Turn the jog dial to select Preview | Sanyo DSR-3716, DSR-3709

5SEARCHING FOR RECORDED VIDEO

6 Turn the jog dial to select “PREVIEW”.

<MOTION DETECTION SEARCH>

SEARCH FROM : ALARM		/ CHANNEL : 4
START :
01-05-04 10:00
END :
01-05-04 20:00
MOTION SENSOR	->
PREVIEW	->
VIEW	->

MOVE:JOG SELECT:SHUTTLE

7 Turn the shuttle dial clockwise.

Each time the shuttle dial is turned clockwise, a different motion sensor screen will be displayed on the preview screen.

If “NOT FOUND” is displayed

Carry out motion sensor setting again.

Viewing video detected by the motion sensor on a full screen

8 Turn the jog dial to select “VIEW”, and then turn the shuttle dial clockwise.

Normal playback will be started for the specified recording.

zBy specifying a camera number (or channel) and performing MOTION DETECTION SEARCH, playback can be carried out for only the specified camera number.

In such a case, the title information, date information, and/or time information may partially disappear.

zTo playback a recording from a different camera, stop the current playback and then repeat the setting process from the beginning.

English

37

Image 38

Sanyo DSR-3716 Turn the jog dial to select Preview, „ If not Found is displayed, Carry out motion sensor setting again

