Inusb DC Characteristics, ODn DC Characteristics

32579B

Electrical Specifications

9.2.8INUSB DC Characteristics

Symbol	Parameter	Min	Max	Unit	Comments

VIH	Input High Voltage	2.0	VIO+0.3	V
			(Note 1)

VIL	Input Low Voltage	-0.5	0.8	V
		(Note 1)

IIL	Input Leakage Current		10	µA	VIN = VIO
			-10	µA	VIN = VSS
VDI	Differential Input Sensitivity	0.2		V	(D+)-(D-) and Figure 9-1
VCM	Differential Common Mode	0.8	2.5	V	Includes VDI Range
	Range

VSE	Single Ended Receiver	0.8	2.0	V
	Threshold

Note 1. Not 100% tested.

Minimum Differential Sensitivity (volts)

1.0

0.8

0.6

0.4

0.2

0.0

0.00.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 Common Mode Input Voltage (volts)

Figure 9-1. Differential Input Sensitivity for Common Mode Range

9.2.9OAC97 DC Characteristics

Symbol	Parameter	Min	Max	Unit	Comments

VOH	Output High Voltage	0.9VIO		V	lOH = -5 mA
VOL	Output Low Voltage		0.1VIO	V	lOL = 5 mA

9.2.10ODn DC Characteristics

Symbol	Parameter	Min	Max	Unit	Comments

VOL	Output Low Voltage		0.4	V	IOL = n mA

374	AMD Geode™ SC1200/SC1201 Processor Data Book

Page 374

Image 374

AMD SC1200, SC1201 manual Inusb DC Characteristics, ODn DC Characteristics

Contents

Publication ID 32579B AMD Geode SC1200/SC1201 Processor Data Book Advanced Micro Devices, Inc. All rights reserved Contacts Trademarks Contents Core Logic Module Electrical SpecificationsPackage Specifications Video Processor Module Typical Battery Current Normal Operation Mode Power Supply ConnectionsTypical Battery Configuration ACCESS.bus Data Transaction USB EOP Width Timing Diagram 420 Multiword DMA Data Transfer Timing Diagram 405USB Data Signal Rise and Fall Timing Diagram 419 Fast IR Timing MIR and FIR Diagram 422 426 424425 427 32579B ACB1 and ACB2 Configuration Register IRCP/SP3 Configuration RegisterSerial Ports 1 and 2 Configuration Register Parallel Port Configuration Register 166 Banks 0 and 1 Common Control and Status Registers 118119 167 F2BAR4+I/O Offset IDE Controller Configuration Registers Pciusb USB PCI Configuration Register SummaryF0BAR0+I/O Offset Gpio Configuration Registers F3 PCI Header Registers for Audio Configuration 402 384400 404 Core Logic General DescriptionVideo Processor SuperI/O GX1 Processor Module FeaturesGeneral Features Video Processor Module Nand Eeprom Other FeaturesCore Logic Module SuperI/O Module 32579B Architecture Overview 32579B GX1 ModuleMemory Controller SC1200/SC1201 Processor Memory Controller Registers Width Memory Offset Bits Type Name/Function Reset ValueSC1200/SC1201 Processor Memory Controller Register Summary MCMEMCNTRL2 R/W Rsvd Reserved. Write as 0070h Bit Description GXBASE+8408h-840BhMcbankcfg R/W Rsvd Reserved. Write as GXBASE+840Ch-840Fh Mcdracc R/W Mcgbaseadd R/WMcdradd R/W 1 GX1 Module Interface Fast-PCI BusDisplay Video Input Port Power-On Reset Clock, Timers, and Reset LogicReset Logic System Reset 32579B SC1200/SC1201 Signal Definitions 32579BAMD Geode Processor USB Jtag Interface Signal Definitions Legend Mnemonic Definition SC1200/SC1201 Configuration BGU481 Ball Assignment Sorted by Ball Number REQ0# GNT0# GPIO7 AFD#/DSTRB# PAR GPIO12 FTRDY# AC1 IDEDATA1 Buffer1 Power Signal Name Ball Buffer Power Signal Name BGU481 Ball Assignment Sorted Alphabetically by Signal Name Signal Name Ball No C11 F30FC/BE0# D21 FC/BE1# B17 MD25 AC28 MD23MD24 MD26 AC29 A2, A30, B2, B13 C24N13, N14, N18 F31 Strap Options Nominal External PU/PD Strap SettingsStrap Options Default Alternate Ball No Signal Configuration Multiplexing ConfigurationTwo-Signal/Group Multiplexing TFT, CRT, PCI, GPIO, System AC97 Fpci Monitoring ACCESS.busInternal Test Three-Signal/Group Multiplexing Four-Signal/Group Multiplexing Gpio UART2 IDE2 Maximum Core Clock Multiplier. These strap signals Signal DescriptionsSignal Name Ball No Type Description Mux Boot ROM is 16 Bits Wide. This strap signal enables Memory Interface Signals Column Address Strobe. RAS#, CAS#, WE# and CKE Video Port Interface Signals 4 CRT/TFT Interface Signals Digital RGB Data to TFT Current Compensation for TV DAC. a 0.1 µF to 1.2 µF TV Interface SignalsSuper Video Chrominance. S-Video chrominance sig ACCESS.bus Interface Signals PCI Bus Interface Signals INTC# INTA#INTB# INTD# AA2 DEVSEL# STOP#LOCK# BHE# REQ1# PERR#SERR# REQ0# Sub-ISA Interface Signals Low Pin Count LPC Bus Interface Signals IDE Interface Signals Universal Serial Bus USB Interface Signals Serial Ports UARTs Interface Signals Parallel Port Interface Signals Fast Infrared IR Port