Slot load optical disk drive optional | HP FL939UT FL939UT#ABA

Slot load optical disk drive (optional)

A slot load optical disk drive can be added to the workstation in place of the standard optical disk drive assemblies. The slot load optical bay fits into the chassis and replaces all the standard optical bays.

This section describes how to remove and install a slot load optical disk drive.

Removing the slot load optical disk drive

1.Disconnect power from the workstation (see Predisassembly procedures on page 73).

2.Remove the side access panel (see Removing the side access panel on page 75).

3.Remove the expansion card support and any card cables that might interfere with slot load assembly removal.

4.Remove the airflow guide (see Removing the airflow guide on page 76).

5.Disconnect the slot load optical disk drive data cable from the system board connector as shown in the following figure.

Figure 5-29Disconnecting the data cable from the system board

6.Disconnect the chassis power cable from the slot load optical drive power connector as shown in the following figure.

Figure 5-30Disconnecting chassis power cable from optical disk drive power cable

ENWW	Removing and installing components 99

Image 111

HP FL939UT FL939UT#ABA manual Slot load optical disk drive optional, Removing the slot load optical disk drive

Contents

HP 800 Workstation Trademark Credits Copyright Information Warranty Guide topics About this guide Iv About this guide Table of contents System management Restoring the operating system Replacing components Customer self-repair Removing and installing components Removing an optical disk drive from the optical drive bay CPU Diagnostics and troubleshooting Configuring RAID devices Configuring password security and resetting CmosAppendix a Connector pins Appendix B System board designators Appendix C Routine Care Appendix D Locating HP resources235 Description System board architectureTopics Graphics Addition featuresProcessor technology Memory technology Workstation components Chassis components 1Workstation component descriptionsDescription Item Symbol Description Front panel components2Front panel components 3Rear panel components Rear panel components Chassis Dimensions SpecificationsPhysical characteristics Weight Non-operating Environmental specifications4HP Workstation environmental specifications Temperature Humidity Altitude Shock Vibration Source voltage Description Power supply descriptionPower supply voltages 5Power supply source voltages Power supply currents 6Maximum current per railVoltage rail 100-240 VAC 118 VAC Power supply specificationsPower consumption and heat dissipation 7Power supply specifications System fans Resetting the power supply Ensuring proper ventilation Features Topics Energy Star Qualification Disabling EUP compliance mode EUP compliance modeAccessibility Enabling EUP compliance mode Hyper-threading Intel Turbo Boost TechnologyHP Cool Tools Setting up the operating system Setting up the Microsoft operating system Installing or upgrading device driversTransferring files and settings to your Windows workstation Installing with the HP driver CD Setting up Red Hat Enterprise Linux Upgrading the Bios Setting up Novell SledInstalling and customizing Red Hat-enabled workstations Updating the workstation after first boot Determining current Bios Upgrading device drivers Upgrading Bios Restoring the operating system Restore methods Ordering backup software Restoring Windows Vista Ordering the RestorePlus! mediaRestoring the operating system Restoring Windows XP Professional Creating RestorePlus! media Creating HP Backup and Recovery Hpbr media Using the recovery partition Creating restore mediaUsing RestorePlus Using Hpbr Restoring Novell Sled System management Computer Setup F10 functionality Computer Setup F10 Utility Enww Accessing the Computer Setup F10 Utility Computer Setup F10 Utility menu 1Computer Setup F10 Utility menu descriptionsHeading Option Description Disable 16 is the default As a bootable device Enabled by the operating system MWAITE-AWARE OS PCI VGA HP Z600 PCI slots HP Z800 Workstation PCI slots HP Z400 Workstation PCI slots Section topics Workstation management Installing a remote system Initial workstation configuration and deployment Copying a setup configuration to a single workstation Replicating the setup Copying a setup configuration to multiple workstations Altiris Client Management Solutions Updating and managing softwareHP Client Manager Software System Software Manager Proactive Change NotificationSubscribers Choice ROM