Sony DXC-D35 service manual Advanced Menu Operations, Advanced menu, To change

DXC-D35P/D35WSP(CE) DXC-D35/D35WS(UC)

Viewfinder Advanced Menu

Bring up the advanced menu pages by setting the POWER switch to ON while pressing the UP/ON button up (see page 52).

Advanced menu page 1

Use this page to return all advanced menu settings to

Advanced menu page 3 Advanced menu page 4

There are up to 15 advanced menu pages (the number displayed depends on the switch settings and the type of connected VTR).

Note on EZ mode

their factory preset values.

For details of this operation, see “Displaying the advanced menu and switching to the normal indications” (page 52).

a)

￿

cPAGE4 (NEXTcV PREVcv)￿

￿
MARKER	: CENT/90%￿
LIMITS	: OFF￿
ZEBRA	:	1 ￿ a)
ZEBRA1	: 70IRE		￿
￿
VF S DTL: ± 0￿
VF TALLY:		× 2￿
VF PLAY	:	Y￿

When the camera is in EZ mode, the advanced menu does not appear. Release the EZ mode beforehand. (See page 14.)

Advanced Menu Operations

To change the page

Move the cursor to the menu number, then press the UP/ON button or the DOWN/OFF button.

Pressing the UP/ON button displays the previous page and pressing the DOWN/OFF button displays the next

Advanced menu page 2

a) For DXC-D35P/D35WSPL: EBU75
Item	Settings
AWB MEM	2 (normal value): No
Selects whether or not to	correspondence with FILTER
make the FILTER knob	knob settings. Only two
settings (1 to 4) correspond	adjustment values (A and B)
to separate white balance	are stored in memory.
adjustment values stored in	2 × 4FL: Correspondence
memory.	with FILTER knob settings.
	Each of the four knob
	settings can be used to set A
	and B adjustment values, for
	a total of eight settings.
TONE	ON (normal value): Output
Selects whether or not to	audio signal.
output a 1-kHz audio signal	OFF: Do not output audio

LENS SEL:	1￿
￿
EXIT MENU (YEScv)
a) For DXC-D35P/D35WSPL: 70%
Item	Settings
MARKER	CENT/90% (normal value):
Selects ON/OFF setting for	Displays center marker and
center marker, size setting	safety zone marker at 90%
(percentage of viewfinder	size.
screen area), and display	CENT/80%: Displays center
ON/OFF setting.	marker and safety zone
	marker at 80% size.
	90%: Displays only safety
	zone marker at 90% size.
	80%: Displays only safety
	zone marker at 80% size.
	CENT: Displays only center
	marker.

Chapter 4 Viewfinder Screen Indications and Menus

page. Pressing the DOWN/OFF button when the last page is being displayed returns the display to the first page.

To select items in a page

Press the MENU/STATUS switch to move the cursor among the menu items.

To change settings

This operation is the same as for the basic menus.

For a description of basic menu operations, see page 58.

To return to the normal indications

Move the cursor to EXIT MENU, then press the UP/

Item Settings

GAIN

This sets gain values for the positions of the GAIN switch. The HIGH, MID, and LOW values must be set so that LOW < MID < HIGH.

LOW	–3 dB, 0 dB (normal
Sets the L position.	value), 3 dB, 6 dB, 9 dB, 12
	dB, 18 dB, 18 dB + DPR, 24
	dB
MID	0 dB, 3 dB, 6 dB, 9 dB
Sets the M position.	(normal value), 12 dB, 18
	dB, 18 dB + DPR, 24 dB, 24
	dB + DPR
HIGH	3 dB, 6 dB, 9 dB, 12 dB, 18
Sets the H position.	dB (normal value), 18 dB +
	DPR, 24 dB, 24 dB + DPR,

with the color bars when the	signal.
OUTPUT/DL/DCC+ has
been set to BARS.
BARS	SMPTE (normal value for
Selects normal width or	DXC-D35/D35WSL):
narrower width for color	Normal width
bars.	EBU75 (normal value for
	DXC-D35P/D35WSPL): EBU
	75%
	EBU100 (for DXC-D35P/
	D35WSPL): EBU 100%
	SPLIT (for DXC-D35P/
	D35WSPL): Not for normal
	operation
	SNG: Narrower than normal
	(used for satellite
	communications, etc.)
REMOTE1	REC (normal value):
Sets a function for position 1	Specifies recording start/stop
of a switch connected to the	MARK: Specifies a Mark IN/
REMOTE1 connector.	OUT point.
	CUE: Specifies a cue point.
	NG: Specifies NG/OK.

LIMITS (For DXC-D35WSL/ D35WSPL)

Selects the safety zone size when the scan size is 16:9.

ZEBRA

Selects type of zebra pattern display.

ZEBRA1

Sets base level for zebra pattern 1.

OFF (normal

value):FDepends on the scan size.

4:3, 13:9, 14:9, 15:9

1 (normal value): Displays the zebra pattern over parts having a video level. between 70 and 90 IRE (or 70 and 90%).

Use the next item (ZEBRA1) to select the base level.

2:Displays the zebra pattern over parts having video levels of 100 IRE or above

( or 100% or above). 1/2: Dual display (both 1 and 2)

70 IRE (normal value) to 90 IRE or 70% (normal value) to 90%

Can be set for each IRE step or 1% step.

Chapter 4 Viewfinder Screen Indications and Menus

ON button.

Contents and Settings of Each Page

Each page’s contents and settings are described below.

64 Chapter 4 Viewfinder Screen Indications and Menus

	HYPER GAIN
HYPER	36 dB (normal value), 42
Sets gain value when the	dB
HYPER GAIN is selected.
DL	ON (normal value), OFF
Sets DynaLatitude function	When set to ON, the amount
ON/OFF.	of DynaLatitude effects is
This setting is valid only	set in basic menu page 3
when the OUTPUT/DL/	(see page 59).
DCC+ switch has been set to
DL.

REMOTE2	REC: Specifies recording
Sets a function for position 2	start/stop.
of a switch connected to the	MARK (normal value):
REMOTE1 connector.	Specifies a Mark IN/OUT
	point.
	CUE: Specifies a cue point
	NG: Specifies NG/OK.
BAUD RATE	9600, 38400 (normal value)
Sets a baud rate for a
computer connected to the
REMOTE connector 2 (to be
supported in future version).

VF S DTL	–99 to ±0 (normal value) to
Sets the detail level of	+99
images on the viewfinder	Negative values set softer
screen (displayed only when	edges and positive values
a viewfinder other than the	set sharper edges.
DXF-701/701CE/701WS/
701WSCE/801/801CE is
attached).
	(continued)
Chapter 4 Viewfinder Screen Indications and Menus 65

1-33