Requirements for the SAT, Display, Keyboard | AT&T R1V2 specification

Requirements for the SAT

This section defines requirements for the system administration terminal (SAT). Any data terminal with an RS-232C interface that meets the requirements below may be used as the SAT.

Display

System 25 administration requires the following display characteristics:

■Minimum display size of 16 lines by 80 columns

■Ability to display upper case ASCII alphabetic characters, ASCII numeric, and some other ASCII symbols (see Keyboard below)

■Carriage return and line feed characters are required to position the cursor at the start of a new line

■Full duplex operation.

Keyboard

System 25 administration requires keyboard input that includes alphanumeric characters and some basic ASCII symbol characters. Your administration terminal should be capable of sending the following ASCII characters:

A-Z or a-z	-	Used to access various commands
0-9	-	Menu selection and command parameters
*, #	- Non-numeric telephone dial characters

•- “Wildcard” character

?	-	Causes additional information to be displayed
BACKSPACE	-	Corrects errors in typing
RETURN	-	Completes entry of numeric information
„	-	Text input (Display Support and Password Administration)
	-	Text input (Display Support and Password Administration)

SAT Port Speed Setting

The data transfer rate for terminals or personal computers is set after a carriage return character is entered from the device keyboard. Two data transfer rates are supported–1200 baud and 300 baud. The default rate is 1200 baud.

Switch Settings for the AT&T Model 703 SAT

There are two sets of switch settings to check on the AT&T Model 703 SAT.

The three rocker switches at the upper right of the keyboard are set as follows: A) LOCAL COPY–press down left side of switch, B) ON LINE–press down right side of switch, C) UPPER CASE–press down left side of switch.

Four pencil switches under the paper compartment cover are set as follows: switches 1 and 3 to OFF; switches 2 and 4 to ON.

For more specific instructions, see the user’s guide that was packaged with the SAT.

Requirements for the SAT 17-1

Image 152

AT&T R1V2 Requirements for the SAT, Display, Keyboard, SAT Port Speed Setting, Switch Settings for the AT&T Model 703 SAT

