Manuals / Ricoh / Computer Equipment / Printer

Ricoh AP305 operating instructions Remove the misfed paper from inside of the printer

Models: AP305

1 156

Download 156 pages 32.85 Kb

Page 109

Removing Misfed Paper

B Open the front cover by pushing the front cover release button.

TFWX080E

C Turn the dial downward, then re- move the misfed paper in the printer.

Note

❒When removing misfed paper, be careful not to touch the fus- ing section because it could be very hot.

When you can see the misfed paper inside the printer.

Note

❒If it is difficult to turn the dial, turn it slightly upward in the opposite direction, and then try again.

A Remove the misfed paper from inside of the printer.

While turning the dial, remove the misfed paper as shown in the illustration. Be careful not to leave any misfed paper in the printer.

Note

❒When removing misfed pa- per, be careful not to touch

the fusing section because it could be very hot.

TFWX220E

When you cannot see the misfed paper inside the printer.

A Remove the misfed paper from the output tray.

While turning the dial, remove the misfed paper as shown in

the illustration. Be careful not to 6 leave any misfed paper in the printer.

Note

❒When removing misfed pa- per, be careful not to touch the fusing section because it could be very hot.

TEWX240E

D Close the paper exit cover.

E Close the front cover.

79

Image 109

Ricoh AP305 Remove the misfed paper from inside of the printer, Remove the misfed paper from the output tray

