Appendix F Physical Block | Emerson Rosemount 8732 specs

Reference Manual

00809-0100-4665, Rev AA August 2010

Rosemount 8732

Appendix F

Physical Block

PHYSICAL BLOCK PARAMETER ATTRIBUTE DEFINITIONS

Table F-1. Physical Block Parameters

Physical Block Parameter Attribute Definitions . . . . . . . page F-1 I&M Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page F-4

The following table describes the parameters that are available in the physical block. Each line item in the table defines the element and specifies the requirements for each element. If a column is blank for a data element, it can be assumed that the column does not apply to that element.

Index	Parameter	Description
	Profibus PA Specific Block
	Header
16	BLOCK_OBJECT	This object contains the characteristics of the
		blocks.
17	ST_REV	The modification of at least one static
		parameter in a block has to be incremented
		by the according ST_REV at least by one.
18	TAG_DESC	Every block can be assigned a textual TAG
		description. The TAG_DESC must be
		unambiguous and unique in the fieldbus
		system.
19	STRATEGY	Grouping of Function Block. The STRATEGY
		field can be used to group blocks.
20	ALERT_KEY	This parameter contains the identification
		number of the plant unit. It helps to
		identify the location (plant unit) of an event.
21	TARGET_MODE	The TARGET_MODE parameter contains
		desired mode normally set by a control
		application or an operator. The modes are
		valid alternatively only, i.e. only one mode can
		be set at one time. A write access to this
		parameter with more then one mode is out of
		the range of the parameter and have to be
		refused.
22	MODE_BLK	This parameter contains the current mode,
		the permitted and normal mode of the block.
23	ALARM_SUM	This parameter contains the current states of
		the block alarms.
	Profibus PA specific Parameters
24	SOFTWARE_REVISION	Label of code in the device for tracking
		purpose.
		Please refer to D_8732EPA_SCMP.doc for
		details.
25	HARDWARE_REVISION	Mapped to HW_REV parameter in
		Manufacturing Block

www.rosemount.com

Image 153

Emerson Rosemount 8732 manual Appendix F Physical Block, Physical Block Parameter Attribute Definitions

