Checking for Problems, Setting Parameters | APC AXFA11G manual

8. OPERATION VIA HART COMMUNICATOR

NOTE

Data changed with the HART Communicator is sent to the AXFA11 by pressing

SEND (F2) of the HART Communicator.

8.3.3Checking for Problems

The self-diagnostic function of the AXFA11 is explained in Section 6.5 “Alarm Functions” By using the HART Communicator, it is also possible to carry out this function in the “Test/Status” parameter. Test for each error.

* Open the “Test/Status” setting display.

1.Device Setup 2. Diag/Service 3. Test/Status

8.3.4Setting Parameters

As mentioned in Section 5.2.2 “Setting Mode,” the AXFA11’s parameters are divided into three types:

i.Selection type

ii.Numeric type

iii.Alphanumeric type

This section describes how to set these parameters using a HART communicator.

NOTE

All three parameters must be set to obtain a correct signal.

Nominal size, flow rate span and meter factor must be set.

8.3.4.1Example of Setting Selection-Type Data: Base Flow Unit

This example describes the setting of the flow rate units for the selection-type parameter “Base Flow Unit” from m3 to l (Liter).

Open the “Base Flow Unit” setting display.

1. Device Setup 3. Easy Setup 3. Base Flow Unit

1AXFA11 : FI-1100 Base Flow Unit

m3

m3

K1(Kiloliter)

l(Liter)

cm3

ESC ENTER

2AXFA11 : FI-1100 Easy Setup

1 Language


2	PV	Damping
3	Base		Flow Unit	l
4	Base		Time Unit	/h
5	PV	Span

SEND HOME

⋅Select “1(Liter)”.

2

F4	Press ENTER (F4).

(ENTER)

3AXFA11 : FI-1100

Easy Setup

1Language

2PV Damp

F2

Press SEND (F2) to set the data into the AXFA11.

3	Base	Flow Unit	l
4	Base	Time Unit	/h
5	PV Span

SAVE HOME

(SEND)

F0807.EPS

8-6	IM 01E20C01-01E

Image 80

APC AXFA11G user manual Checking for Problems, Setting Parameters, Example of Setting Selection-Type Data Base Flow Unit

