Manuals / HP / Computer Equipment / Personal Computer

HP Z800 Sp632up SP632UPABA, FL939UT FL939UT#ABA manual Airflow guide, Removing the airflow guide

Models: FL939UT FL939UT#ABA Z800 Sp632up SP632UPABA

1 248

Download 248 pages 41.19 Kb

Page 88

Airflow guide

This section describes how to remove and install the chassis airflow guide.

Removing the airflow guide

1.Disconnect power from the workstation (see Predisassembly procedures on page 73).

2.Remove the side access panel (see Removing the side access panel on page 75).

3.Remove the airflow guide by lifting firmly on the handle at the green touch point , and then rotating the airflow guide upward 2 as shown in the following figure.

Figure 5-4Releasing the airflow guide

4.Disengage the airflow guide tabs from the rear chassis slots , and then lift the airflow guide from the chassis 2 as shown in the following figure.

Figure 5-5Removing the airflow guide

76 Chapter 5 Replacing components

ENWW

Image 88

HP Z800 Sp632up SP632UPABA, FL939UT FL939UT#ABA manual Airflow guide, Removing the airflow guide

Contents

HP 800 Workstation Copyright Information Warranty Trademark CreditsAbout this guide Guide topicsIv About this guide Table of contents Restoring the operating system System managementReplacing components Customer self-repair Removing and installing components Removing an optical disk drive from the optical drive bay Diagnostics and troubleshooting CPUConfiguring password security and resetting Cmos Configuring RAID devicesAppendix a Connector pins Appendix D Locating HP resources Appendix B System board designators Appendix C Routine Care235 System board architecture DescriptionTopics Addition features Processor technologyMemory technology GraphicsWorkstation components 1Workstation component descriptions Chassis componentsDescription Front panel components Item Symbol Description2Front panel components Rear panel components 3Rear panel componentsSpecifications Physical characteristicsWeight Chassis DimensionsEnvironmental specifications 4HP Workstation environmental specificationsTemperature Humidity Altitude Shock Vibration Non-operatingPower supply description Power supply voltages5Power supply source voltages Source voltage Description6Maximum current per rail Power supply currentsVoltage rail Power supply specifications Power consumption and heat dissipation7Power supply specifications 100-240 VAC 118 VACResetting the power supply System fansFeatures Ensuring proper ventilationTopics Energy Star Qualification EUP compliance mode AccessibilityEnabling EUP compliance mode Disabling EUP compliance modeIntel Turbo Boost Technology Hyper-threadingHP Cool Tools Setting up the operating system Installing or upgrading device drivers Setting up the Microsoft operating systemTransferring files and settings to your Windows workstation Setting up Red Hat Enterprise Linux Installing with the HP driver CDSetting up Novell Sled Installing and customizing Red Hat-enabled workstationsUpdating the workstation after first boot Upgrading the BiosDetermining current Bios Upgrading Bios Upgrading device driversRestore methods Restoring the operating systemOrdering the RestorePlus! media Ordering backup software Restoring Windows VistaRestoring the operating system Creating RestorePlus! media Restoring Windows XP ProfessionalCreating HP Backup and Recovery Hpbr media Creating restore media Using RestorePlusUsing Hpbr Using the recovery partitionRestoring Novell Sled System management Computer Setup F10 Utility Computer Setup F10 functionalityEnww Accessing the Computer Setup F10 Utility 1Computer Setup F10 Utility menu descriptions Computer Setup F10 Utility menuHeading Option Description Disable 16 is the default As a bootable device Enabled by the operating system MWAITE-AWARE OS PCI VGA HP Z800 Workstation PCI slots HP Z600 PCI slotsHP Z400 Workstation PCI slots Workstation management Section topicsInitial workstation configuration and deployment Installing a remote systemReplicating the setup Copying a setup configuration to a single workstationCopying a setup configuration to multiple workstations Updating and managing software Altiris Client Management SolutionsHP Client Manager Software Proactive Change Notification System Software ManagerSubscribers Choice Remote ROM Flash ROM FlashHPQFlash F10 Flash FailSafe Boot Block ROM Recovering the workstation from Boot Block Recovery modeWorkstation security Asset trackingFeature