Flash Remote ROM FlashHPQFlash F10 Flash Recovering the workstation from Boot Block Recovery mode FailSafe Boot Block ROM Asset tracking Workstation security 2Security features overview Feature Purpose How it is establishedSata hard disk drive security DriveLock applications Using DriveLock Select SecurityDriveLock Security Enabling DriveLock Password security Entering a power-on password Establishing a power-on password using workstation setup Changing a power-on or setup password Entering a setup password Language Delimiter Deleting a power-on or setup passwordNational keyboard delimiter characters 3National keyboard delimiter characters 4Side access panel sensor protection levels Clearing passwordsSide access panel key lock Side access panel sensor Smart Cover Sensor optional Cable lock optional Setting the Side access panel sensor protection level Thermal sensors Fault notification and recoveryECC fault prediction Drive Protection System Changing the power button configuration Dual-state power button Replacing components Enww Service considerations ESD informationGenerating static Method Voltage Preventing ESD equipment damagePersonal grounding methods and equipment 1Static shielding protection levels Recommended ESD prevention materials and equipment Grounding the work area Cables and connectors Tools and software requirementsSpecial handling of components Lithium coin cell battery Customer self-repairHard drives Removing and installing components Component locations 2System board components IDComponent Enww 3Workstation component disassembly order Disassembly order Predisassembly procedures 2Removing the cable lock Replacing components Cable lock optional Side access panel Removing the side access panelInstalling the side access panel Removing the airflow guide Airflow guide Installing the airflow guide Expansion card supportRemoving the expansion card support 8Removing the expansion card support Replacing components 9Installing the expansion card support Installing the expansion card support Right side panel Power supplyInstalling the right side panel Removing the power supply Installing the power supply SpeakerRemoving the speaker Side access panel sensor optional Installing the speakerRemoving the side access panel sensor Installing the side access panel sensor 4Workstation power connector description Power connections Installing the front bezel Front bezelRemoving the front bezel Removing the front panel I/O cable assembly Front panel I/O cable assembly Enww 5Connecting the front panel I/O cable assembly cables Installing the front panel I/O cable assembly Enww Removing the power switch cable assembly Power switch cable assembly Installing the power switch cable assembly Optical bay filler trayRemoving a filler tray 22Removing a filler tray Replacing components 23Installing a filler tray Installing a filler tray Removing an optical disk drive from the optical drive bay Optical disk drive Enww Installing an optical disk drive in the optical drive bay Enww Blu-ray movie playback Blu-ray movie playback compatibility and update Removing the slot load optical disk drive Slot load optical disk drive optional Enww 33Removing the optical disk drive from the carrier Installing the slot load optical disk drive Enww Enww Topic Hard disk drive Removing a hard disk drive from the hard drive bay Hard disk drive cable configuration Installing a hard disk drive in the hard drive bay Installing a hard disk drive Enww Enww Removing a hard disk drive from the slot load optical bay Enww 50Removing the drive screws Enww 53Fasten the hard drive in the carrier Installing a hard disk drive in the slot load optical bay Enww Enww Enww 60Removing the drive from the ODD bay Removing a hard disk drive from the optical drive bay Enww Installing a hard disk drive in the optical drive bay Enww Installing the hard drives Installing dual SFF hard drives in the optical drive bay Enww Configuring the cabling Removing the expansion card guide/front fan holder Expansion card guide/front fan holder 73Disconnecting the fan cable Enww Installing the expansion card guide/front fan holder System fans Removing the rear system fan assembly 76Removing the rear system fans Installing the rear system fan assembly Installing a second front system fan Enww Enww Enww Removing the memory fans Memory fans Installing the memory fans Memory Dimm installation guidelines Supported Dimm configurations Bios errors and warnings Removing a Dimm Dual processor configuration Installing a DimmRequired Dimm installation order Single processor configuration