Juniper Networks E-Series - page 167

I/O Module Specifications

E-Series Routers

12-23

GE

I/O

SFPb,d

ASIC ERX-7xx models

ERX-14xx models

ERX-310 router

SRP-5G+

SRP-10G

SRP-40G

SRP-40G+

SRP-SE10G

1 active

1 redundant

LC full duplex •Tx power:

›min: –9.5 dBm

›max: –3 dBm

• Center wavelength: 1300 nm

• Rx input power:

›min: –20 dBm

›max: –3 dBm

• Rated for 10 km (6.2 miles) over

10-micron core cable

GE

I/O

SFPb,e

ASIC ERX-7xx models

ERX-14xx models

ERX-310 router

SRP-5G+

SRP-10G

SRP-40G

SRP-40G+

SRP-SE10G

1 active

1 redundant

LC full duplex •Tx power:

›min: –3 dBm

›max: 2 dBm

• Center wavelength: 1550 nm

• Rx input power:

›min: –23 dBm

›max: –3 dBm

• Rated for 70 km (43.4 miles) over

10-micron core cable

GE

I/O

MULTI

MODEc

ASIC ERX-7xx models

ERX-14xx models

ERX-310 router

SRP-5G+

SRP-10G

SRP-40G

SRP-40G+

SRP-SE10G

1 active

1 redundant

SC full duplex •Tx power:

›min: –9.5 dBm

›max: –4 dBm

• Center wavelength: 850 nm

• Rx input power:

›min: –17 dBm

›max: –3 dBm

• Rated for 275 m (300 yards) over

62.5-micron core cable

• Rated for 550 m (601 yards) over

50-micron core cable

Table12-3 I/O module specifications (continued)

I/O Module LabelaType

Model

Compatibility

SRP Module

Compatibility

No. of

Ports Connector Type Cabling Specifications

Contents

Main Federal Communications Commission (FCC) Statement FCC Requirements For Consumer Products Food and Drug Administration, Center for Devices and Radiological Health Canadian Department Of Communications Radio Interference Regulations Rglement sur le brouillage radiolectrique du ministre des communications Industry Canada Notice CS-03 Avis CS-03 dIndustrie Canada D.O.C. Explanatory Notes: Equipment Attachment Limitations Notes explicatives du ministre des Communications: limites visant les accessoires EC Declaration of Conformity Voluntary Control Council for Interference (VCCI) Statement for Japan SOFTWARE LICENSE AGREEMENT Page Page Page Contents Part 1. Installing and Using E-Series Routers Page Page Page Part 2. System and Module Specifications Part 3. Appendixes Page About This Guide E-Series Routers Audience Conventions Documentation Page Comments About the Documentation Page Page Page E-Series Overview Where E-Series Routers Fit In E-Series Routers Page Page Page Page Page Page E-Series Modules Page Page Page Page Network Management Tools Redundancy Features Page Page Page Page Unpacking and Inspecting E-Series Before You Begin Unpacking ERX-14xx Models Unpacking ERX-7xx Models and ERX-310 Routers Inspecting E-Series Router Components and Accessories If You Detect or Suspect Damage Contacting Juniper Networks Page Installation Guidelines and Requirements Your Preinstallation Responsibilities Environmental Requirements Regulatory Compliances Safety Guidelines For you r safe ty, befo re ins tall ing th e system, review all safety warnings in this section. Equipment Rack Requirements Page Page Page Cabling Recommendations Installing E-Series Before You Begin Freestanding Installation Rack-Mounted Installation Page Page Page Installing Modules Page Page Page Page Page Safety Guidelines Before and during the installation process, observe the following precautions: Installing SRP I/O and SRP Modules Page Page Installing Line and I/O Modules Removing a Module Page Installing Components for Line Module Redundancy Page Page Configuring Line Module Redundancy Cabling E-Series Cabling Overview Page Page Required Tools, Wires, and Cables Cabling the SRP I/O Module CHAPTER 6 Cabling E-Series Routers 6-6 g013750 CONSOLE Note: Use shielded cables to connect the external clock sources to the clock source input ports. RJ-45 DB-9 Figure 6-2 ERX-14xx model SRP I/O module ALARMSEXTERNAL TIMING Page Page Cabling the E-Series Router for Power 1Switch all E-series router power switches to OFF. Caution: Switches may have inadvertently flipped to ON during shipping and installation. 2Connect the grounding wires to the chassis. 3Connect the power cables (AC or DC) to the power input modules. ! Power input module cover Page Page Page Cabling I/O Modules HSSI Connectors The HSSI I/O module uses a standard 50-pin HSSI connector. RJ-45 Connectors When inserting an RJ-45 connector, be sure it clicks into the port. RJ-48C Connectors When inserting an RJ-48C connector, be sure it clicks into the port. Port 0 Page Page Page Page Powering Up E-Series Before You Power Up the System Powering Up Status LEDs Powering Down Page Accessing E-Series Setting Up Management Access Console Port Setup Page Teln et Setu p Page SNMP Maintaining E-Series Required Tools and Items Storing Modules and Components Cleaning the System Upgrading NVS Cards on SRP Modules Page Page Upgrading Memory on SRP Modules Page Page Replacing SFPs on GE I/O Modules Page Page Page Replacing Fan Trays Page Page Installing a Cable-Management Bracket on ERX-7xx Models Troubleshooting Diagnosing Problems Troubleshooting Power Failures Understanding Status LEDs to Troubleshoot Page Page Ethernet line module (Figure 10-2) Other line modules (Figure 10-3) Page Page Page Monitoring Temperatures of Modules Resetting Line Modules and SRP Modules Double-Bit Errors on SRP Modules Page Page Page Page System Specifications ERX-14xx Models Specifications Page ERX-7xx Models Specifications Page ERX-310 Router Specifications Page Page Page Module Specifications Module Functionality Page Page Page Page Page Page Page Page Page Page Page Module Specifications Page Page I/O Module Specifications compatibility, SRP module compatibility, number of ports, connector type, and cabling See Tabl e 12-3 on the following pages for I/O module details such as module type, E-series model specifications. Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Protocol Support Channelized OCx/STMx Modules Channelized T1 and E1 Modules Channelized T3 Modules Page Ethernet Modules HSSI Modules Page OCx/STMx ATM Modules OCx/STMx POS and OC48 Modules Page Tunnel Service Modules Unchannelized E3 Modules Page Unchannelized T3 Modules Page X.21/V.35 Modules Page Page Page A Cable Pinouts SRP I/O Module Page Page CT1 and CE1 I/O Modules Page Page Page Page B Installing JUNOSe Software Installing Software When a Firewall Exists Page Page Page Page Page Installing Software When a Firewall Does Not Exist Page Page Page Page Page Page Copying Release Files from One E-Series Router to Another Upgrading Systems That Are Operating with Two SRP Modules Page Page C Customer Support Contact Information Page Returning Products for Repair or Replacement Page D Declaration of Conformity Page Index Numbers A B C D E F H I L M N O P Q R S T