System Board Connectors, 158 | Dell DL2000 specs

Table 6-1. System Board Jumper Settings

Jumper SettingDescription

1 PWRD_EN

(default) The password feature is enabled.

The password feature is disabled.

2NVRAM_CLR (default) The configuration settings are retained at system boot.

The configuration settings are cleared at the next system boot. (If the configuration settings become corrupted to the point where the system will not boot, install the jumper and boot the system. Remove the jumper before restoring the configuration information.)

NOTE: For the full name of an abbreviation or acronym used in this table, see the "Glossary" on page 169.

System Board Connectors

See Figure 6-2 and Table 6-2 for the location and description of system board connectors.

158

Jumpers and Connectors

Image 158

Dell DL2000 owner manual System Board Connectors, 158, System Board Jumper Settings Jumper SettingDescription

Contents

Dell PowerVault DL2000 September Contents Memory Information Screen Responding to Error Messages Using the System Setup ProgramEntering the BMC Setup Module BMC Setup Module Options Integrated Devices Screen Serial Communication Screen Removing the Fan Bracket Replacing the Fan Bracket Installing a Sata Hard Drive Into a SataRemoving the Cooling Shroud Installing the Cooling Shroud Installing Memory Modules General Memory Module InstallationNon-Optimal Memory Configurations Memory Mirroring Support 108 Safety First-For You and Your System ContentsActivating the Integrated NIC TOE 105 110 Troubleshooting the Video Subsystem Troubleshooting IRQ Assignment ConflictsTroubleshooting External Connections Troubleshooting the Keyboard 157 Disabling a Forgotten Password 164153 157 Glossary Other Information You May Need About Your System Accessing System Features During Startup Ctrl+D Front-Panel Features and IndicatorsKeystrokes for Accessing System Features Description Ctrl+S Immediately after the power button is Power button System power is onBefore the power is turned off. If Using the end of a paper clip Hard-Drive Indicator Codes Hard-Drive Indicators Drive-status indicator green Amber Back-Panel Features and Indicators Seconds, and off six seconds Video connector Power Indicator CodesConnecting External Devices Dell remote access controller optional Power supply NIC Indicator CodesPower supply fault AC line status LCD Status Messages E1116 Temp Memory E1000Call Support E1114 Temp Ambient E12nn Xx PwrGd Redundancy E1310 RPM Fan ##E1313 Fan E1410 E1418 E1414Thermtrip Presence E1421 CPU Init E141F CPU ProtocolE1420 CPU Bus Perr E1422 CPU Machine E1624 E1620 PS # InputRange E1710 Channel PCI Serr Slot E1810 HDD ## FaultE1712 E1714 Unknown Err Abrt ConfigE1811 HDD ## Rbld E1812 HDD ## Controller E2017 Timer Fail E2011 Mem ConfigE2013 Shadow Bios E2018 Prog Timer E2021 Memory E2020 CPU ConfigE201E Population E2112 Mem Spare Crd Disable Crd #E2111 SBE Log # Dimm ## Solving Problems Described by LCD Status Messages Removing LCD Status Messages System Messages Update Remote Memory disabledConfiguration does Configuration Matched in size InstalledDimm pairs must be Speed, Installed in pairs Reset failedError Incorrect Diskette drive n Error Error MemoryRemote Access Has been disabled Membist failure Manufacturing modeDetected Following No timer tick No boot deviceNo boot sector on Been disabled by Error Embedded Width ErrorWidth Error Slot n Error Slot n PCI Bios failed to Seek error Read faultUpdate attempt Requested sector System memory has Setup programAmount Changed RAID error Timer chip counterCode update loaded Failed Unsupported CPU Write fault on Configuration isStarting in slot Write fault Current memory Diagnostics Messages Alert Messages Entering the System Setup Program Responding to Error Messages Main Screen System Setup OptionsUsing the System Setup Program Esc Main System Setup Program Screen Redirection after boot System Setup Program Options Description CPU InformationAllows the system to re-attempt the Boot Sequence after a Password on Memory Information Screen CPU Information Screen Integrated Devices Screen Default Take effect after the system reboots MAC Address Take effect after the system rebootsThis field does not have user-selectable settings Default Power Interface Acpi 3.0b specification Serial Communication Screen System Security Screen When set to On with Pre-boot Measurements, the system Password using the System Password option and cannot beDisabled at system start-up by pressing CtrlEnter Start-up Button is enabled in the System Setup program. When When set to Yes, all the contents of the TPM are clearedSystem, power is turned off immediately after the power Disabled, the button can only turn on system power Exit Screen System and Setup Password FeaturesUsing the System Password Assigning a System Password Type your password and press CtrlEnter Using Your System Password to Secure Your SystemType your password and press Enter Using the Setup Password Assigning a Setup Password Disabling a Forgotten Password Operating With a Setup Password Enabled BMC Setup Module Options Baseboard Management Controller ConfigurationEntering the BMC Setup Module Using the System Setup Program Installing System Components Recommended Tools Inside the System Installing System Components Inside the System Hot-pluggable fans SAS backplane Slimline optical drive Front BezelRemoving the Front Bezel Control panel Opening and Closing the System Replacing the Front Bezel Opening the System Closing the System Hard Drives Alignment J hooks Before You Begin Removing a Drive Blank Removing a Hot-Plug Hard