DXC-D35P/D35WSP(CE)

DXC-D35/D35WS(UC)

V1

 

Chapter 4 Viewfinder Screen Indications and Menus

Viewfinder Normal Indications

Only when connecting the DSR-1/1P

Indication

Meaning

50P CONNECT

Connection with the PRO 50-pin

 

connector on the DSR-1/1P.

 

(Freeze mix function is disabled.)

MP TAPE

An incorrect type of cassette has

 

been loaded. (The cassette is

 

automatically ejected and the

 

indication disappears in about two

 

seconds.)

CLIP DATA ERR

Abnormality of the cassette memory

 

data.

AUDIO 48kHz?

At back space editing, audio

(4 flashes/s)

recording mode has changed from

 

32 kHz mode (4-channel mode) to

 

48 kHz mode (2-channel mode).

AUDIO 32kHz?

At back space editing, audio

(4 flashes/s)

recording mode has changed from

 

48 kHz mode (2-channel mode) to

 

32 kHz mode (4-channel mode).

ERROR:91-13F

Failure in loading or saving the

 

cassette memory data.

 

When other error indication

 

appears, refer to the operating

 

instructions for the DSR-1/1P.

CLIP CONT?

Asking whether you will continue

 

shooting in ClipLink mode or not

 

when the cassette contains ClipLink

 

data. (The indication disappears

 

when you press the ClipLink

 

CONTINUE button on the DSR-1/

 

1P or start the next shooting without

 

pressing it.)

CLIP NEAR END

At back space editing in ClipLink

 

mode, capacity for only 1 to 3 index

 

pictures remains.

CLIP END

Impossible to record any more clip

 

shots.

qf White balance indication The following indications appear.

Indication

Meaning

EZ

Operating in EZ mode (The ATW function is

 

selected.)

ATW

The ATW function is selected. (The ATW

 

button was pressed and the indicator is lit.)

W:A

White balance memory A is selected.

W:B

White balance memory B is selected.

W:P

Preset white balance is selected.

W:M

Manual adjustment is performed remotely.

qg SKIN DTL indication

This appears when the skin detail function is activated (The SKIN DTL switch is set ON.)

qh EVS indication

This appears when the EVS (Enhanced Vertical definition System) function is enabled. (See page 84.)

qj Lens f-stop indication

This shows the f-stop of the lens.

Note

Depending on the lens being used, this indication may differ slightly from the actual f-stop on the lens.

qk Gain indication

This shows the gain value, and the settings of the HYPER GAIN switch and the DPR (Dual Pixel Readout) function (see page 64) as shown in the following table.

Example indication

Meaning

18dB

Gain setting is 18 dB.

DPR 18dB

The DPR function is enabled.

 

In this case the DPR function

 

approximately doubles the gain (an

 

increase of 6 dB) over the current

 

gain setting (in this case 18 dB).

HYPER

The HYPER GAIN switch is in the

 

ON position.

 

In this case the hyper gain function

 

increases the gain by a factor of

 

about 60 or 120 with respect to 0

 

dB regardless of the current gain

 

setting (that is, increased to 36 or

 

42 dB).

ql Filter setting indication

This shows the setting of the FILTER control.

Indication

Filter setting

3200

1

(3200K)

56ND

2

(5600K

+ 1/8ND)

5600

3

(5600K)

56ND

4

(5600K

+ 1/64ND)

w; Clock indication

The clock indication is shown in one of the following ways (according to the CLOCK IND setting of CAM, BARS, or OFF in advanced menu page 8).

CAM: Always displayed.

BARS: Displayed whenever color bars are displayed.

OFF: Not displayed.

If the clock indication is displayed during recording, it is recorded onto the image.

wa Voltage/error indication

The current voltage is displayed whenever the camera head’s power supply voltage dips below 11.0 V DC. However, you can also display the current voltage at any time by pressing and holding the MENU/STATUS switch in the upward position (the display is shown for as long as you hold the switch upward).

An error message is displayed when an abnormality has been detected by the auto diagnostic function (page 62).

If an error message appears, contact your Sony dealer.

If using a VTR and an Anton Bauer Intelligent Battery System

The remaining battery capacity is shown as a percentage.

ws Shutter setting indication

When the SHUTTER switch has been set to ON, the shutter speed, CLS frequency or EVS set in basic menu page 1 is displayed here.

Status Indications

If you set the MENU/STATUS switch to STATUS while a menu is being displayed, the camera head’s current setting status will be shown in this display area.

a)When both the DCC+ and DynaLatitude functions are set to OFF

Display

Description

 

WHITE

White balance adjustment method

 

 

selection (PRE/A/B) and color

 

 

temperature during auto white

 

 

 

 

 

 

balance adjustment

 

 

 

 

 

 

 

A.IRIS

Iris adjustment method selection

 

 

 

 

 

 

(STD/SPOT L/BACK L)

 

 

 

 

 

FILE

STD (when not using the setup files),

 

 

 

 

 

 

 

or a selected file name (when using

 

DCC+ or DL

For DCC+ indication: ON with the

Chapter

 

the setup files) (see page 71).

 

 

OUTPUT/DL/DCC+ switch set to

4

 

CAM/DCC+ (DCC+ON), and OFF with

Viewfinder

 

 

 

the switch set to CAM/DL and DL in

 

 

advanced menu page 2 (page 64) set

 

 

to OFF (both DCC+ and DynaLatitude

Screen

 

OFF).

 

For DL indication: When setting the

 

 

OUTPUT/DL/DCC+ switch to DL and

Indications

 

HIGH is displayed according to DL

 

DL in advanced menu page 2 to OFF

 

 

(DynaLatitude OFF), LOW, STD or

 

 

LEV setting in basic menu page 2

and

 

(page 59).

 

Menus

 

 

56 Chapter 4 Viewfinder Screen Indications and Menus

Chapter 4 Viewfinder Screen Indications and Menus 57

1-29

Page 37
Image 37
Sony DXC-D35 service manual Viewfinder Normal Indications, Status Indications