuration Register Parallel Port Configuration Register Banks 0 and 1 Common Control and Status Registers 118 119166 167 Pciusb USB PCI Configuration Register Summary F0BAR0+I/O Offset Gpio Configuration RegistersF2BAR4+I/O Offset IDE Controller Configuration Registers F3 PCI Header Registers for Audio Configuration 384 400402 404 General Description Video ProcessorCore Logic SuperI/O Features General FeaturesGX1 Processor Module Video Processor Module Other Features Core Logic ModuleNand Eeprom SuperI/O Module 32579B Architecture Overview 32579B GX1 ModuleMemory Controller SC1200/SC1201 Processor Memory Controller Registers Width Memory Offset Bits Type Name/Function Reset ValueSC1200/SC1201 Processor Memory Controller Register Summary MCMEMCNTRL2 R/W Bit Description GXBASE+8408h-840Bh Mcbankcfg R/WRsvd Reserved. Write as 0070h Rsvd Reserved. Write as GXBASE+840Ch-840Fh Mcdracc R/W Mcgbaseadd R/WMcdradd R/W Fast-PCI Bus Display1 GX1 Module Interface Video Input Port Clock, Timers, and Reset Logic Reset LogicPower-On Reset System Reset 32579B Signal Definitions 32579B AMD GeodeSC1200/SC1201 Processor USB Jtag Interface Signal Definitions Legend Mnemonic Definition SC1200/SC1201 Configuration BGU481 Ball Assignment Sorted by Ball Number REQ0# GNT0# GPIO7 AFD#/DSTRB# PAR GPIO12 FTRDY# AC1 IDEDATA1 Buffer1 Power Signal Name Ball Buffer Power Signal Name BGU481 Ball Assignment Sorted Alphabetically by Signal Name Signal Name Ball No F30 FC/BE0# D21C11 FC/BE1# B17 MD23 MD24MD25 AC28 MD26 AC29 C24 N13, N14, N18A2, A30, B2, B13 F31 Strap Options Nominal External PU/PD Strap SettingsStrap Options Multiplexing Configuration Two-Signal/Group MultiplexingDefault Alternate Ball No Signal Configuration TFT, CRT, PCI, GPIO, System AC97 Fpci Monitoring ACCESS.busInternal Test Three-Signal/Group Multiplexing Four-Signal/Group Multiplexing Gpio UART2 IDE2 Signal Descriptions Signal Name Ball No Type Description MuxMaximum Core Clock Multiplier. These strap signals Boot ROM is 16 Bits Wide. This strap signal enables Memory Interface Signals Column Address Strobe. RAS#, CAS#, WE# and CKE Video Port Interface Signals 4 CRT/TFT Interface Signals Digital RGB Data to TFT Current Compensation for TV DAC. a 0.1 µF to 1.2 µF TV Interface SignalsSuper Video Chrominance. S-Video chrominance sig ACCESS.bus Interface Signals PCI Bus Interface Signals INTA# INTB#INTC# INTD# AA2 STOP# LOCK#DEVSEL# BHE# PERR# SERR#REQ1# REQ0# Sub-ISA Interface Signals Low Pin Count LPC Bus Interface Signals IDE Interface Signals Universal Serial Bus USB Interface Signals Serial Ports UARTs Interface Signals Parallel Port Interface Signals Fast Infrared IR Port Interface Signals 15 AC97 Audio Interface Signals Power Management Interface SignalsGeneral Purpose Wakeup I/Os. These signals each Serial Bus Synchronization. This bit is asserted to syn Suspend Power Plane Control 1 and 2. Control signal PWRBTN# AH5PWRCNT1 AK6 PWRCNT2 AL7 Gpio Interface Signals Debug Monitoring Interface Signals Jtag Interface SignalsFast-PCI Bus Monitoring Signals. When enabled, this System Management Interrupt. This is the input to Test and Measurement Interface Signals PLL6, PLL5 and PLL2 Bypass. These signals are usedMemory Internal Test Signals. These signals are used Thermal Diode Positive / Negative. These signals are for Power and Ground Connections1 Configuration Block Addresses General Configuration Block Register SummaryGeneral Configuration Block 32579B Width Offset Bits Ball # Internal Test Signals Name Add’l Dependencies Other Signal Add’l DependenciesPMR27 Fpcimon General Configuration Block Ball # IDE Signals CRT, Gpio and TFT Signals Name PP/ACB1/FPCI TFT/VOP Name Add’l Dependencies Ball # Gpio Signals LPC Signals Name Add’l Dependencies 32579BGeneral Configuration Block Reserved General Configuration Block Offset 3Dh Revision Register REV RO Offset 3Eh-3Fh Configuration Base Address Register CBA ROOffset 38h Interrupt Selection Register Intsel R/W Watchdog Timer Functional Description Watchdog Registers Watchdog Interrupt3describes the Watchdog registers Usage Hints High-Resolution Timer High-Resolution Timer RegistersWatchdog Status Register Wdsts R/WC Reset Value 00h Offset 05h-07h Reset Value xxxxxxxxh Tmclksel