Interface Signals General Purpose Wakeup I/Os. These signals each 15 AC97 Audio Interface SignalsPower Management Interface Signals Serial Bus Synchronization. This bit is asserted to syn PWRCNT1 AK6 Suspend Power Plane Control 1 and 2. Control signalPWRBTN# AH5 PWRCNT2 AL7 Gpio Interface Signals Fast-PCI Bus Monitoring Signals. When enabled, this Debug Monitoring Interface SignalsJtag Interface Signals System Management Interrupt. This is the input to Memory Internal Test Signals. These signals are used Test and Measurement Interface SignalsPLL6, PLL5 and PLL2 Bypass. These signals are used Thermal Diode Positive / Negative. These signals are for Power and Ground Connections1 General Configuration Block 32579B Configuration Block AddressesGeneral Configuration Block Register Summary Width Offset Bits PMR27 Ball # Internal Test Signals Name Add’l DependenciesOther Signal Add’l Dependencies Fpcimon General Configuration Block Ball # IDE Signals CRT, Gpio and TFT Signals Name PP/ACB1/FPCI TFT/VOP Name Add’l Dependencies Ball # Gpio Signals LPC Signals Name Add’l Dependencies 32579BGeneral Configuration Block Reserved General Configuration Block Offset 3Dh Revision Register REV RO Offset 3Eh-3Fh Configuration Base Address Register CBA ROOffset 38h Interrupt Selection Register Intsel R/W Watchdog Timer Functional Description 3describes the Watchdog registers Watchdog RegistersWatchdog Interrupt Usage Hints Watchdog Status Register Wdsts R/WC Reset Value 00h High-Resolution TimerHigh-Resolution Timer Registers Offset 05h-07h Tmen Timer Interrupt Enable Reset Value xxxxxxxxhTmclksel Timer Clock Select Bit Description Offset 08h-0Bh Clock Generators and PLLs Component Parameters Values Tolerance 1 27 MHz Crystal OscillatorCrystal Oscillator Circuit Components Core Clock Frequency 2 GX1 Module Core ClockInternal Fast-PCI Clock Strapped Core Clock Frequency Video Processor Clocks SuperI/O ClocksCore Logic Module Clocks Clock generator and PLL registers are described in Table Clock Generator ConfigurationClock Registers 33.3 MHz 1514Reserved. Must be set to 1110 66.7 MHz AB1C AB1D AB2C AB2D Outstanding FeaturesISA Serial Port PC98 and Acpi CompliantParallel Port Serial Port 3 / Infrared IR Communication Port Internal Internal Signals AccessSignals Module Architecture Index-Data Register Pair Configuration Structure / AccessSIO Configuration Options LDN Assignments Default Configuration Setup Address Decoding Logical Device Control and Configuration Registers Standard Configuration RegistersSIO Control and Configuration Registers Standard Logical Device Configuration Registers Standard Configuration Registers DMA Channel Select 1 R/W Index F0h-FEh Logical Device Configuration R/W32579BSuperI/O Module Index Type Name Power Rail Reset Value SIO Control and Configuration RegistersSIO Control and Configuration Register Map SID. SIO ID Logical Device Control and Configuration Relevant RTC Configuration Registers RTC Configuration Registers Base Address MSB register Relevant SWC RegistersLDN 01h System Wakeup Control 10. IRCP/SP3 Configuration Register Relevant IRCP/SP3 Registers 11. Relevant Serial Ports 1 and 2 Registers 12. Serial Ports 1 and 2 Configuration RegisterSerial Ports 1 and 2 Configuration register LDN 03h and 08h Serial Ports 1 ACB1 and ACB2 Configuration register 14. ACB1 and ACB2 Configuration RegisterLDN 05h and 06h ACCESS.bus Ports 1 13. Relevant ACB1 and ACB2 Registers 16. Parallel Port Configuration Register 15. Relevant Parallel Port Registers Bus Interface RTC Clock Generation X32I External X32O Battery = 0.1 μFReal-Time Clock RTC 17. Crystal Oscillator Circuit Components Oscillator Startup Signal ParametersExternal Elements External Oscillator Daylight Saving AlarmsTimekeeping Data Format Leap Years Power Supply 18. System Power States 110 Battery-Backed RAMs and RegistersInterrupt Handling 20. RTC Registers RTC Registers19. RTC Register Map Index Type Name CRD is Index 05h Hours Alarm Register Hora R/WIndex 04h Hours Register HOR R/W 112 Index Programmable Century Register CEN R/W Index Programmable Month Alarm Register Mona R/WIndex 0Ch RTC Control Register C CRC RO AMD Geode SC1200/SC1201 Processor Data Book 113 23. BCD and Binary Formats 21. Divider Chain Control / Test Selection22. Periodic Interrupt Rate Encoding Parameter BCD Format Binary Format RTC General-Purpose RAM Map 24. Standard RAM Map 0Eh 7Fh Battery-backed general-purpose Byte RAM00h 7Fh Battery-backed general-purpose Byte RAM 25. Extended