Drive Installing a Drive BlankInstalling a Hot-Plug Hard Drive Replace the front bezel, if it was removed in step Removing a Hard Drive From a Hard-Drive Carrier Installing a Sata Hard Drive Into a Sata Drive CarrierReplacing a Hard-Drive Carrier Sata hard drive Installing System Components Hole labels Installing System Components Sata hard-drive Power Supplies Removing a Power Supply Replacing a Power Supply Power-supply handle System Fans Removing the Power Supply BlankInstalling the Power Supply Blank Removing a System Fan Replacing a Cooling Fan Fan Removing the Cooling Shroud Fan bracket Installing System ComponentsCooling Shroud Shroud pivots Cooling shroud Release latch Removing the Fan Bracket Installing the Cooling ShroudFan Brackets Replacing the Fan Bracket Tabs Cable Routing Removing the Cable Retention Bracket Installing the Cable Retention Bracket Chassis slots Tab Installing a SAS Controller Daughter Card SAS Controller Daughter Card Backplane Sasa and Sasb ConnectorsRelease tab Chassis slots Removing a SAS Controller Daughter Card Configuring the Boot DeviceSAS Controller Daughter Card Cabling Guidelines SAS controller SAS backplane a Inch x4 backplane Expansion Cards Expansion Card Installation GuidelinesInstalling an Expansion Card Installing System Components Card-edge connector Expansion card Removing an Expansion Card Expansion-Card Cage Removing the Expansion-Card Cage Lift the cage straight up to clear the chassis. See Figure Release latches Replacing the Expansion-Card Cage Installing the Drac Card and CablesDrac Card and Cables DRAC-card cables Retention standoff hole Drac card Filler plug Removing the Drac Card and Cables Optical Drive and Cable Removing the Optical Drive Installing the Optical Drive Optical -drive tray Optical drive 18. Sata Cable Routing in the PowerVault DL2000 System fans Installing the Optical Drive Cable Removing the Optical Drive Cable 100 General Memory Module Installation GuidelinesSystem Memory Memory Mirroring Support Non-Optimal Memory ConfigurationsMemory Sparing Support 101 Installing Memory Modules 102 19. Installing and Removing a Memory Module 103 Removing Memory Modules Removing a Processor Activating the Integrated NIC TOEProcessors 105 106 107 Retention lever latch ZIF socket Socket key Installing a ProcessorUnpack the new processor Close the processor shield. See Figure 109 System Battery Replacing the System Battery Negative side of battery connector 111 Expansion-Card Riser Boards Removing the Left Expansion-Card Riser Board Installing the Left Riser Board 113 Removing the Central Riser Board System board socket Installing the Central Riser Board115 Sideplane Board Removing the Sideplane Board 25. Sideplane Removal and Installation Sideplane board Guides Backplane connector Pins Installing System Components Removing the SAS Backplane Board Installing the Sideplane BoardSAS Backplane Board 119 Installing the SAS Backplane Board SAS backplane board Securing slots Securing tabs 121 Control Panel Assembly Service-only Procedure Removing the Control Panel Assembly Installing the Control Panel Assembly 123 System Board Service-only Procedure Removing the System Board 125 126 System board System-board securing tabs Installing the System Board 127 128 129 Safety First-For You and Your SystemStart-Up Routine 130 Troubleshooting IRQ Assignment ConflictsChecking the Equipment Monitor is not working properly Video memory is faulty Troubleshooting External ConnectionsTroubleshooting the Video Subsystem 131 Troubleshooting the Keyboard 133 Troubleshooting Basic I/O FunctionsTroubleshooting the Mouse Troubleshooting a Serial I/O Device Troubleshooting a USB Device 135 Troubleshooting a NIC NIC cannot communicate with network 137 Troubleshooting a Wet SystemLiquid spilled on the system Excessive humidity System was dropped or damaged Troubleshooting a Damaged SystemTroubleshooting the System Battery 139 Troubleshooting Power SuppliesAction Troubleshooting Your System Troubleshooting System Cooling Problems Troubleshooting a Fan 141 Troubleshooting System Memory Troubleshooting an Optical Drive 143 Troubleshooting an External Scsi Tape Drive Try using a different CD or DVD that you know works properly 145 Troubleshooting a Hard Drive Troubleshooting a SAS Controller Daughter Card 147 148 Troubleshooting Expansion Cards 149 Troubleshooting the Microprocessors 151 Troubleshooting Your System Using Server Administrator Diagnostics System Diagnostics Features System Diagnostics Testing Options When to Use the System DiagnosticsRunning the System Diagnostics As the system boots, press F10 during Post Selecting Diagnostics Options Using the Custom Test OptionsSelecting Devices for Testing 155 Viewing Information and Results System Board Jumpers Jumpers and Connectors System Board Jumpers 158 System Board ConnectorsSystem Board Jumper Settings Jumper SettingDescription Sata B connector Jumpers and Connectors ConnectorDell Remote Access Control Drac card 159 160 161 SAS Backplane Board ConnectorsDrive 0 SASDRV0 Tape drive power connector Drive 2 SASDRV2 Drive 3 SASDRV3 162 Sideplane Board ConnectorsExpansion-Card Riser-Board Components and PCI Buses Slot 3 PCIe x4 lane width Pin guide System board connector 163 Disabling a Forgotten Password 165 166 Getting Help Contacting Dell167 168 169 Amperes AC Alternating current 170 Celsius 171 ESD Electrostatic discharge Glossary 172 173 174 175 176 System diskette See bootable diskette Glossary 177 TCP/IP Transmission Control Protocol/Internet Protocol 178System memory See RAM 179 180 181 Index 182 183 Post 184 185 TOE 186 187 188