Contents

Page Precaution Service Symbols used in this manual Main featuresAccessories Introduction Contents Contents Settings Other „ Handling a detached HDD unit Before USE„ Notes on replacing the HDD Hard disk and cooling fan are consumable components Backup batteryBefore USE Important recordings Front panel Names and Functions of PartsDSR-3716 Names and Functions of Parts DSR-3709 Menu Reset button JP.48 Timer button and indicator JP.23Alarm buttons JP.31 Jog dial inside and shuttle dial outside z During playback Rear panel Basic connections Installation and ConnectionsConnecting RS-485 terminals Pin locations Connection Installation and ConnectionsRS-485 termination switch settings Cable types Connecting Alarm in terminals Connecting Sanyo protocol devices Dome CamerasConnecting an amplifier Amp Sold separately Connecting the power cord Connecting Sensor Alarm OUT terminalsConnecting Control terminals Operation display area 01-01-04 000000 REC Repeat EN a AlarmPreparing for USE Changing the language Preparing for USEChanging the position of the operation display area Setting the time Example Setting 830 on October 26 Hard disk recording areas Alarm recording areaInternal hard disk Normal recording area Viewing on quad screens Viewing Video from a CameraViewing on a full screen Press the No Camera Select button Viewing on plus screen Viewing Video from a CameraViewing on multi screens 9 screens/ 16 screens Press the Sequence button Viewing with automatic screen selectionViewing on the monitor Press the Sequence button once again Ending the monitor 2 setting procedure Set MON.2 Display from Alarm Operation SET to ON. JP.84Displaying alarm video in full screen format Selecting Camera No for full screen Recording Timer recordingPress the Timer button Normal recording End alarm recording Alarm recordingSet alarm recording When an alarm signal is detected If an alarm is detected Pre-alarm recordingSet pre-alarm recording Alarm Full indicator Fast-forward and fast-rewind playback PlaybackPlaying video on a full screen Press the PLAY/STOP button Enlarging the playback video PlaybackChanging the playback speed Move the zoom frame to the area to be magnified Press the Still button during playback Viewing still imagesPress the Zoom button Press the Still button once again Press the Quad button during playback Performing frame advance forward or reversePlaying video on multiple screens Searching for Recorded Video Searching from the Search screen Searching for Recorded Video Alarm searchPress the appropriate Alarm button during playback Turn the jog dial to select the video for playback Alarm number for the selected recording will start to flash Alarm thumbnail searchTurn the jog dial and select Alarm Thumbnail Search Time/date search View If no recording exists for the specified time Turn the jog dial to select Archive Area Search Archive area searchMotion detection search Selected image is displayed on the preview screen Start Example AlarmExample END Set the motion sensor to use for searching „ If not Found is displayed Carry out motion sensor setting againTurn the jog dial to select Preview Copying video to a CompactFlash card or Microdrive JP.41 Saving Copying Recorded VideoCopying video to the hard disk’s archive area JP.39 Copying video to a CD-R/RW JP.45 Press the Copy button Saving Copying Recorded VideoCopying video to the hard disk’s archive area Example Copying a specified 10-second portion of video „ To cancel a copy operation Turn the jog dial to select Seconds Insertion method Removal method Copying video to a CompactFlash card or MicrodriveInsert a CompactFlash card When this has been completed, Copy Finished ! is displayed ‹PICTURES Printing images from CompactFlash cards quick print Viewing images copied to a CompactFlash card on a PC Dcim Turn the jog dial to select the unit Copying video to CD-R/RWConnect a recordable CD-R/RW drive and insert a disk Viewing images copied to a CD-R/RW on a PC Formatting a CompactFlash card and CD-RW Basic menu operations Menu Configuration and OperationsMoving from the Main Menu to a sub-menu or setting screen Turn the jog dial to select a menu Movement and confirmation in sub-menus and setting screens Menu Configuration and OperationsRestoring menu setting items to their default values Entering numbers with the numeric keys Sub-menu configuration Main menu Sequence SET Sub menu Setting item Settings or display contentMulti Screen Color Level JP.105 Initial SET is used to make the following setting Initial settingsSetting the daylight saving Initial SET When USE is selected for Daylight Saving Turn the jog dial to select Mode under Daylight SavingTurn the jog dial to change the settings Initial SET Cursor moves to the time External clock settingTurn the jog dial and move the cursor to ADJUST. Time To C Terminal To Clock SET in terminal Detecting connected cameras Displayed Turn the jog dial to select H Setting camera titlesExample Setting the title HALL-1F for Camera No Repeat steps 5 and 6 to enter the remaining characters Example Setting November 17 as a holiday Setting holidaysTurn the shuttle dial clockwise after setting Set the month and day for item No Setting time periods Time Period a settings Set T-1 to 6 AM Time period settingsExample 1 Setting periods using Time Period a Cursor moves to Mask Time period operations settingsTime Period a flashes Camera Select buttons Timer button Jog dial Settings for recordingNormal recording easy setup Record SET Record SET Setting based on recording daysCursor moves to Timer Recording DLY Record SET screen is displayed Turn the shuttle dial counter-clockwise Set Picture QualitySet Audio Recording Example on Setting based on recording rate Recording Area SET screen is displayed AlarmDisplaying the recording areas „ Recording area allocations „ Default hard disk settingsChanging recording areas „ If the normal recording area is set to 0% Turn the shuttle dial counter- clockwise Setting overwrite permissionCursor moves to Area Full Reset Hard disk is initialized Setting recording conditions Setting overwriting for the normal recording area OFF 01-01-04 000000 REC 1%Display area Capacity Setting series recording Set depending on your recording needs Starting and stopping series recording Turn the jog dial to select the storage period Setting auto deletingSetting normal recording Turn the shuttle dial clockwise Press the EXIT/OSD button Example P-1 Set REC RateSet REC Program Group Selects Program No through Program No Setting program recordingCameras No through No are available for the DSR-3709 Cursor moves to 0.5 from Select Individual Camera Rate FPS Timer settings Timer setting items SUN from the Week column flashes „ To change a displayed setting itemTimer SET screen is displayed Cursor moves to the SUN row Start time flashes as Timer reservations spanning more than 24 hours Make settings in the Week and Start columnsTo cancel all set timer reservations All setting items are cleared Menu Reset button To set alarm recording Setting alarm recordingTimer recording using an external timer Maximum number Alarm REC Mode SET screen is displayedAlarm recordings To set pre-alarm recording Set Alarm InterleaveWhen alarm recording settings have been completed Set REC Rate and Duration Default setting 1 MIN Cursor moves to Alarm Trigger When pre-alarm recording settings have been completedREC Rate for PRE-ALARM Recording flashes Cursor moves to recording rate and duration Setting the motion sensors Setting the alarm trigger Use this procedure to set other sensor positions „ To stop motion sensor recording Cursor moves to ModeFlashes for the Mode To B OFF flashes in the Alarm Retrigger field Setting alarm operation and displaySetting alarm display Example Alarm Switch Canceling alarmsCursor moves to Alarm Priority First General SET General settingsSetting data display EXIT/OSD button Shuttle dial Perform the following if so required Setting display for video lossGeneral SET Display SET screen is displayed Disk Full default setting on Setting the buzzerAlarm default setting OFF Disk Error default setting on Setting the administrator password Setting the security lock„ Operation after setting passwords Example Setting 123456AB as a password Turn the jog dial to select on Use the same procedure to set 123456ABFollowing this, turn the shuttle dial clockwise Turn the jog dial to move the cursor to User Turn the jog dial to move cursor to REC Control Turn the jog dial to move cursor to Initializing the hard disk Setting and initializing the hard diskInitialization of hard disk erases all contents HDD SET screen is displayed Cursor moves to Disk Initialize Making network connections Network settingsExpanding the hard disk capacity Making network settings Set Gateway Set IP AddressSet Subnet Mask Set Port Cursor moves to Alarm Info Setting RS-485When setting has been completed, press the EXIT/OSD button General SET screen appears Camera Control SET screen is displayed Setting camera controlCursor moves to Address Protocol field flashes Sanyo RS485 ADD. column flashesSanyo Coax BBV Coax Operating dome cameras with the digital video recorder When zoomingPress the FUNC. button Finishing dome camera operation Screen SET Setting quad, multi 9 and 16 displaySetting multi screen positions Example Displaying Camera No in quad position Checking modified screen positions 101Screen SET 1S flashes Setting the automatic selection periodSetting the main monitor and monitor Automatic selection is set to a period of 5 seconds Starts to flash for Time Period 103MAIN/MON.2 Monitor SET screen is displayed Mask SET screen is displayed Setting masksCursor moves to Mask SET Color Level SET screen is displayed Setting the color level105 106 107 Power LOSS/USED TimePower LOSS/USED Time screen is displayed Displays the total amount of running time for disk Operation class Initialization LOGArea 109 Copy Menu SettingsSaving menu settings on a CompactFlash card When copying recording area settings Copy Menu SettingsLoading settings from a CompactFlash card Turn the jog dial to select Load 111 Interface SpecificationsRS-485 specifications Data format Interface Specifications Sanyo protocol command table 113 SpecificationsSpecifications Units mm Specifications DimensionsUL disclaimer statement 420 365 Table of recording rate and times Specifications115 „ Example Recording to a 80 GB hard disk 100%-usage 116 „ Example Recording to a 300 GB hard disk 100%-usage Program recording rate Table of recording rate settings117 FPS field/sec Table of pre-alarm recording timesMinutes 10s 20s 40s Terminal board specifications 119 120 Menu Setting Sequence 121 RS-485 SET →P.96 Mask SET →P.104 Menu Setting SequenceHDD SET →P.92 General SET →P.86 Index 123 Index Setting recording conditions Setting the color levelTime/date search Timer recording Timer settings