RAM Map 26. Time Range Limits for Ceir Protocols System Wakeup Control SWCEvent Detection Type Name Value SWC Registers27. Banks 0 and 1 Common Control and Status Register Map Offset Type Name Value 29. Banks 0 and 1 Common Control and Status Registers 30. Bank 1 Ceir Wakeup Configuration and Control Registers Ceir Pulse Change, Range 1, High Limit Bit Description Ceir Wakeup Range 1 RegistersBank 1, Offset 0Ah IRWTR1L Register R/W Ceir Wakeup Range 2 Registers ABD ABC ACCESS.bus InterfaceData Transactions AMD Geode SC1200/SC1201 Processor Data Book 121 ABC ACK Acknowledge ACK CycleABD MSB Arbitration on the Bus Master ModeAcknowledge After Every Byte Rule Addressing Transfer Formats Master Receive Sending the Address ByteMaster Transmit Master Stop Slave Mode Configuration 32. ACB Registers ACB Registers31. ACB Register Map MASTER. RO EN Enable Reserved Inten Interrupt EnableSaen Slave Address Enable Stop Stop 33. Parallel Port Register Map for First Level Offset Legacy Functional BlocksParallel Port 34. Parallel Port Register Map for Second Level Offset 130 35. Parallel Port Bit Map for First Level Offset36. Parallel Port Bit Map for Second Level Offset Uart Functionality SP1 and SP2 Type Name 40. Bank 2 Register Map 38. Bank Selection Encoding39. Bank 1 Register Map 41. Bank 3 Register Map Register Bits 42. Bank 0 Bit Map43. Bank 1 Bit Map Register Bits Offset 134 44. Bank 2 Bit Map45. Bank 3 Bit Map IRCP/SP3 Register and Bit Maps 3.1 IR/SP3 Mode Register Bank Overview46. Bank 0 Register Map 01h Register Throughout Offset 00h All Banks 49. Bank 2 Register Map 47. Bank Selection Encoding48. Bank 1 Register Map BSR Bits Bank Selected Functionality 52. Bank 5 Register Map 50. Bank 3 Register Map51. Bank 4 Register Map 55. Bank 0 Bit Map 53. Bank 6 Register Map54. Bank 7 Register Map 58. Bank 3 Bit Map 56. Bank 1 Bit Map57. Bank 2 Bit Map 59. Bank 4 Bit Map 62. Bank 7 Bit Map 60. Bank 5 Bit Map61. Bank 6 Bit Map Feature List Video Processor Interface ConfigIntegrated Audio Low Pin Count LPC Interface Fast-PCI Interface to External PCI Bus Pserial Interface IDE Controller IDE Configuration RegistersPIO Mode Video Retrace Interrupt Physical Region Descriptor Format Stop UltraDMA/33 Signal DefinitionsUltraDMA/33 Mode DMARDY# Strobe Ideiordy IOCS0#/IOCS1# Universal Serial BusSub-ISA Bus Interface Docw Fast-PCICLK Sub-ISA Support of Delayed PCI TransactionsSub-ISA Bus Cycles AD310 Read AD310 Write FRAME# IRDY# TRDY# STOP# Bale ISA RD#, IOR# 5.4 I/O Recovery DelaysREQ# GNT# Sub-ISA Bus Data Steering AD310 ISA DMASD150 ROM Interface PCI and Sub-ISA Signal Cycle MultiplexingCycle Multiplexed PCI / Sub-ISA Balls PCI DMA Controller FRAME# TRDY#, IRDY#ROMCS#, DOCCS# IOCS0#, IOCS1# PAR DEVSEL#,STOP# DMA Channels DMA Transfer Types DMA Transfer ModesDMA Controller Registers DMA Priority DMA Page Registers and Extended Addressing Programmable Interval TimerDMA Addressing Capability DMA Address Generation Master PIC Interrupt MappingProgrammable Interrupt Controller Mapping PIC Shadow Register PIC Interrupt SequencePIC I/O Registers PCI Compatible Interrupts 7.1 I/O Port 092h System Control Fast Keyboard Gate Address 20 and CPU ResetKeyboard Support 7.2 I/O Port 061h System Control Power Management Logic Wakeup Events Capability Power Management Events Power Planes Control Signals vs Sleep StatesPower Planes vs. Sleep/Global States Thermal Monitoring Power ButtonPower Button Override AMD Geode SC1200/SC1201 Processor Data Book 161 APM Support Power Management ProgrammingCPU Power Management Suspend Modulation AMD Geode SC1200/SC1201 Processor Data Book 163 Volt SuspendSave-to-Disk General Purpose Timers Peripheral Power ManagementDevice Idle Timers and Traps Acpi Timer Register F1BAR0+I/O Power Management SMI Status Reporting RegistersModule Located at F0 Index xxh Unless Otherwise Noted Device Power Management Programming SummaryPower Management Programming Summary F1BAR0+I/O Gpio Interface Integrated Audio Audio Data Buffer Reserved Size 11. Physical Region Descriptor FormatByte Memory Region Base Address PRD1 PRD2 PRD3 12.2 AC97 Codec Interface Codec Configuration/Control RegistersCodec Command Register Codec Gpio Status and Control Registers VSA Technology Trap SMI Enable RegisterVSA Technology Support Hardware Audio SMI Related Registers Module Core Logic Module Internal IRQ Control Register IRQ Configuration RegistersInternal IRQ Enable Register LPC Interface 12. Cycle Types Register Descriptions PCI Configuration