Timer Clock SelectTmen Timer Interrupt Enable Bit Description Offset 08h-0Bh Clock Generators and PLLs Component Parameters Values Tolerance 1 27 MHz Crystal OscillatorCrystal Oscillator Circuit Components 2 GX1 Module Core Clock Internal Fast-PCI ClockCore Clock Frequency Strapped Core Clock Frequency Video Processor Clocks SuperI/O ClocksCore Logic Module Clocks Clock generator and PLL registers are described in Table Clock Generator ConfigurationClock Registers 1514 Reserved. Must be set to 111033.3 MHz 66.7 MHz AB1C AB1D AB2C AB2D Outstanding FeaturesISA PC98 and Acpi Compliant Parallel PortSerial Port Serial Port 3 / Infrared IR Communication Port Access SignalsInternal Internal Signals Module Architecture Configuration Structure / Access SIO Configuration OptionsIndex-Data Register Pair LDN Assignments Default Configuration Setup Address Decoding Standard Configuration Registers SIO Control and Configuration RegistersLogical Device Control and Configuration Registers Standard Logical Device Configuration Registers Standard Configuration Registers DMA Channel Select 1 R/W Index F0h-FEh Logical Device Configuration R/W32579BSuperI/O Module SIO Control and Configuration Registers SIO Control and Configuration Register MapIndex Type Name Power Rail Reset Value SID. SIO ID Logical Device Control and Configuration Relevant RTC Configuration Registers RTC Configuration Registers Base Address MSB register Relevant SWC RegistersLDN 01h System Wakeup Control 10. IRCP/SP3 Configuration Register Relevant IRCP/SP3 Registers 12. Serial Ports 1 and 2 Configuration Register Serial Ports 1 and 2 Configuration register11. Relevant Serial Ports 1 and 2 Registers LDN 03h and 08h Serial Ports 1 14. ACB1 and ACB2 Configuration Register LDN 05h and 06h ACCESS.bus Ports 1ACB1 and ACB2 Configuration register 13. Relevant ACB1 and ACB2 Registers 16. Parallel Port Configuration Register 15. Relevant Parallel Port Registers X32I External X32O Battery = 0.1 μF Real-Time Clock RTCBus Interface RTC Clock Generation 17. Crystal Oscillator Circuit Components Signal Parameters External ElementsOscillator Startup External Oscillator Alarms Timekeeping Data FormatDaylight Saving Leap Years Power Supply 18. System Power States 110 Battery-Backed RAMs and RegistersInterrupt Handling RTC Registers 19. RTC Register Map20. RTC Registers Index Type Name Index 05h Hours Alarm Register Hora R/W Index 04h Hours Register HOR R/WCRD is 112 Index Programmable Month Alarm Register Mona R/W Index 0Ch RTC Control Register C CRC ROIndex Programmable Century Register CEN R/W AMD Geode SC1200/SC1201 Processor Data Book 113 21. Divider Chain Control / Test Selection 22. Periodic Interrupt Rate Encoding23. BCD and Binary Formats Parameter BCD Format Binary Format 0Eh 7Fh Battery-backed general-purpose Byte RAM 00h 7Fh Battery-backed general-purpose Byte RAMRTC General-Purpose RAM Map 24. Standard RAM Map 25. Extended RAM Map 26. Time Range Limits for Ceir Protocols System Wakeup Control SWCEvent Detection SWC Registers 27. Banks 0 and 1 Common Control and Status Register MapType Name Value Offset Type Name Value 29. Banks 0 and 1 Common Control and Status Registers 30. Bank 1 Ceir Wakeup Configuration and Control Registers Bit Description Ceir Wakeup Range 1 Registers Bank 1, Offset 0Ah IRWTR1L Register R/WCeir Pulse Change, Range 1, High Limit Ceir Wakeup Range 2 Registers ACCESS.bus Interface Data TransactionsABD ABC AMD Geode SC1200/SC1201 Processor Data Book 121 ABC ACK Acknowledge ACK CycleABD MSB Master Mode Acknowledge After Every Byte RuleArbitration on the Bus Addressing Transfer Formats Sending the Address Byte Master TransmitMaster Receive Master Stop Slave Mode Configuration 32. ACB Registers ACB Registers31. ACB Register Map MASTER. RO Reserved Inten Interrupt Enable Saen Slave Address EnableEN Enable Stop Stop Legacy Functional Blocks Parallel Port33. Parallel Port Register Map for First Level Offset 34. Parallel Port Register Map for Second Level Offset 130 35. Parallel Port Bit Map for First Level Offset36. Parallel Port Bit Map for Second Level Offset Uart Functionality SP1 and SP2 Type Name 38. Bank Selection Encoding 39. Bank 1 Register Map40. Bank 2 Register Map 41. Bank 3 