Select Power Frequency | APC AXFA11G guide

8. OPERATION VIA HART COMMUNICATOR

8.3.4.5Example 2 of Other Settings: Power Frequency (For DC version only)

IMPORTANT

In situation where a DC power supply is used for converters, set the local com- mercial power frequency in area where the converter is lnstalled. The flowmeter is set to 50.00 Hz at the factory.

Set “No” forPower“ Synch” and the local commercial power frequency for “Power Frequency”.

Open the “Power freq” setting display:

1. Device Setup 4. Detailed Setup 4. Function Set 5. Aux Power Frequency

⋅ 9

1

AXFA11 : FI-1201

Select “Power Frequency”.

Aux

6

Dead Time

Os

7

Pulsing Flow

No

8

T/P Damp Select

9

Power Synch

No

Power Frequency

SAVE

HOME

2AXFA11 : FI-1201 Power Frequency

50.00Hz

DEL ESC ENTER

3AXFA11 : FI-1201 Power Frequency 50.00 60.00

DEL ESC ENTER

4AXFA11 : FI-1201

Aux
6		Dead Time	Os
7		Pulsing Flow	No
8		T/P Damp Select
9		Power Synch	No
		Power Frequency

SAVE HOME

‘60.0’

F4

(ENTER)

F2

(SEND)

F3

(HOME)

Enter “60.00” with alphanumeric keys.

Press ENTER (F4).

Press SEND (F2) to set the data into the AXFA11.

Press HOME (F3), and return to the “Online” menu.

