TROUBLESHOOTING
In case of trouble, first check the following list. What seems to be a failure of the unit is sometimes due to imperfect maintenance, defective discs, or mistakes made during unfamiliar operations. Such troubles are often solved by correcting simple mistakes or by simple maintenance operations. If your trouble cannot be resolved even after checking the following list, please call you nearest HHB service center or station.
Self-diagnostics
This unit incorporates a
When it detects trouble during an operation, it displays one of the following messages on the display panel.
Display | Cause |
| Treatment |
| Reference |
|
| Page | |||
|
|
|
|
| |
Alternate display of | The disc is stopped due to dirt, stains, |
| Take out the disc and check for dirt, dust, scratches, etc. If |
| page 22 |
"CHECK and "DISC" | scratches or vibration. |
| the disc is damaged, it may be necessary to change it. |
|
|
| The disc may be loaded upside down. |
| Take out and check the disc. |
| page 44 |
|
|
|
|
|
|
|
|
| If the same message is displayed again after the disc is |
|
|
|
|
| reloaded, unplug the power cord and plug it in again. |
|
|
|
|
| If the same message is displayed again, please contact a HHB |
|
|
|
|
| authorized service center. |
|
|
|
|
|
|
|
|
Display blinks "CHECK" | A system error occurred, perhaps due to |
| Unplug the power cord and plug it in again. |
|
|
noise or static electricity. |
| If the same messages are displayed again, please contact a |
|
| |
|
|
|
| ||
|
|
| HHB authorized service center. |
|
|
|
|
|
|
|
|
Information messages related to recording operation
Display | Cause | Treatment | Reference | |
Page | ||||
|
|
| ||
|
|
|
| |
Cyclic display of | The source player is already playing | Stop playing the source player. | page 54 | |
"CHECK", "INPUT" | when the DIGITAL SYNCHRO button is | In a while, | page 58 | |
and "CD ?" | pressed. | set to the synchro recording standby mode. | page 60 | |
|
|
|
| |
Alternate display of | The unit is making preparations for | When this message disappears, normal operation is possible. |
| |
"SET" and "UP" | recording. |
|
| |
"REPAIR" | Because the disc was left in the unit after | While "REPAIR" is displayed, the track number and recording |
| |
| recording and the power plug was | time data are repaired by tracking the recorded area. Further |
| |
| unplugged later, the track number and | recording or finalization is possible when the display returns |
| |
| recording time data have been cleared | to the previous condition. |
| |
| without being recorded on the disc. | Tracking the recorded area takes about 40 minutes if the disc |
| |
|
| has been fully recorded. |
| |
"REC FULL" | No more recording is possible because | Replace the disc with a new one. | page 48 | |
| the available recording time of the disc | Erase a | page 88 | |
| has been completely used or 99 tracks |
|
| |
| have already been recorded on the disc. |
|
| |
|
|
|
| |
"STAND BY" | An attempt is made to begin recording | Wait approximately 1 minute for the setup to be completed, |
| |
| within approximately 1 minute after | and then |
| |
| turning the power to ON. |
|
| |
|
|
|
|
Information messages related to playback operation
Display | Cause | Treatment | Reference | |
Page | ||||
|
|
| ||
|
|
|
| |
“NEW DISC” | A blank disc is loaded. | Recording is possible but playback is not. | page 20 | |
| An attempt is made to play a blank disc. |
| page 44 | |
|
|
|
| |
“NO DISC” | An attempt is made to start playback | Open the tray and check if a disc is loaded. | page 44 | |
| without loading a disc. |
|
| |
|
|
|
| |
“RESUME” | The unit is resuming an operation. After | Wait until the message disappears. | page 74 | |
| the power supply is cut off by power |
| page 86 | |
| failure or by mistake during recording, |
|
| |
| the unit enters RESUME mode so that |
|
| |
| additional recording is possible. |
|
| |
|
|
|
|
118