Register Map 42. Bank 0 Bit Map 43. Bank 1 Bit MapRegister Bits Register Bits Offset 134 44. Bank 2 Bit Map45. Bank 3 Bit Map 3.1 IR/SP3 Mode Register Bank Overview 46. Bank 0 Register MapIRCP/SP3 Register and Bit Maps 01h Register Throughout Offset 00h All Banks 47. Bank Selection Encoding 48. Bank 1 Register Map49. Bank 2 Register Map BSR Bits Bank Selected Functionality 52. Bank 5 Register Map 50. Bank 3 Register Map51. Bank 4 Register Map 55. Bank 0 Bit Map 53. Bank 6 Register Map54. Bank 7 Register Map 56. Bank 1 Bit Map 57. Bank 2 Bit Map58. Bank 3 Bit Map 59. Bank 4 Bit Map 62. Bank 7 Bit Map 60. Bank 5 Bit Map61. Bank 6 Bit Map Feature List Config Integrated AudioVideo Processor Interface Low Pin Count LPC Interface Fast-PCI Interface to External PCI Bus Pserial Interface IDE Configuration Registers PIO ModeIDE Controller Video Retrace Interrupt Physical Region Descriptor Format UltraDMA/33 Signal Definitions UltraDMA/33 ModeStop DMARDY# Strobe Ideiordy Universal Serial Bus Sub-ISA Bus InterfaceIOCS0#/IOCS1# Docw Sub-ISA Support of Delayed PCI Transactions Sub-ISA Bus CyclesFast-PCICLK AD310 Read AD310 Write 5.4 I/O Recovery Delays REQ# GNT#FRAME# IRDY# TRDY# STOP# Bale ISA RD#, IOR# Sub-ISA Bus Data Steering AD310 ISA DMASD150 PCI and Sub-ISA Signal Cycle Multiplexing Cycle Multiplexed PCI / Sub-ISA BallsROM Interface PCI FRAME# TRDY#, IRDY# ROMCS#, DOCCS# IOCS0#, IOCS1# PAR DEVSEL#,STOP#DMA Controller DMA Channels DMA Transfer Modes DMA Controller RegistersDMA Transfer Types DMA Priority Programmable Interval Timer DMA Addressing CapabilityDMA Page Registers and Extended Addressing DMA Address Generation PIC Interrupt Mapping Programmable Interrupt ControllerMaster Mapping PIC Interrupt Sequence PIC I/O RegistersPIC Shadow Register PCI Compatible Interrupts Fast Keyboard Gate Address 20 and CPU Reset Keyboard Support7.1 I/O Port 092h System Control 7.2 I/O Port 061h System Control Power Management Logic Wakeup Events Capability Power Management Events Power Planes Control Signals vs Sleep StatesPower Planes vs. Sleep/Global States Power Button Power Button OverrideThermal Monitoring AMD Geode SC1200/SC1201 Processor Data Book 161 Power Management Programming CPU Power ManagementAPM Support Suspend Modulation AMD Geode SC1200/SC1201 Processor Data Book 163 Volt SuspendSave-to-Disk Peripheral Power Management Device Idle Timers and TrapsGeneral Purpose Timers Acpi Timer Register F1BAR0+I/O Power Management SMI Status Reporting RegistersModule Device Power Management Programming Summary Power Management Programming SummaryLocated at F0 Index xxh Unless Otherwise Noted F1BAR0+I/O Gpio Interface Integrated Audio 11. Physical Region Descriptor Format ByteAudio Data Buffer Reserved Size Memory Region Base Address PRD1 PRD2 PRD3 Codec Configuration/Control Registers Codec Command Register12.2 AC97 Codec Interface Codec Gpio Status and Control Registers Trap SMI Enable Register VSA Technology Support HardwareVSA Technology Audio SMI Related Registers Module Core Logic Module IRQ Configuration Registers Internal IRQ Enable RegisterInternal IRQ Control Register LPC Interface 12. Cycle Types Register Descriptions PCI Configuration Space and Access Methods13. PCI Configuration Address Register 0CF8h Ter’s reset values and page references where the bit for Register SummaryCore Logic module. Included in the tables are the regis Mats are found Width Reset Reference F0 Index Bits AMD Geode SC1200/SC1201 Processor Data Book 177 32579BCore Logic Module Register Summary 178 15. F0BAR0 Gpio Support Registers Summary 16. F0BAR1 LPC Support Registers SummaryF0BAR0+ F0BAR1+ 18. F1BAR0 SMI Status Registers Summary F1BAR0+ 19. F1BAR1 Acpi Support Registers Summary F1BAR1+00h-03h Pcnt Processor Control Register 20h PM2CNT PM2 Control Register 00h 21h-FFh Not Used Width Reset Reference F2 Index Bits 182 Width Reset Reference F3 Index Bits 21. F2BAR4 IDE Controller Support Registers Summary22. F3 PCI Header Registers for Audio Support Summary F2BAR4+ Width Reset 23. F3BAR0 Audio Support Registers SummaryF3BAR0+ 184 Width Reset Reference F5 Index Bits 25. F5BAR0 I/O Control Support Registers SummaryF5BAR0+ AMD Geode SC1200/SC1201 Processor Data Book 185 26. Pciusb USB PCI