Table of pre-alarm recording times, FPS field/sec | Sanyo DSR-3709

2SPECIFICATIONS

Table of pre-alarm recording times

This table indicates recording times for pre-alarm recording, and it should be used when this type of recording is being carried out.

Recording rate

Recording time (Display of time on menu screens s: seconds

m: minutes)

3s

5s

10s

20s

40s

60s

120s

180s

240s

300s

500s

900s

FPS (field/sec)

(3s)

(5s)

(10s)

(20s)

(40s)

(1m)

(2m)

(3m)

(4m)

(5m)

(10m)

(15m)

30.00
20.00
15.00
10.00
7.50
6.00
5.00
4.29
3.75
3.33
3.00
2.73
2.31
2.00
1.67
1.43
1.25
1.11	OTHER
1.00
Default setting, Recording rate: 15 FPS, Recording time: 1 min.

When setting alarm durations using a menu, settings will be restricted to those available for the selected recording rate. Similarly, when setting recording rates, the setting range will be restricted to that available for the selected duration. For example, if the alarm duration is set to 3 seconds, only 30 FPS will be selectable for the recording rate.

When setting fast recording rates, it may be necessary to first of all change the alarm duration setting.

118

English

Image 119

Sanyo DSR-3709, DSR-3716 instruction manual Table of pre-alarm recording times, Minutes 10s 20s 40s, FPS field/sec