Space and Access Methods13. PCI Configuration Address Register 0CF8h Core Logic module. Included in the tables are the regis Ter’s reset values and page references where the bit forRegister Summary Mats are found Width Reset Reference F0 Index Bits AMD Geode SC1200/SC1201 Processor Data Book 177 32579BCore Logic Module Register Summary 178 F0BAR0+ 15. F0BAR0 Gpio Support Registers Summary16. F0BAR1 LPC Support Registers Summary F0BAR1+ 18. F1BAR0 SMI Status Registers Summary F1BAR0+ 00h-03h Pcnt Processor Control Register 19. F1BAR1 Acpi Support Registers SummaryF1BAR1+ 20h PM2CNT PM2 Control Register 00h 21h-FFh Not Used Width Reset Reference F2 Index Bits 182 22. F3 PCI Header Registers for Audio Support Summary Width Reset Reference F3 Index Bits21. F2BAR4 IDE Controller Support Registers Summary F2BAR4+ F3BAR0+ Width Reset23. F3BAR0 Audio Support Registers Summary 184 F5BAR0+ Width Reset Reference F5 Index Bits25. F5BAR0 I/O Control Support Registers Summary AMD Geode SC1200/SC1201 Processor Data Book 185 Pciusb 26. Pciusb USB PCI Configuration Register SummaryName Reset Value Width Reference Index Bits AMD Geode SC1200/SC1201 Processor Data Book 187 27. Usbbar USB Controller Registers SummaryUSBBAR0 188 28. ISA Legacy I/O Register SummaryDMA Page Registers Table Programmable Interrupt Controller Registers Table Programmable Interval Timer Registers TablePort Type Name Reference Keyboard Controller Registers Table General Remarks Chipset Register SpaceBridge, GPIO, and LPC Registers Function Index 09h-0Bh Core Logic Module Bridge, GPIO, and LPC Registers FunctionData Parity Detected. This bit is set when AMD Geode SC1200/SC1201 Processor Data Book 191 Index 0Fh PCI Bist Register RO Index 0Eh PCI Header Type RO Reset Value 80hSlave response 316 Gpio Base Address PCI Subtractive Decode AMD Geode SC1200/SC1201 Processor Data Book 193 Index 43h Reset Control Register R/W Reset Value 01hIndex 42h 194 Index 47h Index 45hIndex 46h AMD Geode SC1200/SC1201 Processor Data Book 195 PIT Counter 1 Enable Reset Value 7BhPIT Software Reset PIT Counter 0 Enable AMD Geode SC1200/SC1201 Processor Data Book 197 ROM/AT Logic Control Register R/W Reset Value 98hGenerate SMI on A20M# Toggle Index 5Bh Decode Control Register 2 R/W Bit Description Index 54h-59hIndex 5Ah 198 INTD# Ball AA2 Target Interrupt INTB# Ball C26 Target InterruptINTA# Ball D26 Target Interrupt INTC# Ball C9 Target Interrupt 200 150Index 72h Index 76h Index 73hIndex 74h-75h Chip Select 0 Positive Decode IOCS0# Ing the upper 19 bits of the incoming PCI address AD3113 202 AMD Geode SC1200/SC1201 Processor Data Book 203 Power Management Enable Register 2 R/W Reset Value 00hTimer expires Disable Enable 204 Parallel/Serial Access Trap Power Management Enable Register 3 R/W Reset Value 00hKeyboard/Mouse Access Trap AMD Geode SC1200/SC1201 Processor Data Book 205 Index 83h Power Management Enable Register 4 R/W Floppy Disk Access TrapPrimary Hard Disk Access Trap 206 Index 84h Second Level PME/SMI Status Mirror Register 1 RO AMD Geode SC1200/SC1201 Processor Data Book 207 208 AMD Geode SC1200/SC1201 Processor Data Book 209 210 Index 88h General Purpose Timer 1 Count Register R/WReserved. Always reads AMD Geode SC1200/SC1201 Processor Data Book 211 Re-trigger General Purpose Timer 1 on Floppy Disk ActivitySecond Millisecond 212 Index 8Bh General Purpose Timer 2 Control Register R/WIndex 8Dh Video Speedup Timer Count Register R/W AMD Geode SC1200/SC1201 Processor Data Book 213 Index 8Fh-92hIndex 93h Index 98h-99h Index 9Ah-9Bh Floppy Disk Idle Timer Count Register R/WIndex 97h 214 Index A6h-A7h Video Idle Timer Count Register R/W Index A8h-A9h Video Overflow Count Register R/W Index B0h-B3h Index AEh CPU Suspend Command Register WOIndex AFh Suspend Notebook Command Register WO Index B4h AMD Geode SC1200/SC1201 Processor Data Book 217 Index B9h PIC Shadow Register ROIndex BAh PIT Shadow Register RO Index BDh-BFh Index BCh Clock Stop Control Register R/W Reset Value 00hReserved. Set to CPU Clock Stop Index C0h-C3h Index CDh Bit Description Index CChMask Index CEh Index F5h Second Level PME/SMI Status Register 2 RC Index EDh-F3hIndex F4h 220 Index F6h Second Level PME/SMI Status Register 3 RC AMD Geode SC1200/SC1201 Processor Data Book 221 222 Index F7h Second Level PME/SMI Status Register 4 RCReserved. Read as Index F8h-FFh Gpio Support Registers 30. F0BAR0+I/O Offset Gpio Configuration RegistersI/O mapped registers accessed through F0BAR0 Ration registers are