Configuration Register Summary Name Reset ValuePciusb Width Reference Index Bits AMD Geode SC1200/SC1201 Processor Data Book 187 27. Usbbar USB Controller Registers SummaryUSBBAR0 188 28. ISA Legacy I/O Register SummaryDMA Page Registers Table Programmable Interval Timer Registers Table Port Type Name ReferenceProgrammable Interrupt Controller Registers Table Keyboard Controller Registers Table General Remarks Chipset Register SpaceBridge, GPIO, and LPC Registers Function Core Logic Module Bridge, GPIO, and LPC Registers Function Data Parity Detected. This bit is set whenIndex 09h-0Bh AMD Geode SC1200/SC1201 Processor Data Book 191 Index 0Eh PCI Header Type RO Reset Value 80h Slave responseIndex 0Fh PCI Bist Register RO 316 Gpio Base Address PCI Subtractive Decode AMD Geode SC1200/SC1201 Processor Data Book 193 Reset Control Register R/W Reset Value 01h Index 42hIndex 43h 194 Index 45h Index 46hIndex 47h AMD Geode SC1200/SC1201 Processor Data Book 195 Reset Value 7Bh PIT Software ResetPIT Counter 1 Enable PIT Counter 0 Enable AMD Geode SC1200/SC1201 Processor Data Book 197 ROM/AT Logic Control Register R/W Reset Value 98hGenerate SMI on A20M# Toggle Bit Description Index 54h-59h Index 5AhIndex 5Bh Decode Control Register 2 R/W 198 INTB# Ball C26 Target Interrupt INTA# Ball D26 Target InterruptINTD# Ball AA2 Target Interrupt INTC# Ball C9 Target Interrupt 200 150Index 72h Index 73h Index 74h-75hIndex 76h Chip Select 0 Positive Decode IOCS0# Ing the upper 19 bits of the incoming PCI address AD3113 202 AMD Geode SC1200/SC1201 Processor Data Book 203 Power Management Enable Register 2 R/W Reset Value 00hTimer expires Disable Enable 204 Power Management Enable Register 3 R/W Reset Value 00h Keyboard/Mouse Access TrapParallel/Serial Access Trap AMD Geode SC1200/SC1201 Processor Data Book 205 Floppy Disk Access Trap Primary Hard Disk Access TrapIndex 83h Power Management Enable Register 4 R/W 206 Index 84h Second Level PME/SMI Status Mirror Register 1 RO AMD Geode SC1200/SC1201 Processor Data Book 207 208 AMD Geode SC1200/SC1201 Processor Data Book 209 210 Index 88h General Purpose Timer 1 Count Register R/WReserved. Always reads AMD Geode SC1200/SC1201 Processor Data Book 211 Re-trigger General Purpose Timer 1 on Floppy Disk ActivitySecond Millisecond 212 Index 8Bh General Purpose Timer 2 Control Register R/WIndex 8Dh Video Speedup Timer Count Register R/W AMD Geode SC1200/SC1201 Processor Data Book 213 Index 8Fh-92hIndex 93h Index 9Ah-9Bh Floppy Disk Idle Timer Count Register R/W Index 97hIndex 98h-99h 214 Index A6h-A7h Video Idle Timer Count Register R/W Index A8h-A9h Video Overflow Count Register R/W Index AEh CPU Suspend Command Register WO Index AFh Suspend Notebook Command Register WOIndex B0h-B3h Index B4h AMD Geode SC1200/SC1201 Processor Data Book 217 Index B9h PIC Shadow Register ROIndex BAh PIT Shadow Register RO Index BCh Clock Stop Control Register R/W Reset Value 00h Reserved. Set to CPU Clock StopIndex BDh-BFh Index C0h-C3h Bit Description Index CCh MaskIndex CDh Index CEh Index EDh-F3h Index F4hIndex F5h Second Level PME/SMI Status Register 2 RC 220 Index F6h Second Level PME/SMI Status Register 3 RC AMD Geode SC1200/SC1201 Processor Data Book 221 222 Index F7h Second Level PME/SMI Status Register 4 RCReserved. Read as Index F8h-FFh 30. F0BAR0+I/O Offset Gpio Configuration Registers I/O mapped registers accessed through F0BAR0Gpio Support Registers Ration registers are located. -29gives the bit formats Offset 14h-17h GPDI1 Gpio Data In 1 Register RO F0BAR0+I/O Offset 18h is set, this edge generates a PME316 Reserved. Must be set to AMD Geode SC1200/SC1201 Processor Data Book 225 Bank 010010 = GPIO18 ball AG1 000011010011 = GPIO19 ball C9 000100 010100 = GPIO20 balls A9, N31 000101 AMD Geode SC1200/SC1201 Processor Data Book 227 31. F0BAR1+I/O Offset LPC Interface Configuration Registers LPC Support Registers3121 Reserved. Set to AMD Geode SC1200/SC1201 Processor Data Book 229 Polarity selection 230 Reserved Serial IRQ Enable Serial IRQ Interface ModeNumber of IRQ Data Frames AMD Geode SC1200/SC1201 Processor Data Book 231 232 LPC Game Port 1 Address Select. Selects I/O Port LPC Game Port 0 Address Select. Selects I/O PortLPC Floppy Disk Controller