F0813.EPS

8-10	IM 01E20C01-01E

Image 84

APC AXFA11G user manual Select Power Frequency

Contents

Users ManualAXFA11G Contents Operation VIA Hart Communicator Revision Record Safety and Modification Precautions Introduction Using the Magnetic Flowmeter Safely WarrantyGuarantee will not apply in the following cases Combination Remote Flowtubes Handling Precautions Checking Model and SpecificationsAccessories Storage Precautions Installation Installation LocationMounting Surface Mounting Wall Mounting Inch Pipe Mounting Panel MountingInch pipe Mounting fixture Washer Clamp screw Unit mm approx. inch Panel cutout 203 Mounting fixture 172 Wiring Wiring PrecautionsDedicated Signal Cable Axfc Cables Wiring Ports Excitation Cable/Power Cable/Output CableUnit mm approx. inch Crimp Terminal On the converter side When there are no particular optional specifications Wiring using waterproof glandsConduit Wiring Plastic gland Wiring Connections Terminal ConfigurationRemoving Cover Precautions for Wiring of Power Supply Cables DC Power Connection Wiring the Remote Flowtube with the AXFA11 Converter Axfc Dedicated signal cable Excitation cableGrounding Protective grounding terminals Connecting to External Instru- ments To 20 mA DC Current Output Pulse Output Status Input Status Output / Alarm Output 13 Status Output Connection Operating Panel Configuration and Functions Setting switch operationsData display area Content Display itemsReversed-character indication None Display Unit Setting Methods Display Mode → Setting Mode Setting Mode To Parameter Search Mode Parameter Setting Procedure Setting ModeSetting Example for Selection-Type Data Flow rate units Sub-item Current unit setting Sub-item Parameter Search ModeB21 Base Flow Unit Parameter Sub-item Setting Example for Numeric-Type Data Flow rate span Setting Mode ConditionMajor Item Parameter Search Mode Setting mode B23 Flow Span Setting Example for Alphanumeric-Type Data Tag number Setting Mode ConditionSub-item Parameter Search Mode Major item Incorrect setting Search Mode Selection C Sub-item Major itemModified value Parameter Description Item B Menu B Easy Setup items Item a Menu a Display items Default value Units Description Display unit Name Data rangeIndicated item Item C Menu C Basic Setting items Name Data range Position Default value Units Display unit Item D Menu D Total Setting items Default value Units Display unitName Data range Position Default value Display unit Name Item E Menu E Pulse Setting items Item F Menu F Status Functions Setting items Item G Menu G Alarm Setting items ALM-SETTING ALM HYSALM OUT ACT ALM-SIG Over Item H Menu H Display Setting items Item J Menu J Auxiliary Function Setting items Item K Menu K Diagnostic Function Setting items Units Display unit Item N Menu N Loop Test Setting items Item P Menu P Parameter Protection items Menu B Easy Setup items Data Range Example When 1000 m3/h is set for B23/C42 Flow Span Unit/P 10-9 FU u Unit/P 10-6 FU Pulse/s Description Menu C Basic Setting items B41/H11 Display Select2 and B42/H12 Display Meter Factor Settings Menu D Total Setting items C47 User Span Select Selection of the useC49 Flow User Span Is set forB22/C41 Base Time Unit TOTAL, and A32 DIF Total when Brain F13Flow Unit Is set forB22/C41 Base Time Menu E Pulse Setting items Setting for E20 Pulse Active ModeE20 Pulse Active Mode Menu F Status Functions Setting items Setting Function DescriptionSwitch Lower and D24 Ttl Switch Upper G33 Alm-HH/LL to Yes No Function No input function Val Upper Multiple ranges setting Multiple Ranges Setting Automatic multiple ranges switchingStatus Output for Automatic Multiple Ranges Switching 1 Status Output for Automatic Multiple Ranges Switching Parameter setting sequence For automatic multiple ranges switchingF14 SO1/2 Active Mode F10 SO1 Function F11 SO2 Function 2 Multiple Ranges Switching via External Status Input F15 Menu G Alarm Setting items G10 Low Alarm Low alarm settingG11 High Alarm High alarm setting High High Alarm 100 High Alarm100 High Alarm Instantaneous flow rate Low Low Alarm Time t Output Example 100 85% 75% High Alarm 35% Low Alarm100 25% Setting Function ExampleG22 4-20mA Burn Out Display of the current ClosedOn OpenOff G41 Alm Record1 Alarm record1 Alarm ItemsG43 Alm Record2 Alarm record2 G45 Alm Record3 Alarm record3 Menu J Auxiliary Function Setting items Setting range 0 to 10% Hysteresis Function or Determining rate limit value and dead timeExample 1 Step input Example 2 Slurry noise J31 Power Frequency Menu K Diagnostic Function Setting itemsK10 Adhesion Check Setting of adhesion Power Supply Code 100 to 240 V AC or 100 to 120 V DC Adhesion Diagnostic Function Menu M Automatic Zero Adjustment Function Setting itemsMenu N Loop Test Setting items SO1 Function or F11 SO2 Function, then N11 Test Output Value Setting for test output Default setting EnableMenu P Parameter Protection items Write Protect function Default setting After password setting G20 Alm Out Act Mode Setting of the active Display and output condition for process alarmsOut Act Mode Display and output condition for setting alarm occurrences Alarm description SelectionTotali Pulse Display Alarm Output Unit Alarms & Warning Messages K12, K13 and K14 are correct Operation VIA Brain Terminal BT200 BT200 Basic OperationsKey Descriptions Key Layout and Display Command Function Function KeysKey-in Sequence AXFA11 Operation Using a BT200 Data update and upload/ download function of BT2001 BT200 Connection Parameter Setting Using a BT200 3 BT200 Screens & Flow Rate Data Display 1 BT200 Setting of Selection-Type Data Flow rate units Moved to B Easy SetupB21 Flow UNIT, press 2 BT200 Setting of Numeric-Type Data Flow rate span B23 Flow SPAN, press 3 BT200 Setting of Alphanumeric-Type Data Tag number To C Basic SetupMoved to C Basic Setup Operation VIA Hart Communicator Specifications for Communication Line Conditions of Communication LineInterconnectwion between AXFA11 and Hart Communicator Communication Line Requirements Basic Operation of the Hart Communicator Model Keys and Functions Display Calling Up Menu AddressesKey Operation Entering, Setting and Sending Data Parameter ConfigurationParameters Data Renewing Checking for Problems Setting ParametersExample of Setting Selection-Type Data Base Flow Unit Example of Setting Numeric-Type Data PV Span PV Span Example of Setting Alphanumeric-Type Data Tag Number Display Example 1 of Other Settings Meter Factor Select MF Set Select Power Frequency Example 3 of Other Settings Trim Analog Output Trim Returning fld dev to original output appears Select the Scaled D/A trim Returning fld dev to original output appears Example 4 of Other Settings Burst Mode Setting of Burst ModeExiting Burst Mode Example 5 of Other Settings Multidrop Mode Polling Exiting Multidrop Mode Example 6 of Other Settings Write Protection Setting Password Open Wrt Protect Menu in the Hot key Menu Changing Password Enable Wrt 10min Joker password and Software Seal Other Functions and Operations Menu Tree On next E12 J24 J30 P22 P23 Pre-operation Zero Adjustment Actual Operation Zero Adjustment Using Display Unit Switches Selection D Major item Sub- item selection D Zero Adjustment via External Status Input Ext Auto Zero Maintenance Components ReplacementDisplay Unit Replacement Fuse Replacement Setting of Switches Amplifier ReplacementSetting of Burnout Switch Output Setting Pins for Burnout Setting of Write Protect Switch 4 Switch Configuration Troubleshooting No Indication Unstable Zero Start Disagreement Between Indication and Actual Flow Outline 65 10 Cf 10,000 How to Set Parameters Functions Standard Performance Maximum Power Consumption Safety Requirement StandardsPower Supply Power supply code Size 2200 mm 88 in. to 2600 mm 104 Accessories Optional Specifications for AXFA11 Remote Converter Terminal Wiring Remote Converter AXFA11G Surface mounting Remote Converter AXFA11G /RK AM11 Replacement Bracket General tolerance in the dimensional outline drawing Dedicated Signal Cable AXFC-4-L AXFC-0-L Revision Record Edition Date Revised item