located. -29gives the bit formats 316 Reserved. Must be set to Offset 14h-17h GPDI1 Gpio Data In 1 Register ROF0BAR0+I/O Offset 18h is set, this edge generates a PME AMD Geode SC1200/SC1201 Processor Data Book 225 010011 = GPIO19 ball C9 000100 Bank010010 = GPIO18 ball AG1 000011 010100 = GPIO20 balls A9, N31 000101 AMD Geode SC1200/SC1201 Processor Data Book 227 3121 31. F0BAR1+I/O Offset LPC Interface Configuration RegistersLPC Support Registers Reserved. Set to AMD Geode SC1200/SC1201 Processor Data Book 229 Polarity selection 230 Number of IRQ Data Frames Reserved Serial IRQ EnableSerial IRQ Interface Mode AMD Geode SC1200/SC1201 Processor Data Book 231 232 LPC Floppy Disk Controller Address Select. Selects I/O Port LPC Game Port 1 Address Select. Selects I/O PortLPC Game Port 0 Address Select. Selects I/O Port LPC Midi Address Select. Selects I/O Port 234 Bit SMI Status and Acpi Registers Function 32. F1 PCI Header Registers for SMI Status and Acpi Support Core Logic Module SMI Status and Acpi Registers Function 33. F1BAR0+I/O Offset SMI Status RegistersSMI Status Support Registers AMD Geode SC1200/SC1201 Processor Data Book 237 238 Suspend Modulation Enable Mirror. Read to ClearOffset 02h-03h Top Level PME/SMI Status Register RO/RC AMD Geode SC1200/SC1201 Processor Data Book 239 Offset 04h-05h Yes To enable SMI generation, set F0 Index 82h6 =Yes To enable SMI generation, set F0 Index 82h5 = 240 AMD Geode SC1200/SC1201 Processor Data Book 241 242 Offset 0Ah-1BhThese addresses should not be written Offset 1Ch-1Fh AMD Geode SC1200/SC1201 Processor Data Book 243 Offset 24h-27h External SMI Register R/W3124 244 AMD Geode SC1200/SC1201 Processor Data Book 245 246 Offset 28h-4Fh Not Used Reset Value 00h50h-FFh Acpi Support Registers Offset 06h Smicmd OS/BIOS Requests Register R/W34. F1BAR1+I/O Offset Acpi Support Registers Clkval Clock Throttling Value. CPU duty cycle SCI generation is always enabled 248 Offset 0Ch-0Dh PM1ACNT PM1A Control Register R/W Offset 0Ah-0Bh PM1AEN PM1A PME/SCI Enable Register R/W1511 1514 Reserved. Must be set to 250 AMD Geode SC1200/SC1201 Processor Data Book 251 252 Consumer Electronic Infrared Gpwio Control Register 1 R/W Reset Value 00hGpwio Control Register 2 R/W Reset Value 00h Reserved 02h0 Gpwio Data Register R/W Reset Value 00h Reserved Reset Value 00h 254 Offset 21h-FFh Reset Value 00000F00hBit Description Offset 18h-1Bh AMD Geode SC1200/SC1201 Processor Data Book 255 IDE Controller Registers Function Bit Description Index 30h-3Fh PIOMODE. PIO modeCore Logic Module IDE Controller Registers Function AMD Geode SC1200/SC1201 Processor Data Book 257 258 Index 58h-5Bh Bit Description Index 48h-4BhIndex 50h-53h Index 60h-FFh IDE Controller Support Registers 260 Offset 0Bh Offset 09hOffset 0Ah Offset 0Ch-0Fh 37. F3 PCI Header Registers for Audio Configuration Audio Registers Function Core Logic Module Audio Registers Function 38. F3BAR0+Memory Offset Audio Configuration RegistersAudio Support Registers Offset 04h-07h 264 AMD Geode SC1200/SC1201 Processor Data Book 265 266 These bits change only on a fast write to an even address2316 AMD Geode SC1200/SC1201 Processor Data Book 267 268 Mask Internal IRQ11. Write Only Mask Internal IRQ15. Write OnlyMask Internal IRQ14. Write Only Mask Internal IRQ10. Write Only Assert Masked Internal IRQ14 Mask Internal IRQ4. Write OnlyMask Internal IRQ3. Write Only Reserved. Set to Assert Masked Internal IRQ12 Bit Description Assert Masked Internal IRQ1 AMD Geode SC1200/SC1201 Processor Data Book 271 Offset 2Ah-2Bh Audio Bus Master 1 Command Register R/W Reset Value 00hOffset 29h Audio Bus Master 1 SMI Status Register RC Offset 2Ch-2Fh Offset 32h-33h Audio Bus Master 2 Command Register R/W Reset Value 00hOffset 31h Audio Bus Master 2 SMI Status Register RC Offset 34h-37h Offset 3Ah-3Bh Audio Bus Master 3 Command Register R/W Reset Value 00hOffset 39h Audio Bus Master 3 SMI Status Register RC Offset 3Ch-3Fh Offset 42h-43h Audio Bus Master 4 Command Register R/W Reset Value 00hOffset 41h Audio Bus Master 4 SMI Status Register RC Offset 44h-47h Offset 4Ah-4Bh Audio Bus Master 5 Command Register R/W Reset Value 00hOffset 49h Audio Bus Master 5 SMI Status Register RC Offset 4Ch-4Fh Bus Expansion Interface Function 39. F5 PCI Header Registers for X-Bus Expansion Index 24h-27h Bit Description Index 1Ch-1FhIndex 20h-23h Index 28h-2Bh Index 4Ch-4Fh F5BAR3 Mask Address Register R/W Index 58h F5BARx Initialized Register R/W Reset Value 00hIndex 48h-4Bh F5BAR2 