Section 3 - Operation EIC - Calibration
2. | Slip percent threshold |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 |
|
| ||||
On tractors equipped with an optional radar speed |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
sensor, the slip alarm can be used to notify the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
operator whenever the wheel slip percentage is above |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
a certain threshold.. |
|
|
|
|
|
|
|
| 2 |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
1. | To set the slip alarm threshold, enter the desired |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| maximum percent slip (1).. The selected (flashing) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| digit can be changed by touching the UP and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| DOWN arrow buttons (2).. Other digits may be | 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| selected by touching the LEFT and RIGHT arrow |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| buttons (3).. The alarm can be disabled entirely by |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| setting the threshold value to zero.. | 3 | 4 | |||||||||||||||||
2. | Once the desired threshold value has been entered, | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| touch SELECT button (4) to confirm the change.. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
3. Setting the service alert intervals
The two service alert intervals can be used to remind the operator that regular scheduled maintenance is required.. The service alerts are based on engine hours.. If, for example, a service alert is set to 50 hour intervals, it will become active at 50 hours, 100 hours, 150 hours, etc.. Once a service interval becomes active, the word “SERVICE” (5) will flash in the lower portion of the central display until the alert is cleared by the operator..
1.To set a service alert interval, enter the desired number of hours.. The selected (flashing) digit can be changed by touching the UP and DOWN arrow buttons(2)..Otherdigitsmaybeselectedbytouching the LEFT and RIGHT arrow buttons (3)..
2.Once the interval has been entered, touch the SELECT button (4) to confirm the change..
3.If a service interval is active, the service alert display will be flashing.. Hold the START/STOP button (6) to clear the alert..
SERVICE | 1000 |
| PTO |
| 540 |
| MPH |
| km/h |
5 |
435/485/535