●Remote Converter AXFA11G /RK (AM11 Replacement Bracket)
Pipe mounting
180(7.09) | 133.5(5.26) | |
| (Surface mounting hole) |
|
65(2.56) | 210(8.27) |
|
11. OUTLINE
194(7.64)
31 31 31 31
(1.22) (1.22) (1.22) (1.22)
(80.5)
(3.17)
49 |
| (1.93) | ||
| ||||
|
|
| ||
| 29 |
|
| (0.94) (1.14) |
24 |
|
| ||
(80.5) |
|
| ||
| (3.17) | |||
|
|
|
|
|
Bracket for replacement (For pipe mounting)
Surface mounting
(190)
(7.48)
Mouting Screw*1 18(0.71)
| (126.5) | (4.98) | *1: These screws must be | |
|
|
| ||
|
|
| * provided by the user. | |
(62) | Bracket for replacement | |||
(For surface mounting) | ||||
(2.44) | ||||
|
|
| ||
FF0AXFA11E.EPS
●Unless otherwise specified, difference in the dimensions are refer to the following table.
|
|
| General tolerance in the dimensional outline drawing. |
| Unit : mm (approx.inch) | |||||||
|
|
|
|
|
|
|
|
|
|
| ||
Category of basic dimension | Tolerance |
| Category of basic dimension |
| Tolerance | |||||||
Above | Equal or below |
| Above | Equal or below |
| |||||||
|
|
|
|
| ||||||||
|
| 3 | (0.12) | 0.7 (0.03) |
| 500 | (19.69) | 630 | (24.80) |
| 5.5 (2.17) | |
3 | (0.12) | 6 | (0.24) | 0.9 (0.04) |
| 630 | (24.80) | 800 | (31.50) |
| 6.25 (0.25) | |
6 | (0.24) | 10 | (0.39) | 1.1 (0.04) |
| 800 | (31.50) | 1000 | (39.37) |
| 7.0 (0.28) | |
10 | (0.39) | 18 | (0.71) | 1.35 (0.05) |
| 1000 | (39.37) | 1250 | (49.21) |
| 8.25 (0.32) | |
18 | (0.71) | 30 | (1.18) | 1.65 (0.06) |
| 1250 | (49.21) | 1600 | (62.99) |
| 9.75 (0.38) | |
30 | (1.18) | 50 | (1.97) | 1.95 (0.08) |
| 1600 | (62.99) | 2000 | (78.74) |
| 11.5 (0.45) | |
50 | (1.97) | 80 | (3.15) | 2.3 (0.09) |
| 2000 | (78.74) | 2500 | (98.43) |
| 14.0 (0.55) | |
80 | (3.15) | 120 | (4.72) | 2.7 (0.11) |
| 2500 | (98.43) | 3150 (124.02) |
| 16.5 (0.65) | ||
120 | (4.72) | 180 | (7.09) | 3.15 (0.12) |
|
|
|
|
|
|
| |
180 | (7.09) | 250 | (9.84) | 3.6 | (0.14) |
|
|
|
|
|
|
|
250 | (9.84) | 315 (12.40) | 4.05 | (0.16) |
|
|
|
|
|
|
| |
315 (12.40) | 400 (15.75) | 4.45 | (0.18) |
|
|
|
|
|
|
| ||
400 (15.75) | 500 (19.69) | 4.85 | (0.19) |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
Remarks: The numeric is based on criteria of tolerance class IT18 in JIS B 0401.
IM |