Mask Address Register R/W Index 50h-53h F5BAR4 Mask Address Register R/W 280 Bit Description Index 64h-67hIndex 68h-FFh F5 Index 10h, Base Address Register 0 F5BAR0 set 40. F5BAR0+I/O Offset X-Bus Expansion RegistersBus Expansion Support Registers Iotestporten Debug Test Port Enable Three USB transceivers. Default = 128USB transceivers. Default = 282 Core Logic Module USB Controller Registers Pciusb 41. Pciusb USB PCI Configuration RegistersUSB Controller Registers Pciusb AMD Geode SC1200/SC1201 Processor Data Book 283 Bit Description Index 06h-07h Status Register R/W Reset Value 08hIndex 0Dh Latency Timer Register R/W Reserved. Must be set to Index 08h 42. USBBAR+Memory Offset USB Controller Registers 32579BCore Logic Module USB Controller Registers Pciusb 286 RootHubStatusChangeEnable HcInterruptEnable Register R/W Reset Value = 00000000hOwnershipChangeEnable FrameNumberOverflowEnable Offset 24h-27h Bit Description StartOfFrameEnableOffset 20h-23h Offset 28h-2Bh Bit Description Offset 38h-3Bh HcFrameRemaining Register RO Reset Value = 00000628hReset Value = 01000003h Reserved. Read 0s Offset 50h-53h HcRhStatus Register R/W BalPowerRead LocalPowerStatusChange. Not supported. Always read 3018 Read PortSuspendStatus HcRhPortStatus1 Register R/W Reset Value = 00000000hRead PortResetStatus AMD Geode SC1200/SC1201 Processor Data Book 291 292 Read PortEnableStatusRead CurrentConnectStatus AMD Geode SC1200/SC1201 Processor Data Book 293 Reserved Reset Value = xxh 294 AMD Geode SC1200/SC1201 Processor Data Book 295 ISA Legacy Register Space 43. DMA Channel Control Registers Core Logic Module ISA Legacy Register Space Priority ModeTiming Mode Write 32579BCore Logic Module ISA Legacy Register Space Transfer ModeChannel Number Mode Select Bit Description Port 00Bh AMD Geode SC1200/SC1201 Processor Data Book 299 Write DMA Command Register, ChannelsUndefined Port 0D6h Bit Description Port 0D2hPort 0D4h Port 0D8h 44. DMA Page Registers 45. Programmable Interval Timer Registers Counter Value Read Current Counter Mode BCD ModeBit Description Port 042h Write Port 043h R/W 46. Programmable Interrupt Controller Registers Bit Description IRQ1 / IRQ9 Mask Poll CommandRegister Read Mode IRQ0 / IRQ8 Mask IRQ5 / IRQ13 In-Service Interrupt Service Register IRQ7 / IRQ15 In-ServiceIRQ6 / IRQ14 In-Service IRQ4 / IRQ12 In-Service 47. Keyboard Controller Registers 48. Real-Time Clock Registers 49. Miscellaneous Registers AMD Geode SC1200/SC1201 Processor Data Book 309 310 Hardware Video Acceleration General FeaturesVideo Input Port VIP Interface Graphics-Video Overlay and Blending VIP Display ModesVideo Input Port Tvout VBI Support Functional DescriptionVideo Support Video Processor Module Active Video Video Input Port VIP Direct Mode and Capture Mode Configurations AMD Geode SC1200/SC1201 Processor Data Book 317 BobAddress not changed during runtime Weave AMD Geode SC1200/SC1201 Processor Data Book 319 Capture VBI ModePing-pongs between the two buffers during runtime Line Buffer Video BlockVideo Input Formatter 320 Horizontal Downscaler Horizontal Downscaler with 4-Tap FilteringFiltering Maintaining Aspect Ratio 2.5 2-Tap Vertical and Horizontal Upscalers Line BuffersFormatter Ai,j Ai,j+1 Ai+1,jAi+1,j+1 RGB Mixer/Blender BlockCSC RAM Flicker Valid Mixing/Blending ConfigurationsFilter2 Bit Mode Comment 324 RGB to YUV CSC YUV to RGB CSC in Video Data PathGamma Correction 3.4 1/2 Y Flicker Filter Cursor Window Graphics WindowVideo Window Alpha Windows Color Truth Table for Alpha BlendingMixing/Blending Operation CHROMASEL1 328 Flicker Filter and Scan Rate Conversion Flicker Filter, Interlaced Video YUV Mixing/Blending ModeTvout Block Vesa Vesa DDSC2B and Dpms Support Integrated DACs HSYNC, VSYNC, TFTDE, Tftdck Power SequenceTFT Interface T1 is a programmable multiple of frame time T0+T1 Compare Pump Filter Divider Out Divider Phase Charge LoopIntegrated PLL 332 F4BAR0+ F4BAR0 Video Processor Configuration Registers SummaryF4 PCI Header Registers for Video Processor Support Summary 32579BVideo Processor Module Register Summary 334 Encoder Registers Name Value Tvout Configuration RegistersF4BAR2 VIP Support Registers Summary F4BAR2+ Video Processor Registers Function Reset Value 0504hReset Value 030000h 3112 VIP Base Address 110 Address Range. Read Only AMD Geode SC1200/SC1201 Processor Data Book 337 Video Processor Module Video Processor Registers FunctionIndex 3Eh-FFh Reserved Video Processor Support Registers F4BAR0 Video Configuration