Address Select. Selects I/O Port LPC Midi Address Select. Selects I/O Port 234 Bit SMI Status and Acpi Registers Function 32. F1 PCI Header Registers for SMI Status and Acpi Support 33. F1BAR0+I/O Offset SMI Status Registers SMI Status Support RegistersCore Logic Module SMI Status and Acpi Registers Function AMD Geode SC1200/SC1201 Processor Data Book 237 238 Suspend Modulation Enable Mirror. Read to ClearOffset 02h-03h Top Level PME/SMI Status Register RO/RC AMD Geode SC1200/SC1201 Processor Data Book 239 Yes To enable SMI generation, set F0 Index 82h6 = Yes To enable SMI generation, set F0 Index 82h5 =Offset 04h-05h 240 AMD Geode SC1200/SC1201 Processor Data Book 241 242 Offset 0Ah-1BhThese addresses should not be written Offset 1Ch-1Fh AMD Geode SC1200/SC1201 Processor Data Book 243 Offset 24h-27h External SMI Register R/W3124 244 AMD Geode SC1200/SC1201 Processor Data Book 245 246 Offset 28h-4Fh Not Used Reset Value 00h50h-FFh Offset 06h Smicmd OS/BIOS Requests Register R/W 34. F1BAR1+I/O Offset Acpi Support RegistersAcpi Support Registers Clkval Clock Throttling Value. CPU duty cycle SCI generation is always enabled 248 Offset 0Ah-0Bh PM1AEN PM1A PME/SCI Enable Register R/W 1511Offset 0Ch-0Dh PM1ACNT PM1A Control Register R/W 1514 Reserved. Must be set to 250 AMD Geode SC1200/SC1201 Processor Data Book 251 252 Gpwio Control Register 1 R/W Reset Value 00h Gpwio Control Register 2 R/W Reset Value 00h ReservedConsumer Electronic Infrared 02h0 Gpwio Data Register R/W Reset Value 00h Reserved Reset Value 00h 254 Reset Value 00000F00h Bit Description Offset 18h-1BhOffset 21h-FFh AMD Geode SC1200/SC1201 Processor Data Book 255 IDE Controller Registers Function PIOMODE. PIO mode Core Logic Module IDE Controller Registers FunctionBit Description Index 30h-3Fh AMD Geode SC1200/SC1201 Processor Data Book 257 258 Bit Description Index 48h-4Bh Index 50h-53hIndex 58h-5Bh Index 60h-FFh IDE Controller Support Registers 260 Offset 09h Offset 0AhOffset 0Bh Offset 0Ch-0Fh 37. F3 PCI Header Registers for Audio Configuration Audio Registers Function 38. F3BAR0+Memory Offset Audio Configuration Registers Audio Support RegistersCore Logic Module Audio Registers Function Offset 04h-07h 264 AMD Geode SC1200/SC1201 Processor Data Book 265 266 These bits change only on a fast write to an even address2316 AMD Geode SC1200/SC1201 Processor Data Book 267 268 Mask Internal IRQ15. Write Only Mask Internal IRQ14. Write OnlyMask Internal IRQ11. Write Only Mask Internal IRQ10. Write Only Mask Internal IRQ4. Write Only Mask Internal IRQ3. Write OnlyAssert Masked Internal IRQ14 Reserved. Set to Assert Masked Internal IRQ12 Bit Description Assert Masked Internal IRQ1 AMD Geode SC1200/SC1201 Processor Data Book 271 Audio Bus Master 1 Command Register R/W Reset Value 00h Offset 29h Audio Bus Master 1 SMI Status Register RCOffset 2Ah-2Bh Offset 2Ch-2Fh Audio Bus Master 2 Command Register R/W Reset Value 00h Offset 31h Audio Bus Master 2 SMI Status Register RCOffset 32h-33h Offset 34h-37h Audio Bus Master 3 Command Register R/W Reset Value 00h Offset 39h Audio Bus Master 3 SMI Status Register RCOffset 3Ah-3Bh Offset 3Ch-3Fh Audio Bus Master 4 Command Register R/W Reset Value 00h Offset 41h Audio Bus Master 4 SMI Status Register RCOffset 42h-43h Offset 44h-47h Audio Bus Master 5 Command Register R/W Reset Value 00h Offset 49h Audio Bus Master 5 SMI Status Register RCOffset 4Ah-4Bh Offset 4Ch-4Fh Bus Expansion Interface Function 39. F5 PCI Header Registers for X-Bus Expansion Bit Description Index 1Ch-1Fh Index 20h-23hIndex 24h-27h Index 28h-2Bh Index 58h F5BARx Initialized Register R/W Reset Value 00h Index 48h-4Bh F5BAR2 Mask Address Register R/WIndex 4Ch-4Fh F5BAR3 Mask Address Register R/W Index 50h-53h F5BAR4 Mask Address Register R/W 280 Bit Description Index 64h-67hIndex 68h-FFh F5 Index 10h, Base Address Register 0 F5BAR0 set 40. F5BAR0+I/O Offset X-Bus Expansion RegistersBus Expansion Support Registers Three USB transceivers. Default = 128 USB transceivers. Default =Iotestporten Debug Test Port Enable 282 41. Pciusb USB PCI Configuration Registers USB Controller Registers PciusbCore Logic Module USB Controller Registers Pciusb AMD Geode SC1200/SC1201 Processor Data Book 283 Reset