Contents

AT&T System 1987 AT&T All Rights Reserved To Order Copies of this Document Refer to Document Number FCC Warning Statement Order Number System 25 DocumentsDocument Contents Administering Trunks Administering Auxiliary EquipmentAdministering Voice Stations Administering Data Line Starlan CP Ports 10-1 10-3 10-6 10-10 10-11 12-2 12-6 12-8 Administering Attendant EquipmentAdministering Button Assignments 13-1 13-2 13-3 13-4 16-1 16-3 Administering Tape Save/Restore OperationsRequirements for the SAT Index Implementation Planning Forms System Administrator’s RoleIntroduction Using this Manual Conventions Used in this Manual How to Use the System Logging In to System Strange Output Correcting Typing ErrorsMaking Backup Tapes System 25 Administration Main Menu Main Menu Items Administration Commands Selecting a Main Menu Item Command Functions Entering CommandsChanging an Action Number Changing a Data Value Changing a Target Value PDC DGC Action Groups Lists Display Support IDsLists, Searches, and Port Removal Searches Removing Ports Error Messages System Responses Print Messages Initializing the System Default TranslationsFull-Default Cold Start Limited Default Cold Start Port Default CodeUnassigned Trunk Ports Station Dial Codes To Initialize the System Initialization SequenceBegin with a Cold Start Be sure to record port assignments on the trunk forms Be sure to record port assignments Terminal or data terminal forms as you assign them 2Initialization SequenceEach station’s port assignment on the individual voice Smdr Administering System-Wide OptionsToll Restriction Options Call Coverage Options Pooled Modem Options Date Time of Day Call Accounting Options Account Codes Expert Mode Prompt Miscellaneous System Options Administration Password Toll Calls Allowed TCA Lists Floating PDCs FPDCs Display Support Virtual Facilities System Speed Dialing Administering Trunks Assigning a Trunk 1Trunk-Type Codes If the Trunk Type is You Enter Removing a Trunk Assigning Class of Service to did TrunksAssigning Class of Service to All Other Trunks 2Trunk Class of Service for all trunks except did Dial Access Class-of-Service OptionsPooled Facility Access Delay Announcement Type of Incoming Assigning Trunk Options to a Slac System Administering Auxiliary Equipment External Alerts Port Type Paging Associated with Auxiliary Trunk Port DGC Delay Announcement Directed Night Service Delay AnnouncementPaging Associated with CO Trunk Port Music-on-Hold Dictation Pooled ModemAdditional Tone Detector Administering Voice Stations Adding a Voice Station Display Support Removing a Voice Station1Voice Terminal Type Codes Terminal Type Code Changing a Station Dial Code Calling Restrictions Assigning Class of Service OptionsMoving a Voice Station Features Extended/Off-Premises Level Allowed FRL Pools Night Service To display Station Hunting ToGroup Call Coverage To Call Pickup To assign Multiline Voice Stations Features Level Allowed FRL Pools At Action = , enter 7. ‡ At Data = , enter Enter 6 Administering Data Line and Starlan CP Ports Adding a Data Station Removing a Data Station Changing a Data Dial Code Moving a Data Station Assigning Class-of-Service Options Assign Calling Restrictions To restrict access to all To assign ARS Facility Enter 1 for Yes or 0 for no. The default is Bps? Set Baud Rate and Parity Assign Other Data Features At Action = , enter 77. ‡ Administering Attendant Equipment Default Attendant Assignments Assign a Switched Loop Attendant Console Assign a Second Attendant Console Move an Attendant Console Change an Attendant PDCRemove an Attendant Console PDC Assign a Direct Extension Selector Consoles Assign Class-of-Service to an Attendant Console Assign Attendant Options Dtac and Slac 30@ Switched Loop Attendant Console Options To assign a did access code to the Slac 1Standard Call Type Defaults 2Message-Center-Like Call-Type DefaultsSlac Call-Type Options Slac Assigning Message-Center-Like Defaults Setting Call-Type Options To specify which Administering Button Assignments Assigning Features to ButtonsDefault Button Assignments MET Sets Selector Console DXS First and Second DXS Consoles Button Assignment Tables 1Multi line Set Button Defaults2Switched Loop Attendant Console Button Defaults Type 3Direct Trunk Attendant Console Cold Start Defaults Message† Drop† Conference† Transfer† Hold† 5DXS Console Button Defaults6MET Set Button Defaults SYS ACC-O Pers Line AG Exclusion MSG Enter 1 0 Send ALL Calls AG 12. † DSS Assigning Attendant-Console-Specific Buttons Assigning Selector DXS Console Buttons Enter Administering Direct Group Calling DGC Groups To disable DGC queuing Administering Automatic Route Selection ARS ARS Patterns Define Subpattern a FRL FAC Define Subpattern B Remaining ARS Patterns 230 Home Area Code Exception List Area Code Routing Table 512. ‡ Other Area Codes Exception List ARS Digit Translation Tables 703. ‡ Administering Tape Save/Restore Operations Using the Digital Tape UnitSave/Restore Verify Save Your Translations Verify Saved Translations Restore the System Translations from a Backup Tape Calls in progress will be dropped Type c Line now reads System Searches Search functions PDCs of Stations that Hunt to a Specified Station PDCs of Call Pickup Group Member Stations Initiate Search Translated Board At Data = , enter PDC of the station with the buttons Enter Alarms Search for Display Support SearchesMatching Display IDs Display ID for a Trunk Listing Circuit Packs Administering RS232 Parameters Target At Data = , enter 300, 1200, 4800, or Command Reference List of Tables Default Dial Code Assignments 1PORT/PDC Administration, Voice Terminals Menu=1/2 Csspp16 0 for none PDC 0 for none 2Voice Terminal Type Codes If the Terminal Type is Code 3Feature Button Translation Menu=1/2 101 310 Feature Button Translation Menu=1/2 Join Destination Local Scroll Last # Dialed LOOP† ALARM† LOCAL† SCROLL† 4Multiline Set Button Defaults5Switched Loop Attendant Console Button Defaults Type RTN-DA† Pool 8MET Set Button Defaults E S T † 9PORT/PDC Administration, Data Terminals Menu=1/2 For none =2 short Breaks 10Data Port Type Codes If the Data Port Type is Code 11Port Administration, Trunks Menu=1 32 0 for none0=won’t ring Only 12Trunk Type Codes If the Trunk Type is 13 Trunk 14Port Administration, Auxiliary Equipment Menu=1 21-27 15Special Feature Port Type Codes FeatureZTN78 ZTN76 ZTN77 PORTS, Station/Trunk/Special Port Circuit Board Options See -17,Applicable Options ZTN85 17Applicable OptionsCircuit Board Action Type ZTN76 18PDC Administration Menu=2 System Administration Menu=4 800-807 19System Administration Menu=4 CommandHhmm Mmddyy =neither See Tables 21Message-Center-Like Call-Type Defaults 20Standard Call Type DefaultsFor Switched Loop Systems only Fpdc 22Floating PDC Administration Menu=523Direct Group Calling DGC Administration Menu=6 24Toll Calls Allowed TCA List Administration Menu=7 25Searches Action Items Menu=8 LDN only PDC/DDCPDC / DDC / Fpdc / DGC 26Board Type-Wildcard Representation EmptyStation Special 27Port/Board Type-Specific Representation Voice Station Starlan CP, DLC Systems Technician only 28Save/Restore and System Restarts Menu=929RS232 Port Administration Menu=10 30Automatic Route Selection Administration Menu=11 401 402500 501 SAT Port Speed Setting Switch Settings for the AT&T Model 703 SATRequirements for the SAT Display Index Index I 2I n d e Index 4I n d e