Register R/W Reset Value 00000000hEN42X Enable 42x Format. Allows format selection To 0 or 1 should be written with a value that is read 3028 Offset 04h-07h Display Configuration Register R/WTions of the power sequence control lines 1614 Ddcsdaout DDC Output Data. DDC data bit for output Offset 08h-0Bh Video X Position Register R/W 340 Bit Description 100 AMD Geode SC1200/SC1201 Processor Data Book 341 Bit Description Offset 1Ch-1Fh Reset Value 00001400h12 PLL2PWREN PLL2 Power-Down Enable Block Offset 20h-23h FLTCO4 Filter Coefficient 4. For the tap-4 filter DTS Downscale Type SelectOffset 40h-43h Video Downscaler Coefficient Register R/W FLTCO3 Filter Coefficient 3. For the tap-3 filter Reset Value 00060000h Reserved Signen Signature EnableReset Value 0000xxxxh Bit Description Offset 44h-47h CRC Signature Register R/W 100 i.e., shift one line otherwise, leave at AMD Geode SC1200/SC1201 Processor Data Book 345 Offset 60h-63h Alpha Window 1 X Position Register R/W Bit Description Offset 50h-53hOffset 54h-57h 346 AMD Geode SC1200/SC1201 Processor Data Book 347 3118Decremented until it is reloaded via bit 17 Loadalpha 348 Offset 400h-403h Offset 90h-93hOffset 94h-97h Video Fifo Underflow Empty VBI Fifo Overflow Full Video Fifo OverFlow FullVBI Fifo Underflow Empty Upscale horizontally VBI data by 3120 Reserved 190 Genlocktouten GenLock Timeout EnableBit Description Offset 414h-417h Port Offset 41Ch-41Fh Offset 424h-427h Ctgenlocken Enable Continuous GenLock FunctionSggenlocken Enable a Single GenLock Function 3121 Reserved 200 Bit Description Offset 80Ch-80Fh Offset 810h-813h Offset 81Ch-81Fh Horintp Horizontal InterpolationFieldinvr Field Invert Offset C00h-C03h 2920 AMD Geode SC1200/SC1201 Processor Data Book 355 Offset C08h-C0Bh TV DAC Mode Bits Ball NoA23 Mode D24 A24 Offset C28h-C2Bh Offset C24h-C27h3114 AMD Geode SC1200/SC1201 Processor Data Book 357 Bit Description Offset C2Ch-C2Fh Reset Value 00000020hReset Value 00000004h Offset C50h-C53h All other decodes Reserved 10. F4BAR2+Memory Offset VIP Configuration RegistersVIP Support Registers F4BAR2 AMD Geode SC1200/SC1201 Processor Data Book 359 Reserved.Read Only Current Field. Read Only Capture Store to Memory VBI DataCapture Store to Memory Video Data 2322 Offset 14h-17h Video Data Capture Active. Read OnlyReserved. Read Only Run Status. Read Only Offset 24h-27h Video Data Even Base Register R/W Offset 44h-47h VBI Data Even Base Register R/W 3116 Reserved 150Offset 2Ch-3Fh Offset 48h-4Bh VBI Data Pitch Register R/W Mandatory Instruction Support Jtag Mode Instruction SupportTestability Jtag Optional Instruction Support 364 Electro Static Discharge ESD General SpecificationsPower/Ground Connections and Decoupling Absolute Maximum Ratings 366 Symbol Parameter Min Typ Max Unit CommentsOperating Conditions Power State Parameter Definitions Power Planes of External Interface SignalsPower Plane Signal Names VCC Balls VSS Balls DC Current DC Characteristics for On State Symbol Parameter Min Typ Max Unit Comment DC Characteristics for Active Idle, Sleep, and Off StatesSymbol Parameter Note Min Typ Max Unit Comments Ball Capacitance and Inductance VIO Pull-Up and Pull-Down ResistorsBalls with PU/PD Resistors External PU or PD resistor Wire DC CharacteristicsSymbol Description Reference 10. Buffer Types Inpci DC Characteristics Inab DC CharacteristicsInbtn DC Characteristics Ints DC Characteristics Instrp DC CharacteristicsINT DC Characteristics INTS1 DC Characteristics Inusb DC Characteristics ODn DC Characteristics Opci DC Characteristics Odpci DC CharacteristicsOp/n DC Characteristics Ousb DC Characteristics Symbol Parameter Value AC Characteristics11. Default Levels for Measurement Switching Parameters CLK Inputs Memory Controller InterfaceOutputs SDCLK30, Sdclkout high time 32579BElectrical Specifications12. Memory Controller Timing Parameters 13.5 BA10, MD630 T1, t2, t3 t10SDCLK30 Control Output, MA120 MD630 Data Valid Read Data Vpckin Vref 14. Video Output Port Timing Parameters CRT and TFT Interface 15. TFT Timing Parameters Symbol Parameter Note Min Max Unit Comments 16. CRT Vesa Compatible DAC RED, GREEN, and Blue Outputs LSB DNL RESIRE LSB Tvref 19. ACCESS.bus Output Timing Parameters ACCESS.bus Interface18. ACCESS.bus Input Timing Parameters AB1D AB2D AB1C AB2C AMD Geode SC1200/SC1201 Processor Data Book 387 AB1D AB2D AB1C AB2CAB1D AB2D AB1C 20. PCI AC Specifications PCI Bus 64VIO Equation a Equation B 21. PCI Clock Parameters Pciclk 0.4 V IO 22. PCI