Electrical Specifications

32579B

9.3.11Serial Port (UART)

Table 9-32. UART, Sharp-IR, SIR, and Consumer Remote Control Timing Parameters

Symbol

Parameter

Min

Max

Unit

Comments

 

 

 

 

 

 

tBT

Single bit time in UART and

tBTN - 25

tBTN + 25

ns

Transmitter

 

Sharp-IR

(Note 1)

 

 

 

 

 

 

 

 

 

 

 

tBTN - 2%

tBTN + 2%

ns

Receiver

tCMW

Modulation signal pulse width in

tCWN - 25

tCWN + 25

ns

Transmitter

 

Sharp-IR and Consumer

(Note 2)

 

 

 

 

Remote Control

 

 

 

 

 

500

 

ns

Receiver

 

 

 

 

 

 

 

 

 

tCMP

Modulation signal period in

tCPN - 25

tCPN + 25

ns

Transmitter

 

Sharp-IR and Consumer

(Note 3)

 

 

 

 

Remote Control

 

 

 

 

 

tMMIN

tMMAX

ns

Receiver

 

 

 

 

(Note 4)

(Note 4)

 

 

 

 

 

 

 

 

tSPW

SIR signal pulse width

(3/16) x tBTN - 15

(3/16) x tBTN + 15

ns

Transmitter, Variable

 

 

(Note 1)

(Note 1)

 

 

 

 

 

 

 

 

 

 

1.48

1.78

µs

Transmitter, Fixed

 

 

 

 

 

 

 

 

1

 

µs

Receiver

 

 

 

 

 

 

SDRT

SIR data rate tolerance % of

 

± 0.87%

 

Transmitter

 

nominal data rate

 

 

 

 

 

 

± 2.0%

 

Receiver

 

 

 

 

 

 

 

 

 

 

tSJT

SIR leading edge jitter % of

 

± 2.5%

 

Transmitter

 

nominal bit duration

 

 

 

 

 

 

± 6.5%

 

Receiver

 

 

 

 

 

 

 

 

 

 

Note 1. tBTN is the nominal bit time in UART, Sharp-IR, SIR and Consumer Remote Control modes. It is determined by the setting of the Baud Generator Divisor registers.

Note 2. tCWN is the nominal pulse width of the modulation signal for Sharp-IR and Consumer Remote Control modes. It is determined by the MCPW field (bits [7:5]) of the IRTXMC register and the TXHSC bit (bit 2) of the RCCFG register.

Note 3. tCPN is the nominal period of the modulation signal for Sharp-IR and Consumer Remote Control modes. It is deter- mined by the MCFR field (bits [4:0]) of the IRTXMC registerand the TXHSC bit (bit 2) of the RCCFG register.

Note 4. tMMIN and tMMAX define the time range within which the period of the incoming subcarrier signal has to fall in order for the signal to be accepted by the receiver. These time values are determined by the contents of register IRRXDC

and the setting of the RXHSC bit (bit 5) of the RCCFG register.

tBT

UART

tCMP

Sharp IR tCMW

Consumer

Remote

Control

tSPW

SIR

Figure 9-42. UART, Sharp-IR, SIR, and Consumer Remote Control Timing Diagram

AMD Geode™ SC1200/SC1201 Processor Data Book

421

Page 421
Image 421
AMD SC1201, SC1200 manual Single bit time in Uart, Transmitter, Sharp-IR, Modulation signal period, SIR signal pulse width