AMD SC1200, SC1201 manual Video Processor Support Registers F4BAR0, Reserved 338

32579B	Video Processor Module - Video Processor Registers - Function 4
7.3.2.1 Video Processor Support Registers - F4BAR0
F4 Index 10h, Base Address Register 0 (F4BAR0) sets the	Note: Reserved bits that are not defined as “must be set
base address that allows PCI access to the Video Proces-	to 0 or 1" should be written with a value that is read
sor support registers, not including VIP. A separate base	from them.
address register (F4BAR2) is used to access VIP support
registers (see Section 7.3.2.2 on page 359).

Table 7-9. F4BAR0+Memory Offset: Video Processor Configuration Registers

Bit	Description
Offset 00h-03h			Video Configuration Register (R/W)	Reset Value: 00000000h
Configuration register for options of the motion video acceleration hardware.
31:29	Reserved. Must be set to 0.
28	EN_42X (Enable 4:2:x Format). Allows format selection.
	0:	4:2:2 format.
	1:	4:2:0 format.
	Note: When input video stream is RGB (i.e., F4BAR0+Memory Offset 4Ch[13] = 1), this bit must be set to 0.
27	BIT_8_LINE_SIZE. When enabled, this bit increases line size from VID_LIN_SIZ (bits [15:8]) DWORDs by adding 256
	DWORDs.
	0:	Disable.
	1:	Enable.
26:25	Reserved. Must be set to 0.
24:16	INIT_RD_ADDR (Initial Buffer Read Address). This field preloads the starting read address for the line buffers at the
	beginning of each display line. It is used for hardware clipping of the video window at the left edge of the active display. It
	represents the DWORD address of the source pixel which is to be displayed first.
	For an unclipped window, this value should be 0. For 4:2:0 format, set bits [17:16] to 00.
15:8	VID_LIN_SIZ (Video Line Size). Represents the number of DWORDs that make up the horizontal size of the source video
	data.
7	YFILT_EN (Y Filter Enable). Enables/disables the vertical filter.
	0: Disable. Upscaling done by repeating pixels.
	1: Enable. Upscaling done by interpolating pixels.
	Note: This bit is used with Y upscaling logic. Reset to 0 when not required.
6	XFILT_EN (X Filter Enable). Enables/disables the horizontal filter.
	0: Disable. Upscaling done by repeating pixels.
	1: Enable. Upscaling done by interpolating pixels.
	Note: This bit is used with X upscaling logic. Reset to 0 when not required.
5:4	Reserved.
3:2	VID_FMT (Video Format). Byte ordering of video data on the Video Input bus (VPD[7:0]). The interpretation of these bits
	depends on the settings of bit 13 (GV_SEL) in the Video De-Interlacing and Alpha Control register (F4BAR0+Memory Offset
	4Ch) and bit 28 (EN_42X) of this register.
	If GV_SEL = 0 and EN_42X = 0:
	00: Cb Y0 Cr Y1		10: Y0 Cb Y1 Cr
	01: Y1 Cr Y0 Cb		11: Y0 Cr Y1 Cb
	If GV_SEL = 0 and EN_42X = 1:
	00: Y0 Y1 Y2 Y3		10: Y1 Y0 Y3 Y2
	01: Y3 Y2 Y1 Y0		11: Y1 Y2 Y3 Y0
	If GV_SEL = 1 and EN_42X = 0:
	00: P1L P1M P2L P2M		10: P1M P1L P2M P2L
	01: P2M P2L P1M P1L		11: P1M P2L P2M P1L
	If GV_SEL = 1 and EN_42X = 1: Reserved
	Note: Both RGB 5:6:5 and YUV 4:2:2 contain two pixels in each 32-bit DWORD. YUV 4:2:0 contains a stream of Y data
		for each line, followed by U and V data for that same line.
1	Reserved.
338			AMD Geode™ SC1200/SC1201 Processor Data Book