Timing Parameters Measurement and Test Conditions Symbol Value Unit Comments23. Measurement Condition Parameters Input Valid PowerSignals Ms typ 24. Sub-ISA Timing Parameters Symbol Parameter Bits Type CommentsSub-ISA Interface Bus Width Min Bus Width Min Max Symbol Parameter Bits Type Comments MEMR#/DOCR#/IOR# MEMR#/DOCR# ROMCS#/DOCCS#IOR#/RD#/TRDE# IOW#/WR# MEMW#/DOCW# IOW#/WR# MEMW#/DOCW# TRDE# DOCCS#/ROMCS#IOCS10# D150 LPC Interface 25. LPC and Serirq IDE Interface Timing 26. IDE General Timing Parameters IDE signals fall time from 0.9V IO to 0.1V IO = 40 pFIDE signals rise time from 0.1V IO to 0.9V IO = 40 pF IDERST# pulse width Cycle time min Mode Symbol Parameter Unit Comments27. IDE Register Transfer to/from Device Timing Parameters Width 8-bit min Read IDEDATA70 Addr valid1IDEIOR0# IDEIOW0# Write IDEDATA70 IDEIORDY0 2,3 402 28. IDE PIO Data Transfer to/from Device Timing Parameters165 125 100 AMD Geode SC1200/SC1201 Processor Data Book 403 IDEIOR0# IDEIOW0# Write IDEDATA150Read IDEDATA150 29. IDE Multiword DMA Data Transfer Timing Parameters AMD Geode SC1200/SC1201 Processor Data Book 405 IDECS10#IDEDREQ0 IDEDACK0# IDEIOR0# IDEIOW0# 406 Mode Symbol Parameter Min Max Unit Comments30. IDE UltraDMA Data Burst Timing Parameters IDEIOR0# HDMARDY0# IDEREQ0STOP0 IDEIRDY0 DSTROBE0 IDEDATA150 at host IDEIRDY0 DSTROBE0 at deviceIDEDATA150 at device IDEIRDY0 DSTROBE0 at host 408 IDEIOR0#HDMARDY0# IDEDREQ0 device IDEDACK0# hostIDEIOW0#STOP0# host AMD Geode SC1200/SC1201 Processor Data Book 409 410 IDEDREQ0 deviceIDEIOW0# STOP0# IDECS01# IDEIOW0# STOP0# host IDEIOR0# HDMARDY0# hostIDEIRDY0 DSTROBE0 device IDEDATA150 device IDEADDR20 IDEIORDY0 DDMARDY0 device DevicetUI IDEDACK0# hostIDEIOW0# STOP0# host IDEIOR0# HSTROBE0# host IDEDATA150 At host IDEIOR0# HSTROBE0# at device HSTROBE0#At host IDEDATA150 at device IDEIOR0# HSTROBE0# IDEDREQ0 device IDEDACK0# host IDEIOW0# STOP0# hostIDEIORDY0# DDMARDY0# 414 IDEDACK0# host IDEIORDY0# DDMARDY0# deviceIDEDATA150 host IDEADDR20 IDECS01# AMD Geode SC1200/SC1201 Processor Data Book 415 416 IDEDREQ0 device IDEDACK0 host IDEIOW0# STOP0# hostIDEDATA150 host IDECS01# IDEADDR20 Low Speed Source Note Universal Serial Bus USB 31. USB Timing ParametersFull Speed Receiver EOP Width Note Receiver data jitter tolerance for paired Source EOP widthHost upstream Low Speed Receiver EOP Width Note Differential Data Lines Crossover Points 2.0 Rise Time Fall TimeDifferential Data Lines Consecutive Transitions EOP Width Differential Data to SE0 SkewData Crossover Level Differential Crossover Points Data Lines SIR signal pulse width Modulation signal periodTCPN + Transmitter Sharp-IR and Consumer Remote Control Setting of the Rxhsc bit bit 5 of the Rccfg register FIR Fast IR Port Timing 33. Fast IR Port Timing ParametersMIR Busy ACK# STB# Unit Comments Symbol Parameter Min35. Enhanced Parallel Port Timing Parameters AFD# 36. ECP Forward Mode Timing ParametersExtended Capabilities Port ECP Timing Busy 37. ECP Reverse Mode Timing Parameters BUSY# Sync inactive to Bitclk startup 162.8 Delay Audio Interface Timing AC97 38. AC Reset Timing ParametersAC97RST# inactive to Bitclk 162.8 Startup delay AC97RST# active low pulse width 40. AC97 Clocks Parameters AC97CLK Vold 41. AC97 I/O Timing Parameters SDATAOUT/SYNC SDATAIN, SDATAIN2 42. AC97 Signal Rise and Fall Timing Parameters Slot 43. AC97 Low Power Mode Timing ParametersEnd of Slot 2 to Bitclk Sdatain low Bitclk Sdataout 44. PWRBTN# Timing Parameters Power ManagementPower management event to ONCTL# Assertion ONCTL# PWRBTN# PWRBTN# ONTCL# PWRCNT21 POR# POR# 32KHZ 434 Jtag Interface 48. Jtag Timing Parameters TDI, TMS setup timeNon-test inputs setup time TDI, TMS hold time TDI TMS TDO Output SignalsInput Signals 436 Case-to-Ambient Thermal Resistance Example @ 85C Thermal CharacteristicsΘJC ×C/W Assume P max = 5W and TA max = 40C Therefore Heatsink ConsiderationsExample Assume P max = 9W and TA max = 40C Therefore AMD Geode SC1200/SC1201 Processor Data Book 439 Physical DimensionsPackage Specifications BGU481 Package Bottom View 440 Ordering Part Number Core Frequency Order InformationMacrovision Product Notice MHz Revision # Revisions / Comments Data Book Revision HistoryTable A-1. Revision History

32579B

9.2.8INUSB DC Characteristics

Symbol

Comments

Single Ended Receiver

Threshold

Figure 9-1. Differential Input Sensitivity for Common Mode Range

9.2.9OAC97 DC Characteristics

Symbol

Comments

9.2.10ODn DC Characteristics

Symbol

Comments