Contents

Operating Instructions Overseas Affiliates Page Means Power on Means Power OFF Page Means Power on Means Power OFF Page Means Power on Means Power OFF Trademarks Safety During Operation Safety InformationIii Page Specifications Low-power mode Energy Saver modeEnergy Star Program Color Printing Basics Color GuideAdditive Emitted and Subtractive Reflected Color Models Vii Printed Color Resolution Example of Color Adjustments Using the Printer Driver600 dpi 300 dpi Auto Edge SmoothingOff LimitationToner Saving Standard Image PrintingFast FineColor Correction Color Adjustments Using the Printer DriverOff Vivid ReferenceColor Level PhotographicBit Contrast BrightnessSaturation Color Balance Manuals for Your Printer Quick Installation GuideManuals for Your Printer Operating Instructions this manualSymbols How to Read this ManualPreparation Table of Contents Cleaning and Adjusting the Printer Error & Status MessagesSetting Menus Protecting the Menus Menu SettingsMoving and Transporting the Printer 115 Specifications 116 Printing the Color Sample 110 Resetting Menus 111Memory Capacity and Paper Size 113 Consumables 120 Glossaries 122Xxii Exterior-Front View Guide to the PrinterPaper Tray Bypass trayExterior-Rear View Interior Operation Panel Data In indicator Error indicatorTurning On the Printer Turning the Printer On and OffWarming Up ReadyGetting Acquainted Installing Options Interface Board Available OptionsMemory Unit ⇒ P.11 RICOH-SCRIPT2 Type305 ⇒ P.13 Paper Feed Unit Type305 ⇒ P.19⇒ P.107 Printing the Configura- tion Installing the Memory Unit SimmInstalling Options Check the contents of the box for the following items Installing the RICOH-SCRIPT2 Type305Reference Installing Network Interface Board Type305 Reference Installing the Ieee 1284 Parallel Type305 Installing Options Move the printer to make install- ing space Installing the Paper Feed Unit Type305Pull out the paper tray, and re- move the padding Remove both pieces of adhesive tapeRemove the ring attached to the red tag Place the printer on the paper feed unitInstalling the Paper Feed Unit Type305 Installing Options Press Menu Press UT until the following message appears Menu System MenuActive PTL All Active System Menu j 39.Active PTL. lSystem Menu j 32.IP Address l 011.022.033.044 Jjl/#Net Boot None System Menu Net Boot191.168.015.016 j System Menu Frame NW Access Control Address and Access Control MaskFrame NW Auto Select Subnet MaskThese settings control only printing requests Page Before Installing the Printer Driver Installing the IPDL-C Printer DriverInstalling the Printer Drivers Printer Driver Installation Windows 95/98 Installing the IPDL-C Printer DriverPlug and Play When the New Hardware Found dialog appears Installing the Printer Driver Using Plug and PlayWhen the Device Driver Wizard appears When Windows 95/98 starts normallyClick OK Restart Windows after completing the installationClick Finish Add Printer Wizard appears Installing the Printer Driver Without Using Plug and PlayClick Have Disk Click BrowseSetting Up Options On the Document menu, click Cancel Printing Canceling a Print JobDouble-click the printer icon on the Windows Task Bar Installing the Printer Driver Windows 3.1x Installing the IPDL-C Printer DriverClick Browse… Tions dialog from an application Setting Up OptionsOn the Document menu, click Delete Document Click Have Disk… Windows NT4.0 Installing the IPDL-C Printer DriverClick the Installable Options tab Click OK to close the printer properties Paper Types and Sizes Paper and Other Media Supported by this PrinterPaper Sizes ⇒ P.52 Loading Paper in the Bypass Tray Paper types and cautions Plain paper Precautions for PaperAdhesive labels Thick PaperPaper not supported by this printer OHP transparenciesPrintable Area Loading Paper in the Paper Tray Loading PaperLoad paper into the tray with the print side up Paper Size Standard Optional Tray Tray1 Tray2/3 Slide the paper tray completely into the printerTray Size* j 5x13 l Menu IPDL-C MenuTray Size* j 25x13 l Ready5Open the bypass tray Loading Paper in the Bypass TraySlide the side guides Load paper until it stops with the print side downPaper Tray j Tray1/A4 l Media j 1.Paper Tray lMedia j 2.Paper Size l Custom Jl/# Width 297mmRepeat step B to set the value of the width Sliding out the Output Tray ExtenderRepeat steps B and C to set the value of the length Press EscapePrinted Error Message Error & Status MessagesMessage Description Comments Error & Status Messages on the Operation Panel⇒ P.76 Removing Misfed Paper Menu Setting Up Options Message Description Comments Printer Current Status Getting Printer Information over the NetworkMshell After this message appears Placing the Waste Toner Bottle and Charger Printer Configuration Input Tray Paper Size Input Tray NameInput Tray Status Emulation Name Printer Doesnt Print Possible Cause SolutionsNetwork Connection If the printer is using I/O TimeoutProperties Windows 95/98Windows Click ConnectStatus Possible Causes, Descriptions, and Solutions Other Printing ProblemsIng Paper in the Paper Tray Charger and P.81 Cleaning the Dust-proofing glass Ing the Charger Or Setting tab Other Printing Problems Removing Misfed Paper Standard Tray Tray1 or Paper Feed Unit Tray2/3 When the Message Open Front Cover Remove Misfeed AppearsBypass tray Carefully pull the misfed paperClose the front cover When the Message Remove Misfeed From Output Tray AppearsOpen the paper exit cover Remove the misfed paper from the output tray Remove the misfed paper from inside of the printerClose the paper exit cover Close the front cover Cleaning the Friction Pad Cleaning and Adjusting the PrinterCleaning the Charger Remove the cleaning brush from back of the front cover Cleaning the Dust-proofing glassMenu j Maintenance l Adjusting the Image DensityMaintenance j 1.Toner Selectl Maintenance j 2.Toner Level lList Print Config.Page Adjusting the SettingTray Magenta jl/# ------g-----+Maintenance j 1.Toner Selectl Tray2W jl/# ------g-----+ Menu MaintenanceMaintenance j 4.Registrationl Menu List PrintAdd Toner Replacing ConsumablesOpen the left cover Slide the lock lever upSlide the new toner cartridge into the printer Remove the protective sheet from the new toner cartridgeReturn the lock lever to its origi- nal position Pull the tape out as shown in the illustrationToner Select Please Wait Toner Select j BlacklToner Select Add Toner Specifying the replacing toner cartridgeReplacing the Photoconductor Unit Turn off the printers power switchChange PCU TFWX400E Replacing the Fuser Oil Bottle and Ozone Filter Turn on the printer’s power switchAdd FuserOil Close the fuser oil bottle cover Remove the green cap from the new oil bottleInsert a new ozone filter into the printer Waste T Full Waste Toner isTFWX330E Push the right and left lock le- vers of the charger Replace the chargerMenu and Media setting priorities Setting MenusTray Size* j DLl Setting MenusFollowing message appears on the panel display Tray Size* j LTl Take Offline Then Press ResetPress On Line to enter the off-line condition Protecting the Menus Use UT to display Maintenance, and then press EnterProtecting the Menus Maintenance j 5.Menu Protectl Changing the Menu Settings without Removing ProtectMenu Protect j Offl Menu Protect j OnlRemoving Protect Use UT to display Off, and then press Enter Menu Table IPDL-C Menu Menu SettingsSystem Menu ×13 O BufferTransfer Energy LevelImage Memory ParallelOHP Slip Bi-directionPrinterLang LanguageList Print j Config.Page l Printing the ConfigurationConfig.Page Press # key Confirm that Config.Page is on the display, press EnterReference Interpreting ConfigurationPrinter Information Status List Error LogList Print j Color Sample l Printing the Color SampleColor Sample Press # key Use UT to display Color Sample, and then press EnterMaintenance j 5.Menu Reset l Resetting MenusMenu Reset Press # key Turn on the printer’s power switch Press Menu112 Resolution 600 dpi Resolution 300 dpiMemory Capacity and Paper Size Low Memory Moving and Transporting the Printer Mainframe SpecificationsDimensions Noise Emission Sound Power LevelWeight Warm-up TimeOptions Number of Pins Ieee 1284 Parallel Type305 ModeAccess Time Toner Cartridge ConsumablesOther Consumables Service Life *1Glossaries Printer Properties Print PortProportional Fonts RPS2 Edge SmoothingIndex 125 126