Purpose How it is established 2Security features overviewSata hard disk drive security Using DriveLock DriveLock applicationsEnabling DriveLock Select SecurityDriveLock SecurityPassword security Establishing a power-on password using workstation setup Entering a power-on passwordEntering a setup password Changing a power-on or setup passwordDeleting a power-on or setup password National keyboard delimiter characters3National keyboard delimiter characters Language DelimiterClearing passwords Side access panel key lockSide access panel sensor Smart Cover Sensor optional 4Side access panel sensor protection levelsSetting the Side access panel sensor protection level Cable lock optionalFault notification and recovery ECC fault predictionDrive Protection System Thermal sensorsDual-state power button Changing the power button configurationReplacing components Enww ESD information Service considerationsGenerating static Preventing ESD equipment damage Personal grounding methods and equipment1Static shielding protection levels Method VoltageGrounding the work area Recommended ESD prevention materials and equipmentTools and software requirements Cables and connectorsSpecial handling of components Customer self-repair Lithium coin cell batteryHard drives Removing and installing components 2System board components ID Component locationsComponent Enww Disassembly order 3Workstation component disassembly orderPredisassembly procedures Cable lock optional 2Removing the cable lock Replacing componentsRemoving the side access panel Side access panelInstalling the side access panel Airflow guide Removing the airflow guideExpansion card support Installing the airflow guideRemoving the expansion card support 8Removing the expansion card support Replacing components Installing the expansion card support 9Installing the expansion card supportPower supply Installing the right side panelRemoving the power supply Right side panelSpeaker Installing the power supplyRemoving the speaker Installing the speaker Side access panel sensor optionalRemoving the side access panel sensor Installing the side access panel sensor Power connections 4Workstation power connector descriptionFront bezel Installing the front bezelRemoving the front bezel Front panel I/O cable assembly Removing the front panel I/O cable assemblyEnww Installing the front panel I/O cable assembly 5Connecting the front panel I/O cable assembly cablesEnww Power switch cable assembly Removing the power switch cable assemblyOptical bay filler tray Installing the power switch cable assemblyRemoving a filler tray 22Removing a filler tray Replacing components Installing a filler tray 23Installing a filler trayOptical disk drive Removing an optical disk drive from the optical drive bayEnww Installing an optical disk drive in the optical drive bay Enww Blu-ray movie playback compatibility and update Blu-ray movie playbackSlot load optical disk drive optional Removing the slot load optical disk driveEnww 33Removing the optical disk drive from the carrier Installing the slot load optical disk drive Enww Enww Hard disk drive TopicRemoving a hard disk drive from the hard drive bay Installing a hard disk drive in the hard drive bay Hard disk drive cable configurationInstalling a hard disk drive Enww Enww Removing a hard disk drive from the slot load optical bay Enww 50Removing the drive screws Enww Installing a hard disk drive in the slot load optical bay 53Fasten the hard drive in the carrierEnww Enww Enww Removing a hard disk drive from the optical drive bay 60Removing the drive from the ODD bayEnww Installing a hard disk drive in the optical drive bay Enww Installing dual SFF hard drives in the optical drive bay Installing the hard drivesEnww Configuring the cabling Expansion card guide/front fan holder Removing the expansion card guide/front fan holder73Disconnecting the fan cable Enww Installing the expansion card guide/front fan holder Removing the rear system fan assembly System fansInstalling the rear system fan assembly 76Removing the rear system fansInstalling a second front system fan Enww Enww Enww Memory fans Removing the memory fansInstalling the memory fans Dimm installation guidelines Supported Dimm configurations MemoryBios errors and warnings Removing a Dimm Installing a Dimm Required Dimm installation orderSingle processor configuration Dual processor configurationInstalling the Dimm Enww Expansion card slot identification Expansion card slot