Contents

Reference Manual RosemountPage North American Response Center Customer CentralPage Table of Contents Appendix D Appendix CAppendix E Appendix F System Description Section Introduction Service Support Safety Messages Explosions could result in death or serious injury Section Installation Mechanical Considerations Transmitter Symbols PRE-INSTALLATION Procedures Mount the Transmitter InstallationEnvironmental Considerations Pipe Mounting Jumpers/Switches HardwareConduit Ports and Connections Conduit Cables Electrical Considerations 1amp Power System Fuse Rating Manufacturer AC Neutral or DC Characteristic Ideal Specification Profibus PA Signal Connections Refer to -5 on Transmitter Wiring Connection Rosemount Transmitter Field Wiring Sensor Connections Rosemount Sensors Transmitter to Sensor Wiring Cable Shield Sensor Terminal Wiring Diagram Calibration Section ConfigurationQuick START-UP Sensor Calibration Number Assigning Device TAG and Node Address Basic Setup AI Block Absolute Parameter Description AI Block Parameter Attribute Definitions Reserved Hihilim Reserved Total Profibus PA specific Parameters Transducer Block Basic SetupPV Value PV Status Flow Units Options for Flow Rate Units Line Size Upper Range Value Lower Range Value Calibration Number Damping Basic Features Section OperationIntroduction Local Operator Interface Data Entry LOI LanguageLOI Menu Tree Class 2 Masters Diagnostics Basic Diagnostics Advanced Diagnostics Full Meter Verification RunTransmitter Only Sensor Only Coil Circuit Result Sensor Calibration ResultElectrode Circuit Result Sensor Signature No Flow Limit Set Pass/Fail CriteriaFlowing Limit Empty Pipe Limit Diagnostic Variables 8714i Results Electronics Trim Trims Master Reset Universal TrimAuto Zero Additional Parameters Advanced Configuration Detailed Setup Operating Mode Operation Signal ProcessingSP Control Number of Samples Device Info Construction Materials DSP Software RevFlange Type Flange Material Liner Material Electrode Material Process Leak Protection Optional Sensor Installation Explosions could result in death or serious injury Without Lifting Lugs Sensor Handling Upstream/Downstream Piping Sensor OrientationPipe Diameters Incline or Decline Orientation Electrode Plane Flow Direction Gaskets Installation Flanged SensorFlange Bolts Grounding Ring PTFE/ETFE liner Polyurethane liner Bolt PTFE/ETFE liner Size PN10 Code Gaskets Alignment and Bolting Code Line SizeNewton Installation, Studs Nominal Sensor Size Stud SpecificationsCentering Rings Nuts and Washers Size Code Line Size Pound-feet Newton-meter Installation Sanitary Sensor Grounding Options 14. Grounding with Grounding Rings or Lining Protectors 16. Grounding with Grounding Electrodes NPT Conduit Connection Standard Housing Configuration Process Leak Containment Relief Valves Grounding Electrode Port Safety Information Maintenance Troubleshooting Wiring for Remote Configurations Installation Check and GuideBefore You Begin Transmitter Sensor Potential Cause Corrective Action Message Potential Cause Corrective Action Message Transmitter Troubleshooting Symptom Potential Cause Corrective ActionAdvanced Troubleshooting on next Perform the auto zero function with full pipe and no flow Wiring Errors Process Noise Installed Sensor Tests Quick Troubleshooting Location Equipment Connections 00809-0100-4665, Rev AA August Sensor Test Sensor Circuit Diagram Uninstalled Sensor Tests Measuring at Connections N5, KD Hazardous Location CertificationsHazardous Location Certification Measuring at Connections N5, E5, CD Appendix a Reference Data Functional Specifications DC Load Limitations Analog Output DC Supply Current Requirements Switch-on current Power ConsumptionAmbient Temperature Limits Operating Storage Output Signals Series Advanced Diagnostics Capabilities Profibus PA Function Blocks Accuracy Performance SpecificationsRosemount E Series with 8705/8707 Sensor Rosemount E-Series with 8711 Sensor Rosemount E-Series with Legacy 8705/8707 Sensors Ambient Temperature EffectRosemount E-Series with Legacy 8711 Sensors Rosemount E-Series with Other Manufacturers’ Sensors Materials of Construction Physical Specifications Ordering Information IECEx Standard PlantWeb Product/Process Diagnostics StandardNepsi and CMC China Standard InMetro Brazil Standard Typical Model Number 8732E S T 1 a 1 N0 DA1 DA2 M4 Rosemount Product Certifications Appendix B Approval InformationEuropean Directive Information Type n protection type in accordance with EN50021 Canadian Standards Association CSA North American Certifications FM Approvals European Certifications Installation InstructionsSpecial conditions for safe use Kema 07ATEX0073 Special conditions for safe use International Certifications IECEx Special conditions for safe use KEMNepsi China InMetro Brazil Sensor ApprovalKosha Korea Rosemount Figure B-1. Atex Installation Drawings Figure B-2. Atex