Value 08h Index 0Dh Latency Timer Register R/WBit Description Index 06h-07h Status Register R/W Reserved. Must be set to Index 08h 42. USBBAR+Memory Offset USB Controller Registers 32579BCore Logic Module USB Controller Registers Pciusb 286 HcInterruptEnable Register R/W Reset Value = 00000000h OwnershipChangeEnableRootHubStatusChangeEnable FrameNumberOverflowEnable Bit Description StartOfFrameEnable Offset 20h-23hOffset 24h-27h Offset 28h-2Bh Reset Value = 00000628h Reset Value = 01000003hBit Description Offset 38h-3Bh HcFrameRemaining Register RO Reserved. Read 0s BalPower Read LocalPowerStatusChange. Not supported. Always readOffset 50h-53h HcRhStatus Register R/W 3018 HcRhPortStatus1 Register R/W Reset Value = 00000000h Read PortResetStatusRead PortSuspendStatus AMD Geode SC1200/SC1201 Processor Data Book 291 292 Read PortEnableStatusRead CurrentConnectStatus AMD Geode SC1200/SC1201 Processor Data Book 293 Reserved Reset Value = xxh 294 AMD Geode SC1200/SC1201 Processor Data Book 295 ISA Legacy Register Space 43. DMA Channel Control Registers Priority Mode Timing ModeCore Logic Module ISA Legacy Register Space Write Transfer Mode Channel Number Mode Select32579BCore Logic Module ISA Legacy Register Space Bit Description Port 00Bh AMD Geode SC1200/SC1201 Processor Data Book 299 Write DMA Command Register, ChannelsUndefined Bit Description Port 0D2h Port 0D4hPort 0D6h Port 0D8h 44. DMA Page Registers 45. Programmable Interval Timer Registers Current Counter Mode BCD Mode Bit Description Port 042h WriteCounter Value Read Port 043h R/W 46. Programmable Interrupt Controller Registers Poll Command Register Read ModeBit Description IRQ1 / IRQ9 Mask IRQ0 / IRQ8 Mask Interrupt Service Register IRQ7 / IRQ15 In-Service IRQ6 / IRQ14 In-ServiceIRQ5 / IRQ13 In-Service IRQ4 / IRQ12 In-Service 47. Keyboard Controller Registers 48. Real-Time Clock Registers 49. Miscellaneous Registers AMD Geode SC1200/SC1201 Processor Data Book 309 310 General Features Video Input Port VIP InterfaceHardware Video Acceleration Graphics-Video Overlay and Blending Display Modes Video Input PortVIP Tvout Functional Description Video SupportVBI Support Video Processor Module Active Video Video Input Port VIP Direct Mode and Capture Mode Configurations AMD Geode SC1200/SC1201 Processor Data Book 317 BobAddress not changed during runtime Weave AMD Geode SC1200/SC1201 Processor Data Book 319 Capture VBI ModePing-pongs between the two buffers during runtime Video Block Video Input FormatterLine Buffer 320 Horizontal Downscaler with 4-Tap Filtering FilteringHorizontal Downscaler Maintaining Aspect Ratio Line Buffers Formatter2.5 2-Tap Vertical and Horizontal Upscalers Ai,j Ai,j+1 Ai+1,jAi+1,j+1 Mixer/Blender Block CSCRGB RAM Valid Mixing/Blending Configurations Filter2 Bit Mode CommentFlicker 324 YUV to RGB CSC in Video Data Path Gamma CorrectionRGB to YUV CSC 3.4 1/2 Y Flicker Filter Graphics Window Video WindowCursor Window Alpha Windows Truth Table for Alpha Blending Mixing/Blending OperationColor CHROMASEL1 328 Flicker Filter, Interlaced Video YUV Mixing/Blending Mode Tvout BlockFlicker Filter and Scan Rate Conversion Vesa Vesa DDSC2B and Dpms Support Integrated DACs Power Sequence TFT InterfaceHSYNC, VSYNC, TFTDE, Tftdck T1 is a programmable multiple of frame time T0+T1 Divider Phase Charge Loop Integrated PLLCompare Pump Filter Divider Out 332 F4BAR0+ F4BAR0 Video Processor Configuration Registers SummaryF4 PCI Header Registers for Video Processor Support Summary 32579BVideo Processor Module Register Summary 334 Name Value Tvout Configuration Registers F4BAR2 VIP Support Registers SummaryEncoder Registers F4BAR2+ Reset Value 0504h Reset Value 030000hVideo Processor Registers Function 3112 VIP Base Address 110 Address Range. Read Only AMD Geode SC1200/SC1201 Processor Data Book 337 Video Processor Module Video Processor Registers FunctionIndex 3Eh-FFh Reserved Video Configuration Register R/W Reset Value 00000000h EN42X Enable 42x Format. Allows format selectionVideo Processor Support Registers F4BAR0 To 0 or 1 should be written with a value that is read Offset 04h-07h Display Configuration Register R/W Tions of the power sequence control lines 16143028 Ddcsdaout DDC Output Data. DDC