APC AXFA11G Size 2200 mm 88 in. to 2600 mm 104, Repeatability, Maximum Power Consumption

Size 2200 mm (88 in.) to 2600 mm (104 in.)

%of Rate 2.4

	2.0
	1.6
Pulse	1.2			HighStandardgr eAccuracyA curacy
Output
Accuracy 0.85
	0.8
	0.4
	0
	0	1	2	6	8	10
				V[m/s]		F16-3.EPS

Current Output: Pulse output accuracy plus ±0.05% of Span

Repeatability:

±0.1% of Rate (V ≧ 1 m/s (3.3 ft/s))

±0.05% of Rate ±0.5 mm/s (V < 1 m/s (3.3 ft/s))

Maximum Power Consumption:

Combined with AXF Remote Flowtube: 20 W

Insulation Resistance(*1) :

Between power supply terminals and ground terminal: 100MΩ at 500V DC

Between power supply terminals and input/output/ excitation current terminals : 100MΩ at 500V DC Between ground terminal and input/output/excitation current terminals: 20MΩ at 100V DC

Between input/output/excitation current terminal: 20MΩ at 100V DC

Withstand Voltage(*1) :

Between power supply terminals and ground terminal: 1390V AC for 2 seconds

Between power supply terminals and input/output terminals: 1390V AC for 2 seconds

Between excitation current terminal and ground terminal: 160V AC for 2 seconds

Between excitation current terminal and input /output terminals: 200V AC for 2 seconds

CAUTION

*1: When performing the Insulation Resistance Test or the Withstand Voltage Test, please obey the following caution.

•Following the relevant test, wait for more than 10 seconds after the power supply has been turned off before removing the cover.

•Remove all wires from terminals before testing.

•When the power terminal has a lighting protector (optional code A), remove the short bar at the ground terminal.

•After testing, be sure to discharge by using a resistance and return all wires and the short bar to its correct position.

•Screws must be tightened to a torque of 1.18 N-m or more.

•After closing the cover, the power supply can be restored.

11. OUTLINE

Safety Requirement Standards:

EN61010-1

•Altitude at installation site: Max. 2000 m above sea level

•Installation category based on IEC1010:

Overvoltage category II (“II” applies to electrical equip- ment which is supplied from a fixed installation-like distribution board.)

•Pollution degree based on IEC1010

Pollution degree 2 (“Pollution degree” describes the degree to which a solid, liquid, or gas which deteriorates dielectric strength or surface resistivity is adhering. “2” applies to a normal indoor atmosphere.)

EMC Conformity Standards:

EN61326

EN61000-3-2, EN61000-3-3

AS/NZS CISPR11

■NORMAL OPERATING CONDITIONS

Ambient Temperature: –40°C to +60°C (–40°F to +140°F) Indicator’s operating range: –20°C to +60°C (–4°F to +140°F)

Ambient Humidity: 0 to 100%

Lengthy continuous operation at 95% or more is not recommended.

Power Supply:

Power supply code 1:

•AC specifications

Rated power supply: 100 to 240 V AC, 50/60 Hz

(Operating voltage range: 80 to 264 V AC)

•DC specifications

Rated power supply: 100 to 120 V DC

(Operating voltage range: 90 to 130 V DC)

Power supply code 2:

•AC specifications

Rated power supply: 24 V AC, 50/60 Hz

(Operating voltage range: 20.4 to 28.8 V AC)

•DC specifications

Rated power supply: 24 V DC

(Operating voltage range: 20.4 to 28.8 V DC)

Supplied Power and

Cable Length for Power Supply Code 2

m(ft)	420	(1380)
length
	280	(	920)
cable
	200 (		660)
Allowable	100	(	330)
			0	22	24	26	28.8
			20.4

Usable range E (V)

Cable cross section area: 1.25 mm2

Cable cross section area: 2 mm2

F00.EPS

Vibration Conditions:

Level of vibration in conformity with IEC 60068-2-6 (SAMA31. 1-1980)

0.5 G or less (frequency 500 Hz or less)

Note: Avoid locations with much vibration (with a vibration frequency of 500 Hz or more), which may cause damage to the equipment.

11-4 IM 01E20C01-01E