Installation Drawings Figure B-3. Atex Installation Drawings Figure B-4. Atex Installation Drawings Figure B-5. Atex Installation Drawings Figure B-6. Atex Installation Drawings Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Diagnostic Availability Appendix C DiagnosticsOptions for Accessing Diagnostics Diagnostics Mag User Practice 8732 Basic Licensing and Enabling Licensing the 8732 DiagnosticsTunable Empty Pipe Detection Tunable Empty Pipe Parameters Empty Pipe Trigger Level Optimizing Tunable Empty PipeEmpty Pipe Trigger Count Example GROUND/WIRING Fault Detection Troubleshooting Empty PipeGround/Wiring Fault Parameters Turning Ground/Wiring Fault On/Of Turning High Process Noise On/Off High Process Noise Detection Hz Signal to Noise Ratio Noise High Process Noise FunctionalitySpike Noise White Noise Initiating 8714i Meter Verification 8714I Meter VerificationEstablishing the baseline sensor signature All 8714i Meter Verification Test Parameters 8714i Meter Verification Test Results Parameters Viewing the 8714i Meter Verification ResultsTransmitter Calibration Verification Sensor Calibration Verification Optimizing the 8714i Meter VerificationCoil Circuit Verification Electrode Circuit Verification 8714i Meter Verification Functionality Troubleshooting 8714i Meter Verification TestSensor Signature Values Coil Circuit Resistance 8714i Meter Verification Measurements Rosemount Magnetic Flowmeter Calibration Verification Report Process leaks could result in death or serious injury Appendix D Digital Signal Processing Auto Zero Procedures How Does It Really Work? Flow RateTime When Should Signal Processing Be Used? Appendix E Universal Sensor Wiring Diagrams Rosemount Transmitter Sensor Manufacturer Number Generic Manufacturer WiringBrooks Endress and Hauser Rosemount Sensors Rosemount8705/8707/8711/8721 Sensors to Rosemount Transmitter To Rosemount 8732 Transmitter Rosemount Sensor TransmitterRosemount Rosemount 8701 Sensors Connecting Sensors of Other Manufacturers Model 5000 Sensor to Rosemount 8732 Transmitter Brooks SensorsBrooks Model Rosemount Trans MIT TER Model 7400 Sensor to Rosemount 8732 Transmitter Endress and Hauser Sensor to Rosemount Transmitter SensorsEndress and Hauser Sensors Model 10D1418 Sensor to Rosemount 8732 Transmitter Fischer and Porter SensorsRosemount 8732 Transmitter Coil Connections Model 10D1419 Sensor to Rosemount 8732 Transmitter Electrode Connections Model 10D1430 Sensor Remote to Rosemount 8732 Transmitter Model 10D1430 Sensor Integral to Rosemount 8732 Transmitter Rosemount Fischer and Porter Model 10D1465 Fischer and Porter Rosemount Sensors Transmitter Fischer and Porter Sensor to Rosemount 8732 TransmitterElectrodes Coils Fuse Rosemount Fischer and Porter Sensors Series 1800 Sensor to Rosemount 8732 Transmitter Foxboro SensorsFoxboro Series Rosemount Sensor Transmitter Rosemount Foxboro Series 1800 Sensors Series 1800 Version 2 Sensor to Rosemount 8732 Transmitter Foxboro Series Rosemount SensorVersion Transmitter Series 2800 Sensor to 8732 Transmitter Foxboro Rosemount Transmitter Sensor Veriflux VTC Sensor to 8732 Transmitter Kent Veriflux VTC SensorKent Veriflux VTC Rosemount Sensor Transmitter + 6 SCR Fuse Kent Sensor to Rosemount 8732 Transmitter Kent SensorsKent Sensors Rosemount Transmitter Coils Fuse Rosemount Kent Sensors Krohne Sensor to Rosemount 8732 Transmitter Krohne SensorsKrohne Rosemount Transmitter Sensors Coils Coil Shield Fuse Rosemount Krohne Sensors Series 1100 Sensor to Rosemount 8732 Transmitter Taylor SensorsTaylor Series Rosemount Sensor Transmitter Electrode Connections G 1 2 3 White Taylor Rosemount Sensors Transmitter Taylor Sensor to Rosemount 8732 Transmitter Yamatake Honeywell Sensors Yamatake Honeywell Sensor to Rosemount 8732 TransmitterYamatake Rosemount Honeywell Transmitter Sensors Yokogawa Sensors Yokogawa Sensor to Rosemount 8732 TransmitterYokogawa Rosemount Sensors Transmitter Generic Manufacturer Sensors Identify coil and electrode terminalsIdentify a chassis ground Physical Block Parameter Attribute Definitions Appendix F Physical Block Diagnosis Index Parameter Description Manufacturer Specific Parameters Condstatusdiag Parameter Name Initial Value Parameters Transducer Block Parameter Attribute Definitions Appendix G Transducer BlockIndex Parameter Name Description Information Measurementmode Eptrigcounts Meterveriftestcondout Fingerprintselect Rosemount Basic DP Slave Related Keywords Profibus DP Reaction Delay 20 6 bytes Standard Diagnostics +Max Output Len No. of TOT x 2 Bytes 2 * 3 TOT Max Data Len Slave Family Definition for Profibus PA Module Details Extended Diagnostic Bytes Manufacturer Specific Slot1 & Slot2 Configuration data Valid ConfigurationsDescription of the Module Assignment SlotDefinition Connections Orientation Test Index 00809-0100-4665, Rev AA August Piping Page Page Page Rosemount Divison Flow Pacific Private LimitedEmerson FZE