data bit for output Offset 08h-0Bh Video X Position Register R/W 340 Bit Description 100 AMD Geode SC1200/SC1201 Processor Data Book 341 Reset Value 00001400h 12 PLL2PWREN PLL2 Power-Down EnableBit Description Offset 1Ch-1Fh Block Offset 20h-23h DTS Downscale Type Select Offset 40h-43h Video Downscaler Coefficient Register R/WFLTCO4 Filter Coefficient 4. For the tap-4 filter FLTCO3 Filter Coefficient 3. For the tap-3 filter Reserved Signen Signature Enable Reset Value 0000xxxxhReset Value 00060000h Bit Description Offset 44h-47h CRC Signature Register R/W 100 i.e., shift one line otherwise, leave at AMD Geode SC1200/SC1201 Processor Data Book 345 Bit Description Offset 50h-53h Offset 54h-57hOffset 60h-63h Alpha Window 1 X Position Register R/W 346 AMD Geode SC1200/SC1201 Processor Data Book 347 3118Decremented until it is reloaded via bit 17 Loadalpha 348 Offset 90h-93h Offset 94h-97hOffset 400h-403h Video Fifo Underflow Empty Video Fifo OverFlow Full VBI Fifo Underflow EmptyVBI Fifo Overflow Full Upscale horizontally VBI data by Genlocktouten GenLock Timeout Enable Bit Description Offset 414h-417h3120 Reserved 190 Port Offset 41Ch-41Fh Ctgenlocken Enable Continuous GenLock Function Sggenlocken Enable a Single GenLock FunctionOffset 424h-427h 3121 Reserved 200 Bit Description Offset 80Ch-80Fh Offset 810h-813h Horintp Horizontal Interpolation Fieldinvr Field InvertOffset 81Ch-81Fh Offset C00h-C03h 2920 AMD Geode SC1200/SC1201 Processor Data Book 355 TV DAC Mode Bits Ball No A23 ModeOffset C08h-C0Bh D24 A24 Offset C24h-C27h 3114Offset C28h-C2Bh AMD Geode SC1200/SC1201 Processor Data Book 357 Reset Value 00000020h Reset Value 00000004hBit Description Offset C2Ch-C2Fh Offset C50h-C53h 10. F4BAR2+Memory Offset VIP Configuration Registers VIP Support Registers F4BAR2All other decodes Reserved AMD Geode SC1200/SC1201 Processor Data Book 359 Capture Store to Memory VBI Data Capture Store to Memory Video DataReserved.Read Only Current Field. Read Only 2322 Video Data Capture Active. Read Only Reserved. Read Only Run Status. Read OnlyOffset 14h-17h Offset 24h-27h Video Data Even Base Register R/W 3116 Reserved 150 Offset 2Ch-3FhOffset 44h-47h VBI Data Even Base Register R/W Offset 48h-4Bh VBI Data Pitch Register R/W Jtag Mode Instruction Support Testability JtagMandatory Instruction Support Optional Instruction Support 364 General Specifications Power/Ground Connections and DecouplingElectro Static Discharge ESD Absolute Maximum Ratings 366 Symbol Parameter Min Typ Max Unit CommentsOperating Conditions Power Planes of External Interface Signals Power Plane Signal Names VCC Balls VSS BallsPower State Parameter Definitions DC Current DC Characteristics for On State DC Characteristics for Active Idle, Sleep, and Off States Symbol Parameter Note Min Typ Max Unit CommentsSymbol Parameter Min Typ Max Unit Comment Ball Capacitance and Inductance Pull-Up and Pull-Down Resistors Balls with PU/PD ResistorsVIO External PU or PD resistor DC Characteristics Symbol Description ReferenceWire 10. Buffer Types Inpci DC Characteristics Inab DC CharacteristicsInbtn DC Characteristics Instrp DC Characteristics INT DC CharacteristicsInts DC Characteristics INTS1 DC Characteristics Inusb DC Characteristics ODn DC Characteristics Odpci DC Characteristics Op/n DC CharacteristicsOpci DC Characteristics Ousb DC Characteristics AC Characteristics 11. Default Levels for Measurement Switching ParametersSymbol Parameter Value CLK Inputs Memory Controller InterfaceOutputs 32579BElectrical Specifications 12. Memory Controller Timing ParametersSDCLK30, Sdclkout high time 13.5 T1, t2, t3 t10 SDCLK30 Control Output, MA120BA10, MD630 MD630 Data Valid Read Data Vpckin Vref 14. Video Output Port Timing Parameters CRT and TFT Interface 15. TFT Timing Parameters Symbol Parameter Note Min Max Unit Comments 16. CRT Vesa Compatible DAC RED, GREEN, and Blue Outputs RES IRELSB DNL LSB Tvref 19. ACCESS.bus Output Timing Parameters ACCESS.bus Interface18. ACCESS.bus Input Timing Parameters AB1D AB2D AB1C AB2C AMD Geode SC1200/SC1201 Processor Data Book 387 AB1D AB2D AB1C AB2CAB1D AB2D AB1C 20. PCI AC Specifications PCI Bus 64VIO Equation a Equation B 21. PCI Clock Parameters Pciclk 0.4 V IO 22. PCI Timing