|
|
|
|
| ||
| Table |
|
| |||
|
|
|
|
|
|
|
|
| IRQ3 | MEMORY | I/O | OPTION |
|
OPTION BOARD |
| ADDRESS | ADDRESS | SLOT |
| |
SMC8416BTA (1st)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | EISA Slot J3 |
|
SMC8416BTA (2nd)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | EISA Slot J4 |
|
DigiBoard (1st) |
| Not Required | D0000 | 200 | EISA Slot J5 |
|
DigiBoard (2nd) |
| Not Required | D0000 | 220 | EISA Slot J6 |
|
SMC 8432BTA (1st)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J9 |
|
SMC 8432BTA (2nd)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J10 |
|
SMC 8434BT (1st)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J9 |
|
SMC 8434BT (2nd)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J10 |
|
SMC 9332BDT (1st)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J9 |
|
SMC 9332BDT (2nd)4 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J10 |
|
Adaptec 2940UW1 |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J115 |
|
Mylex DAC960PDU |
| Set by BIOS | Set by BIOS | Set by BIOS | PCI Slot J11 |
|
Onboard 7880 SCSI |
| Set by BIOS | Set by BIOS | Set by BIOS | N/A2 |
|
Onboard 7860 SCSI |
| Set by BIOS | Set by BIOS | Set by BIOS | N/A2 |
|
1.When more than 1 SCSI controller is plugged in, use IRQ 14 for secondary controller
2.For disk controllers plugged into slots and the onboard disk controllers, the sequence for BIOS scanning to determine the primary (Boot) disk controller is:
EISA slots J3 through J6
PCI slot J11
Onboard 7880 SCSI
PCI slots J10 through J8
Onboard 7860 SCSI
PCI slot J7.
It is recommended that the BIOS be disabled on all SCSI controllers except for the controller with the boot disk drive attached (see The SCSISelect Utilities in the Configuring Your System chapter. This saves memory address resources and provides control over the boot device independent of board slot locations.
3.Additional IRQ’s can be made available as follows:
Disabling Comm Port 1 = IRQ4 is available Disabling Comm Port 2 = IRQ3 is available Disabling Parallel Port = IRQ7 is available.
4.A maximum of three LAN channels consisting of any combination of single or dual channel. Install EISA LAN card in the first available EISA slot from the bottom. Install PCI LAN card in the first available PCI slot from the top.
5.A maximum of two SCSI controllers may be installed. Install the first controller card in the top PCI slot and the second controller in the second from the top PCI slot.