Contents

Users ManualAXFA11G Contents Operation VIA Hart Communicator Revision Record Safety and Modification Precautions Introduction Guarantee will not apply in the following cases Using the Magnetic Flowmeter SafelyWarranty Combination Remote Flowtubes Handling Precautions Checking Model and SpecificationsAccessories Storage Precautions Installation Installation LocationMounting Surface Mounting Wall Mounting Inch Pipe Mounting Panel MountingInch pipe Mounting fixture Washer Clamp screw Unit mm approx. inch Panel cutout 203 Mounting fixture 172 Wiring Wiring PrecautionsDedicated Signal Cable Axfc Cables Wiring Ports Excitation Cable/Power Cable/Output CableUnit mm approx. inch Crimp Terminal On the converter side When there are no particular optional specifications Wiring using waterproof glandsConduit Wiring Plastic gland Removing Cover Wiring ConnectionsTerminal Configuration Precautions for Wiring of Power Supply Cables DC Power Connection Wiring the Remote Flowtube with the AXFA11 Converter Axfc Dedicated signal cable Excitation cableGrounding Protective grounding terminals Connecting to External Instru- ments To 20 mA DC Current Output Pulse Output Status Input Status Output / Alarm Output 13 Status Output Connection Data display area Operating Panel Configuration and FunctionsSetting switch operations Content Display itemsReversed-character indication None Display Unit Setting Methods Display Mode → Setting Mode Setting Mode To Parameter Search Mode Setting Example for Selection-Type Data Flow rate units Parameter Setting ProcedureSetting Mode Sub-item Current unit setting Sub-item Parameter Search ModeB21 Base Flow Unit Parameter Sub-item Setting Example for Numeric-Type Data Flow rate span Setting Mode ConditionMajor Item Parameter Search Mode Setting mode B23 Flow Span Setting Example for Alphanumeric-Type Data Tag number Setting Mode ConditionSub-item Parameter Search Mode Major item Incorrect setting Modified value Search Mode Selection CSub-item Major item Parameter Description Item B Menu B Easy Setup items Item a Menu a Display items Indicated item Default value Units Description Display unitName Data range Item C Menu C Basic Setting items Name Data range Position Default value Units Display unit Item D Menu D Total Setting items Default value Units Display unitName Data range Position Default value Display unit Name Item E Menu E Pulse Setting items Item F Menu F Status Functions Setting items Item G Menu G Alarm Setting items ALM-SETTING ALM HYSALM OUT ACT ALM-SIG Over Item H Menu H Display Setting items Item J Menu J Auxiliary Function Setting items Item K Menu K Diagnostic Function Setting items Units Display unit Item N Menu N Loop Test Setting items Item P Menu P Parameter Protection items Menu B Easy Setup items Data Range Example When 1000 m3/h is set for B23/C42 Flow Span Unit/P 10-9 FU u Unit/P 10-6 FU Pulse/s Description Menu C Basic Setting items B41/H11 Display Select2 and B42/H12 Display Meter Factor Settings Menu D Total Setting items C47 User Span Select Selection of the useC49 Flow User Span Is set forB22/C41 Base Time Unit TOTAL, and A32 DIF Total when Brain F13Flow Unit Is set forB22/C41 Base Time E20 Pulse Active Mode Menu E Pulse Setting itemsSetting for E20 Pulse Active Mode Menu F Status Functions Setting items Setting Function DescriptionSwitch Lower and D24 Ttl Switch Upper G33 Alm-HH/LL to Yes No Function No input function Val Upper Multiple ranges setting Multiple Ranges Setting Automatic multiple ranges switchingStatus Output for Automatic Multiple Ranges Switching 1 Status Output for Automatic Multiple Ranges Switching Parameter setting sequence For automatic multiple ranges switchingF14 SO1/2 Active Mode F10 SO1 Function F11 SO2 Function 2 Multiple Ranges Switching via External Status Input F15 G11 High Alarm High alarm setting Menu G Alarm Setting itemsG10 Low Alarm Low alarm setting High High Alarm 100 High Alarm100 High Alarm Instantaneous flow rate Low Low Alarm Time t Output Example 100 85% 75% High Alarm 35% Low Alarm100 25% Setting Function ExampleG22 4-20mA Burn Out Display of the current ClosedOn OpenOff G41 Alm Record1 Alarm record1 Alarm ItemsG43 Alm Record2 Alarm record2 G45 Alm Record3 Alarm record3 Menu J Auxiliary Function Setting items Setting range 0 to 10% Hysteresis Function or Determining rate limit value and dead timeExample 1 Step input Example 2 Slurry noise J31 Power Frequency Menu K Diagnostic Function Setting itemsK10 Adhesion Check Setting of adhesion Power Supply Code 100 to 240 V AC or 100 to 120 V DC Adhesion Diagnostic Function Menu M Automatic Zero Adjustment Function Setting itemsMenu N Loop Test Setting items SO1 Function or F11 SO2 Function, then N11 Test Output Value Setting for test output Default setting EnableMenu P Parameter Protection items Write Protect function Default setting After password setting Out Act Mode G20 Alm Out Act Mode Setting of the activeDisplay and output condition for process alarms Display and output condition for setting alarm occurrences Alarm description SelectionTotali Pulse Display Alarm Output Unit Alarms & Warning Messages K12, K13 and K14 are correct Operation VIA Brain Terminal BT200 BT200 Basic OperationsKey Descriptions Key Layout and Display Key-in Sequence Command FunctionFunction Keys 1 BT200 Connection AXFA11 Operation Using a BT200Data update and upload/ download function of BT200 Parameter Setting Using a BT200 3 BT200 Screens & Flow Rate Data Display B21 Flow UNIT, press 1 BT200 Setting of Selection-Type Data Flow rate unitsMoved to B Easy Setup 2 BT200 Setting of Numeric-Type Data Flow rate span B23 Flow SPAN, press Moved to C Basic Setup 3 BT200 Setting of Alphanumeric-Type Data Tag numberTo C Basic Setup Operation VIA Hart Communicator Specifications for Communication Line Conditions of Communication LineInterconnectwion between AXFA11 and Hart Communicator Communication Line Requirements Basic Operation of the Hart Communicator Model Keys and Functions Key Operation DisplayCalling Up Menu Addresses Entering, Setting and Sending Data Parameter ConfigurationParameters Data Renewing Example of Setting Selection-Type Data Base Flow Unit Checking for ProblemsSetting Parameters Example of Setting Numeric-Type Data PV Span PV Span Example of Setting Alphanumeric-Type Data Tag Number Display Example 1 of Other Settings Meter Factor Select MF Set Select Power Frequency Example 3 of Other Settings Trim Analog Output Trim Returning fld dev to original output appears Select the Scaled D/A trim Returning fld dev to original output appears Example 4 of Other Settings Burst Mode Setting of Burst ModeExiting Burst Mode Example 5 of Other Settings Multidrop Mode Polling Exiting Multidrop Mode Example 6 of Other Settings Write Protection Setting Password Open Wrt Protect Menu in the Hot key Menu Changing Password Enable Wrt 10min Joker password and Software Seal Other Functions and Operations Menu Tree On next E12 J24 J30 P22 P23 Pre-operation Zero Adjustment Actual Operation Zero Adjustment Using Display Unit Switches Selection D Major item Sub- item selection D Zero Adjustment via External Status Input Ext Auto Zero Maintenance Components ReplacementDisplay Unit Replacement Fuse Replacement Setting of Switches Amplifier ReplacementSetting of Burnout Switch Output Setting Pins for Burnout Setting of Write Protect Switch 4 Switch Configuration Troubleshooting No Indication Unstable Zero Start Disagreement Between Indication and Actual Flow Outline 65 10 Cf 10,000 How to Set Parameters Functions Standard Performance Maximum Power Consumption Safety Requirement StandardsPower Supply Power supply code Size 2200 mm 88 in. to 2600 mm 104 Accessories Optional Specifications for AXFA11 Remote Converter Terminal Wiring Remote Converter AXFA11G Surface mounting Remote Converter AXFA11G /RK AM11 Replacement Bracket General tolerance in the dimensional outline drawing Dedicated Signal Cable AXFC-4-L AXFC-0-L Revision Record Edition Date Revised item