description6Expansion card slot description and compatibility Slot Type Mechanical Electrical75W 150W 175W Power supply Graphics card maximum75W 150W 175W 225W Choosing an expansion card slot PCIe card Removing a PCIe cardInstalling a PCIe card Enww PCI card Removing a PCI cardInstalling a PCI card Enww CPU heatsink Removing the CPU heatsinkEnww Installing the CPU heatsink Enww CPU Removing a CPUInstalling a CPU System board Removing the system boardEnww Installing the system board BatteryRemoving the battery 105Removing the battery Replacing components Installing the battery Product recyclingDiagnostics and troubleshooting Calling technical support Locating ID labelsLocating warranty information Diagnosis guidelines Diagnosis at startupTroubleshooting checklist Diagnosis during operationTroubleshooting checklist HP troubleshooting resources and tools Troubleshooting a problemHP Help and Support Center SupportProduct Change Notifications Helpful hintsAt startup During operation Customizing the monitor displayTroubleshooting scenarios and solutions Solving minor problems1Minor problems Problem Cause Possible SolutionTesting power supply Solving power supply problemsProblem Cause 2Power supply problems Problem Cause Solution3Diskette problems Solving diskette problemsSelect FilePropertiesTools Solving hard drive problems 4Hard drive problemsBoot in StorageBoot Order F1440SecurityRestore Master Boot Record Solving display problems 5Display problemsSelect StartAll Programs AccessoriesSystem Support.html6Audio problems PropertiesFor this CD-ROM device Devices7Printer problems Solving printer problemsDIR C\ printer port Self-troubleshooting with HP Vision Field Diagnostics OverviewDownloading and accessing HP Vision Field Diagnostics Locate HP Vision Field Diagnostics and select DownloadUser interface Survey tabEnww Test tab Enww Status tab Errors tabHistory tab Help tab Downloading the latest diagnostic utility Diagnostic codes and errorsDiagnostic LED and audible beep codes 8Diagnostic lights and audible codes Activity Possible causeActivity Possible cause Recommended action Supply on page 80 for detailsRed Power LED blinks nine 9LED color definitions LED color definitionsLED state LED color System status 10POST error messages Post error messagesScreen message Probable cause Recommended action Is missing critical SPD information, or If necessary, add a heatsink to the processor Screen message Probable cause Replace the processor with a compatible one Enww Maximum hard drive configurations 1Maximum hard drivesConfiguring Sata RAID devices Attaching Sata HDDsConfiguring system Bios Creating RAID volumes Deleting RAID volumes Configuring SAS RAID devices Supported configurationsSAS RAID 0 configuration SAS RAID 1 configuration SAS RAID 1E configuration Configuring password security and resetting Cmos Preparing to configure passwordsClearing and Resetting the Cmos Resetting the password jumperUsing the Cmos Button Using the Computer Setup F10 Utility to Reset Cmos Enww Workstation PS/2 mouse Pin Signal Workstation PS/2 keyboard Pin SignalWorkstation Ethernet Pin 10/100-MbSignal Workstation serial Pin Signal Workstation USB Pin SignalWorkstation IEEE-1394a Pin Signal Pin SignalSata drive Pin Signal Data Cable Power Cable 217SAS drive Segment Pin PlugCable ReceptaclesWorkstation VGA Pin Signal DVI-I cable Pin SignalMain power cable, P1 Display portCPU power cable, P3 Pin Signal Color Memory power cable, P2 Pin Color SignalHDD bay power cable Pin Color Signal Graphics aux. power cables, P10, P11 Signal P11 Signal P10 Color Pin850W 1110W V12-G V12-G1 V12-G2Workstation CPU fans, P70, P71 Pin Signal Workstation front system fan 1, P93 Pin SignalWorkstation front system fan 2, P94 Pin Signal Workstation rear system fans, P8 Pin SignalWorkstation FDD Pin Signal System board designators Designator Silk screen ComponentAppendix B System board designators Cleaning the workstation case General cleaning safety precautionsCleaning the keyboard Cleaning the monitor Cleaning the mouseLocating HP resources Product information Table D-1Product informationTopic Location All Programs HP Cool ToolsProduct support Table D-2Product supportTable D-3Product documentation Product documentationCustomer Bulletins, or Customer Notices Product diagnostics Table D-4Product diagnosticsProduct updates Table D-5Product updatesTaskUse Tools to view...ToolsMy Computer InformationView general system informationIndex AppendicesEnww