AMD SC1201, SC1200 manual Offset 14h-17h GPDI1 Gpio Data In 1 Register RO, Reserved. Must be set to

Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0 32579B

Table 6-30. F0BAR0+I/O Offset: GPIO Configuration Registers (Continued)

Bit	Description
Offset 10h-13h		GPDO1 — GPIO Data Out 1 Register (R/W)	Reset Value: FFFFFFFFh

31:0

GPIO Data Out. Bits [31:0] of this register correspond to GPIO63-GPIO32 signals, respectively. The value of each bit deter- mines the value driven on the corresponding GPIO signal when its output buffer is enabled. Writing to the bit latches the written data unless the bit is locked by the GPIO Configuration register Lock bit (F0BAR0+I/O Offset 24h[3]). Reading the bit returns the value, regardless of the signal value and configuration.

0:Corresponding GPIO signal driven to low when output enabled.

1:Corresponding GPIO signal driven or released to high (according to buffer type and static pull-up selection) when output enabled.

Offset 14h-17h GPDI1 — GPIO Data In 1 Register (RO) Reset Value: FFFFFFFFh

31:0

GPIO Data In. Bits [31:0] of this register correspond to GPIO63-GPIO32 signals, respectively. Reading each bit returns the value of the corresponding GPIO signal, regardless of the signal configuration and the GPDO1 register (F0BAR0+I/O Offset 10h) value. Writes to this register are ignored.

0:Corresponding GPIO signal level low.

1:Corresponding GPIO signal level high.

Offset 18h-1Bh		GPIEN1 — GPIO Interrupt Enable 1 Register (R/W)	Reset Value: 00000000h
31:16	Reserved. Must be set to 0.
15:0	GPIO Power Management Event (PME) Enable. Bits [15:0] of this register correspond to GPIO47-GPIO32 signals,
	respectively. Each bit allows PME generation by the corresponding GPIO signal.

0:Disable PME generation.

1:Enable PME generation.

Notes: 1) All of the enabled GPIO PMEs are always reported at F1BAR1+I/O Offset 10h[3].

2)Any enabled GPIO PME can be selected to generate an SCI or SMI at F1BAR1+I/O Offset 0Ch[0].

If SCI is selected, the individually selected GPIO PMEs are globally enabled for SCI generation at F1BAR1+I/ O Offset 12h[3] and the status is reported at F1BAR1+I/O Offset 10h[3].

If SMI is selected, the individually selected GPIO PMEs generate an SMI and the status is reported at F1BAR0+I/O Offset 00h/02h[0].

Offset 1Ch-1Fh		GPST1 — GPIO Status 1 Register (R/W1C)	Reset Value: 00000000h
31:16	Reserved. Must be set to 0.
15:0	GPIO Status. Bits [15:0] correspond to GPIO47-GPIO32 signals, respectively. Each bit reports a 1 when hardware detects
	the edge (rising/falling on the GPIO signal) that is programmed in F0BAR0+I/O Offset 24h[5]. If the corresponding bit in
	F0BAR0+I/O Offset 18h is set, this edge generates a PME.

0:No active edge detected since the bit was last cleared.

1:Active edge detected.

Writing 1 to the a Status bit clears it to 0.

This is the third level of SMI status reporting to the second level at F0 Index 87h/F7h[7] and the top level at F1BAR0+I/O Offset 00h/02h[0]. Clearing the third level also clears the second and top levels.

This is the second level of SCI status reporting to the top level at F1BAR1+Offset 10h[3]. The status must be cleared at both the this level and the top level (i.e., the top level is not automatically cleared when a bit in this register is cleared).

Offset 20h-23h GPIO Signal Configuration Select Register (R/W) Reset Value: 00000000h

31:6

Reserved. Must be set to 0.

AMD Geode™ SC1200/SC1201 Processor Data Book 225