AMD SC1201, SC1200 manual High-Resolution Timer Registers, Offset 05h-07h

General Configuration Block 32579B

Table 4-3. WATCHDOG Registers (Continued)

Bit	Description
Offset 04h	WATCHDOG Status Register - WDSTS (R/WC)	Reset Value: 00h

This register contains WATCHDOG status information.

7:4 Reserved. Write as read.

3WDRST (WATCHDOG Reset Asserted). (Read Only) This bit is set to 1 when WATCHDOG Reset is asserted. It is set to 0 when POR# is asserted, or when the WDOVF bit is set to 0.

2WDSMI (WATCHDOG SMI Asserted). (Read Only) This bit is set to 1 when WATCHDOG SMI is asserted. It is set to 0 when POR# is asserted, or when the WDOVF bit is set to 0.

1WDINT (WATCHDOG Interrupt Asserted). (Read Only) This bit is set to 1 when the WATCHDOG Interrupt is asserted. It is set to 0 when POR# is asserted, or when the WDOVF bit is set to 0.

0WDOVF (WATCHDOG Overflow). This bit is set to 1 when the WATCHDOG Timer reaches 0. It is set to 0 when POR# is asserted, or when a 1 is written to this bit by software. Other system reset sources do not affect this bit.

Offset 05h-07h Reserved - RSVD

4.4High-Resolution Timer

The SC1200/SC1201 processor provides an accurate time value that can be used as a time stamp by system soft- ware. This time is called the High-Resolution Timer. The length of the timer value can be extended via software. It is normally enabled while the system is in the C0 and C1 states. Optionally, software can be programmed to enable use of the High-Resolution Timer during C3 state and/or S1 state as well. In all other power states the High-Resolu- tion Timer is disabled.

4.4.1Functional Description

The High-Resolution Timer is a 32-bit free-running count- up timer that uses the oscillator clock or the oscillator clock divided by 27. Bit TMCLKSEL of the TMCNFG register (Offset 0Dh[1]) can be set via software to determine which clock should be used for the High-Resolution Timer.

When the most significant bit (bit 31) of the timer changes from 1 to 0, bit TMSTS of the TMSTS register (Offset 0Ch[0]) is set to 1. When both bit TMSTS and bit TMEN (Offset 0Dh[0]) are 1, an interrupt is asserted. Otherwise, the interrupt is de-asserted. This interrupt enables software emulation of a larger timer.

The High-Resolution Timer interrupt is routed to an IRQ signal. The IRQ signal is programmable via the INTSEL register (Offset 38h). For more information about this regis- ter, see section Section 4.2 "Pin Multiplexing, Interrupt Selection, and Base Address Registers" on page 72.

System software uses the read-only TMVALUE register (Offset 08h[31:0]) to read the current value of the timer. The TMVALUE register has no default value.

The input clock (derived from the 27 MHz crystal oscillator) is enabled when:

•The GX1 module’s internal SUSPA# signal is 1.

or

•The GX1 module’s internal SUSPA# signal is 0 and bit TM27MPD (Offset 0Dh[2]) is 0.

The input clock is disabled, when the GX1 module’s inter- nal SUSPA# signal is 0 and the TM27MPD bit is 1.

For more information about signal SUSPA# see Section

4.4.2.1"Usage Hints" on page 81 and the AMD Geode™ GX1 Processor Data Book.

The High-Resolution Timer function resides on the internal Fast-PCI bus and its registers are in General Configuration Block address space. Only one complete register should be accessed at-a-time (e.g., DWORD access should be used for DWORD wide registers and byte access should be used for byte-wide registers).

4.4.2High-Resolution Timer Registers

Table 4-4 on page 82 describes the registers for the High- Resolution Timer (TIMER).

4.4.2.1Usage Hints

•SMM code should set bit 2 of the TMCNFG register to 1 when entering ACPI C3 state if the High-Resolution Timer should be disabled. If this is not done, the High- Resolution Timer is functional during C3 state.

•SMM code should set bit 2 of the TMCNFG register to 1 when entering ACPI S1 state if the High-Resolution Timer should be disabled. If this is not done, the High- Resolution Timer is functional during S1 state.

AMD Geode™ SC1200/SC1201 Processor Data Book 81