Installing the Dimm Enww Slot Type Mechanical Electrical Expansion card slot identificationExpansion card slot description 6Expansion card slot description and compatibility Power supply Graphics card maximum 75W 150W 175W75W 150W 175W 225W Choosing an expansion card slot Removing a PCIe card PCIe card Installing a PCIe card Enww Removing a PCI card PCI card Installing a PCI card Enww Removing the CPU heatsink CPU heatsink Enww Installing the CPU heatsink Enww Removing a CPU CPU Installing a CPU Removing the system board System board Enww Battery Installing the system boardRemoving the battery 105Removing the battery Replacing components Product recycling Installing the battery Diagnostics and troubleshooting Locating ID labels Calling technical support Locating warranty information Diagnosis at startup Diagnosis guidelines Diagnosis during operation Troubleshooting checklist Troubleshooting checklist Support HP troubleshooting resources and toolsTroubleshooting a problem HP Help and Support Center Helpful hints Product Change NotificationsAt startup Customizing the monitor display During operation Problem Cause Possible Solution Troubleshooting scenarios and solutionsSolving minor problems 1Minor problems Solving power supply problems Testing power supplyProblem Cause Problem Cause Solution 2Power supply problems Solving diskette problems 3Diskette problemsSelect FilePropertiesTools F1440 Solving hard drive problems4Hard drive problems Boot in StorageBoot Order SecurityRestore Master Boot Record 5Display problems Solving display problems Support.html Select StartAll Programs AccessoriesSystem Devices 6Audio problemsProperties For this CD-ROM device Solving printer problems 7Printer problemsDIR C\ printer port Overview Self-troubleshooting with HP Vision Field Diagnostics Locate HP Vision Field Diagnostics and select Download Downloading and accessing HP Vision Field Diagnostics Survey tab User interface Enww Test tab Enww Errors tab Status tabHistory tab Help tab Diagnostic codes and errors Downloading the latest diagnostic utilityDiagnostic LED and audible beep codes Activity Possible cause 8Diagnostic lights and audible codes Supply on page 80 for details Activity Possible cause Recommended action Red Power LED blinks nine LED color definitions 9LED color definitionsLED state LED color System status Post error messages 10POST error messagesScreen message Probable cause Recommended action Is missing critical SPD information, or If necessary, add a heatsink to the processor Screen message Probable cause Replace the processor with a compatible one Enww 1Maximum hard drives Maximum hard drive configurations Attaching Sata HDDs Configuring Sata RAID devices Configuring system Bios Creating RAID volumes Deleting RAID volumes Supported configurations Configuring SAS RAID devices SAS RAID 0 configuration SAS RAID 1 configuration SAS RAID 1E configuration Preparing to configure passwords Configuring password security and resetting Cmos Resetting the password jumper Clearing and Resetting the CmosUsing the Cmos Button Using the Computer Setup F10 Utility to Reset Cmos Enww Workstation PS/2 keyboard Pin Signal Workstation PS/2 mouse Pin SignalWorkstation Ethernet Pin 10/100-MbSignal Pin Signal Workstation serial Pin SignalWorkstation USB Pin Signal Workstation IEEE-1394a Pin Signal 217 Sata drive Pin Signal Data Cable Power Cable Receptacles SAS drive Segment PinPlug Cable DVI-I cable Pin Signal Workstation VGA Pin Signal Display port Main power cable, P1 Memory power cable, P2 Pin Color Signal CPU power cable, P3 Pin Signal ColorHDD bay power cable Pin Color Signal V12-G V12-G1 V12-G2 Graphics aux. power cables, P10, P11Signal P11 Signal P10 Color Pin 850W 1110W Workstation rear system fans, P8 Pin Signal Workstation CPU fans, P70, P71 Pin SignalWorkstation front system fan 1, P93 Pin Signal Workstation front system fan 2, P94 Pin Signal Workstation FDD Pin Signal Designator Silk screen Component System board designators Appendix B System board designators General cleaning safety precautions Cleaning the workstation caseCleaning the keyboard Cleaning the mouse Cleaning the monitor Locating HP resources All Programs HP Cool Tools Product informationTable D-1Product information Topic Location Table D-2Product support Product support Product documentation Table D-3Product documentationCustomer Bulletins, or Customer Notices Table D-4Product diagnostics Product diagnostics InformationView general system information Product updatesTable D-5Product updates TaskUse Tools to view...ToolsMy Computer Appendices Index Enww