Parameters Measurement and Test Conditions Symbol Value Unit Comments23. Measurement Condition Parameters Power SignalsInput Valid Ms typ Symbol Parameter Bits Type Comments Sub-ISA Interface24. Sub-ISA Timing Parameters Bus Width Min Bus Width Min Max Symbol Parameter Bits Type Comments MEMR#/DOCR#/IOR# ROMCS#/DOCCS# IOR#/RD#/TRDE#MEMR#/DOCR# IOW#/WR# MEMW#/DOCW# DOCCS#/ROMCS# IOCS10#IOW#/WR# MEMW#/DOCW# TRDE# D150 LPC Interface 25. LPC and Serirq IDE signals fall time from 0.9V IO to 0.1V IO = 40 pF IDE signals rise time from 0.1V IO to 0.9V IO = 40 pFIDE Interface Timing 26. IDE General Timing Parameters IDERST# pulse width Mode Symbol Parameter Unit Comments 27. IDE Register Transfer to/from Device Timing ParametersCycle time min Width 8-bit min Addr valid1 IDEIOR0# IDEIOW0# Write IDEDATA70Read IDEDATA70 IDEIORDY0 2,3 402 28. IDE PIO Data Transfer to/from Device Timing Parameters165 125 100 AMD Geode SC1200/SC1201 Processor Data Book 403 IDEIOR0# IDEIOW0# Write IDEDATA150Read IDEDATA150 29. IDE Multiword DMA Data Transfer Timing Parameters AMD Geode SC1200/SC1201 Processor Data Book 405 IDECS10#IDEDREQ0 IDEDACK0# IDEIOR0# IDEIOW0# 406 Mode Symbol Parameter Min Max Unit Comments30. IDE UltraDMA Data Burst Timing Parameters IDEREQ0 STOP0IDEIOR0# HDMARDY0# IDEIRDY0 DSTROBE0 IDEIRDY0 DSTROBE0 at device IDEDATA150 at device IDEIRDY0 DSTROBE0 at hostIDEDATA150 at host 408 IDEDREQ0 device IDEDACK0# host IDEIOW0#STOP0# hostIDEIOR0#HDMARDY0# AMD Geode SC1200/SC1201 Processor Data Book 409 410 IDEDREQ0 deviceIDEIOW0# STOP0# IDEIOW0# STOP0# host IDEIOR0# HDMARDY0# host IDEIRDY0 DSTROBE0 device IDEDATA150 deviceIDECS01# IDEADDR20 DevicetUI IDEDACK0# host IDEIOW0# STOP0# hostIDEIORDY0 DDMARDY0 device IDEIOR0# HSTROBE0# host HSTROBE0# At hostIDEDATA150 At host IDEIOR0# HSTROBE0# at device IDEDATA150 at device IDEDREQ0 device IDEDACK0# host IDEIOW0# STOP0# host IDEIORDY0# DDMARDY0#IDEIOR0# HSTROBE0# 414 IDEIORDY0# DDMARDY0# device IDEDATA150 host IDEADDR20 IDECS01#IDEDACK0# host AMD Geode SC1200/SC1201 Processor Data Book 415 416 IDEDREQ0 device IDEDACK0 host IDEIOW0# STOP0# hostIDEDATA150 host IDECS01# IDEADDR20 Low Speed Source Note Universal Serial Bus USB 31. USB Timing ParametersFull Speed Receiver EOP Width Note Source EOP width Host upstreamReceiver data jitter tolerance for paired Low Speed Receiver EOP Width Note Rise Time Fall Time Differential Data LinesDifferential Data Lines Crossover Points 2.0 Consecutive Transitions Differential Data to SE0 Skew Data Crossover LevelEOP Width Differential Crossover Points Data Lines Modulation signal period TCPN + Transmitter Sharp-IR and Consumer Remote ControlSIR signal pulse width Setting of the Rxhsc bit bit 5 of the Rccfg register FIR Fast IR Port Timing 33. Fast IR Port Timing ParametersMIR Busy ACK# STB# Unit Comments Symbol Parameter Min35. Enhanced Parallel Port Timing Parameters 36. ECP Forward Mode Timing Parameters Extended Capabilities Port ECP TimingAFD# Busy 37. ECP Reverse Mode Timing Parameters BUSY# Audio Interface Timing AC97 38. AC Reset Timing Parameters AC97RST# inactive to Bitclk 162.8 Startup delaySync inactive to Bitclk startup 162.8 Delay AC97RST# active low pulse width 40. AC97 Clocks Parameters AC97CLK Vold 41. AC97 I/O Timing Parameters SDATAOUT/SYNC SDATAIN, SDATAIN2 42. AC97 Signal Rise and Fall Timing Parameters 43. AC97 Low Power Mode Timing Parameters End of Slot 2 to Bitclk Sdatain lowSlot Bitclk Sdataout Power Management Power management event to ONCTL# Assertion44. PWRBTN# Timing Parameters ONCTL# PWRBTN# PWRBTN# ONTCL# PWRCNT21 POR# POR# 32KHZ 434 TDI, TMS setup time Non-test inputs setup timeJtag Interface 48. Jtag Timing Parameters TDI, TMS hold time Output Signals Input SignalsTDI TMS TDO 436 Case-to-Ambient Thermal Resistance Example @ 85C Thermal CharacteristicsΘJC ×C/W Heatsink Considerations ExampleAssume P max = 5W and TA max = 40C Therefore Assume P max = 9W and TA max = 40C Therefore AMD Geode SC1200/SC1201 Processor Data Book 439 Physical DimensionsPackage Specifications BGU481 Package Bottom View 440 Order Information Macrovision Product NoticeOrdering Part Number Core Frequency MHz Revision # Revisions / Comments Data Book Revision HistoryTable A-1. Revision History