Contents

Page Service Precaution Introduction Main featuresAccessories Symbols used in this manual Contents Other Contents Settings „ Handling a detached HDD unit Before USE„ Notes on replacing the HDD Important recordings Backup batteryBefore USE Hard disk and cooling fan are consumable components Front panel Names and Functions of PartsDSR-3716 DSR-3709 Names and Functions of Parts Jog dial inside and shuttle dial outside z During playback Timer button and indicator JP.23Alarm buttons JP.31 Menu Reset button JP.48 Rear panel Pin locations Installation and ConnectionsConnecting RS-485 terminals Basic connections Cable types Installation and ConnectionsRS-485 termination switch settings Connection Amp Sold separately Connecting Sanyo protocol devices Dome CamerasConnecting an amplifier Connecting Alarm in terminals Connecting the power cord Connecting Sensor Alarm OUT terminalsConnecting Control terminals Operation display area 01-01-04 000000 REC Repeat EN a AlarmPreparing for USE Changing the language Preparing for USEChanging the position of the operation display area Example Setting 830 on October 26 Setting the time Normal recording area Alarm recording areaInternal hard disk Hard disk recording areas Press the No Camera Select button Viewing Video from a CameraViewing on a full screen Viewing on quad screens Viewing on plus screen Viewing Video from a CameraViewing on multi screens 9 screens/ 16 screens Press the Sequence button once again Viewing with automatic screen selectionViewing on the monitor Press the Sequence button Selecting Camera No for full screen Set MON.2 Display from Alarm Operation SET to ON. JP.84Displaying alarm video in full screen format Ending the monitor 2 setting procedure Normal recording Timer recordingPress the Timer button Recording When an alarm signal is detected Alarm recordingSet alarm recording End alarm recording Alarm Full indicator Pre-alarm recordingSet pre-alarm recording If an alarm is detected Press the PLAY/STOP button PlaybackPlaying video on a full screen Fast-forward and fast-rewind playback Move the zoom frame to the area to be magnified PlaybackChanging the playback speed Enlarging the playback video Press the Still button once again Viewing still imagesPress the Zoom button Press the Still button during playback Press the Quad button during playback Performing frame advance forward or reversePlaying video on multiple screens Searching from the Search screen Searching for Recorded Video Turn the jog dial to select the video for playback Alarm searchPress the appropriate Alarm button during playback Searching for Recorded Video Time/date search Alarm thumbnail searchTurn the jog dial and select Alarm Thumbnail Search Alarm number for the selected recording will start to flash If no recording exists for the specified time View Selected image is displayed on the preview screen Archive area searchMotion detection search Turn the jog dial to select Archive Area Search END Example AlarmExample Start Set the motion sensor to use for searching „ If not Found is displayed Carry out motion sensor setting againTurn the jog dial to select Preview Copying video to a CD-R/RW JP.45 Saving Copying Recorded VideoCopying video to the hard disk’s archive area JP.39 Copying video to a CompactFlash card or Microdrive JP.41 Example Copying a specified 10-second portion of video Saving Copying Recorded VideoCopying video to the hard disk’s archive area Press the Copy button Turn the jog dial to select Seconds „ To cancel a copy operation Insertion method Removal method Copying video to a CompactFlash card or MicrodriveInsert a CompactFlash card ‹PICTURES When this has been completed, Copy Finished ! is displayed Viewing images copied to a CompactFlash card on a PC Printing images from CompactFlash cards quick print Dcim Turn the jog dial to select the unit Copying video to CD-R/RWConnect a recordable CD-R/RW drive and insert a disk Formatting a CompactFlash card and CD-RW Viewing images copied to a CD-R/RW on a PC Turn the jog dial to select a menu Menu Configuration and OperationsMoving from the Main Menu to a sub-menu or setting screen Basic menu operations Entering numbers with the numeric keys Menu Configuration and OperationsRestoring menu setting items to their default values Movement and confirmation in sub-menus and setting screens Main menu Sub-menu configuration Color Level JP.105 Sub menu Setting item Settings or display contentMulti Screen Sequence SET Initial SET Initial settingsSetting the daylight saving Initial SET is used to make the following setting Initial SET Turn the jog dial to select Mode under Daylight SavingTurn the jog dial to change the settings When USE is selected for Daylight Saving To C Terminal To Clock SET in terminal External clock settingTurn the jog dial and move the cursor to ADJUST. Time Cursor moves to the time Displayed Detecting connected cameras Repeat steps 5 and 6 to enter the remaining characters Setting camera titlesExample Setting the title HALL-1F for Camera No Turn the jog dial to select H Set the month and day for item No Setting holidaysTurn the shuttle dial clockwise after setting Example Setting November 17 as a holiday Setting time periods Time Period a settings Set T-1 to 6 AM Time period settingsExample 1 Setting periods using Time Period a Cursor moves to Mask Time period operations settingsTime Period a flashes Record SET Settings for recordingNormal recording easy setup Camera Select buttons Timer button Jog dial Record SET screen is displayed Setting based on recording daysCursor moves to Timer Recording DLY Record SET Example on Set Picture QualitySet Audio Recording Turn the shuttle dial counter-clockwise Setting based on recording rate Recording Area SET screen is displayed AlarmDisplaying the recording areas „ If the normal recording area is set to 0% „ Default hard disk settingsChanging recording areas „ Recording area allocations Hard disk is initialized Setting overwrite permissionCursor moves to Area Full Reset Turn the shuttle dial counter- clockwise Setting overwriting for the normal recording area Setting recording conditions OFF 01-01-04 000000 REC 1%Display area Capacity Setting series recording Starting and stopping series recording Set depending on your recording needs Turn the shuttle dial clockwise Press the EXIT/OSD button Setting auto deletingSetting normal recording Turn the jog dial to select the storage period Example P-1 Set REC RateSet REC Program Group Cursor moves to 0.5 from Select Individual Camera Rate FPS Setting program recordingCameras No through No are available for the DSR-3709 Selects Program No through Program No Timer setting items Timer settings Start time flashes as „ To change a displayed setting itemTimer SET screen is displayed Cursor moves to the SUN row SUN from the Week column flashes All setting items are cleared Menu Reset button Make settings in the Week and Start columnsTo cancel all set timer reservations Timer reservations spanning more than 24 hours To set alarm recording Setting alarm recordingTimer recording using an external timer Maximum number Alarm REC Mode SET screen is displayedAlarm recordings Set REC Rate and Duration Set Alarm InterleaveWhen alarm recording settings have been completed To set pre-alarm recording Cursor moves to recording rate and duration When pre-alarm recording settings have been completedREC Rate for PRE-ALARM Recording flashes Default setting 1 MIN Cursor moves to Alarm Trigger Setting the alarm trigger Setting the motion sensors Use this procedure to set other sensor positions To B Cursor moves to ModeFlashes for the Mode „ To stop motion sensor recording Example Alarm Setting alarm operation and displaySetting alarm display OFF flashes in the Alarm Retrigger field First Canceling alarmsCursor moves to Alarm Priority Switch EXIT/OSD button Shuttle dial General settingsSetting data display General SET Display SET screen is displayed Setting display for video lossGeneral SET Perform the following if so required Disk Error default setting on Setting the buzzerAlarm default setting OFF Disk Full default setting on Example Setting 123456AB as a password Setting the security lock„ Operation after setting passwords Setting the administrator password Turn the jog dial to move the cursor to User Use the same procedure to set 123456ABFollowing this, turn the shuttle dial clockwise Turn the jog dial to select on Turn the jog dial to move cursor to Turn the jog dial to move cursor to REC Control HDD SET screen is displayed Cursor moves to Disk Initialize Setting and initializing the hard diskInitialization of hard disk erases all contents Initializing the hard disk Making network connections Network settingsExpanding the hard disk capacity Making network settings Set Port Set IP AddressSet Subnet Mask Set Gateway General SET screen appears Setting RS-485When setting has been completed, press the EXIT/OSD button Cursor moves to Alarm Info Protocol field flashes Setting camera controlCursor moves to Address Camera Control SET screen is displayed BBV Coax ADD. column flashesSanyo Coax Sanyo RS485 Finishing dome camera operation When zoomingPress the FUNC. button Operating dome cameras with the digital video recorder Example Displaying Camera No in quad position Setting quad, multi 9 and 16 displaySetting multi screen positions Screen SET Checking modified screen positions 101Screen SET Automatic selection is set to a period of 5 seconds Setting the automatic selection periodSetting the main monitor and monitor 1S flashes Starts to flash for Time Period 103MAIN/MON.2 Monitor SET screen is displayed Mask SET screen is displayed Setting masksCursor moves to Mask SET Color Level SET screen is displayed Setting the color level105 106 Displays the total amount of running time for disk Power LOSS/USED TimePower LOSS/USED Time screen is displayed 107 Operation class Initialization LOGArea CompactFlash card Copy Menu SettingsSaving menu settings on a 109 Turn the jog dial to select Load Copy Menu SettingsLoading settings from a CompactFlash card When copying recording area settings Data format Interface SpecificationsRS-485 specifications 111 Sanyo protocol command table Interface Specifications 113 SpecificationsSpecifications 420 365 Specifications DimensionsUL disclaimer statement Units mm „ Example Recording to a 80 GB hard disk 100%-usage Specifications115 Table of recording rate and times „ Example Recording to a 300 GB hard disk 100%-usage 116 Program recording rate Table of recording rate settings117 FPS field/sec Table of pre-alarm recording timesMinutes 10s 20s 40s 119 Terminal board specifications 120 121 Menu Setting Sequence General SET →P.86 Menu Setting SequenceHDD SET →P.92 RS-485 SET →P.96 Mask SET →P.104 123 Index Index Setting recording conditions Setting the color levelTime/date search Timer recording Timer settings