Emerson Rosemount 8732 specs

Rosemount 8732

Reference Manual

00809-0100-4665, Rev AA August 2010

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices. Please review the approvals section of the 8732 reference manual for any restrictions associated with a safe installation.

Electrical shock can result in death or serious injury

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause electrical shock.

The sensor liner is vulnerable to handling damage. Never place anything through the sensor for the purpose of lifting or gaining leverage. Liner damage can render the sensor useless.

To avoid possible damage to the sensor liner ends, do not use metallic or spiral-wound gaskets. If frequent removal is anticipated, take precautions to protect the liner ends. Short spool pieces attached to the sensor ends are often used for protection.

Correct flange bolt tightening is crucial for proper sensor operation and life. All bolts must be tightened in the proper sequence to the specified torque limits. Failure to observe these instructions could result in severe damage to the sensor lining and possible sensor replacement.

Emerson Process Management can supply lining protectors to prevent liner damage during removal, installation, and excessive bolt torquing.

5-2

Image 48

Emerson Rosemount 8732 manual Explosions could result in death or serious injury

Contents

Rosemount Reference ManualPage Customer Central North American Response CenterPage Table of Contents Appendix C Appendix DAppendix E Appendix F Section Introduction System Description Safety Messages Service Support Section Installation Explosions could result in death or serious injury Transmitter Symbols PRE-INSTALLATION Mechanical Considerations Installation Procedures Mount the TransmitterEnvironmental Considerations Pipe Mounting Jumpers/Switches HardwareConduit Ports and Connections Conduit Cables Electrical Considerations Power System Fuse Rating Manufacturer 1amp Characteristic Ideal Specification AC Neutral or DC Transmitter Wiring Connection Profibus PA Signal Connections Refer to -5 on Rosemount Transmitter Field Wiring Rosemount Sensors Transmitter to Sensor Wiring Sensor Connections Cable Shield Wiring Diagram Sensor Terminal Section Configuration CalibrationQuick START-UP Sensor Calibration Number Basic Setup AI Block Assigning Device TAG and Node Address AI Block Parameter Attribute Definitions Absolute Parameter Description Reserved Hihilim Reserved Profibus PA specific Parameters Total Basic Setup Transducer BlockPV Value PV Status Flow Units Line Size Options for Flow Rate Units Upper Range Value Lower Range Value Calibration Number Damping Basic Features Section OperationIntroduction Local Operator Interface Data Entry LOI LanguageLOI Menu Tree Diagnostics Class 2 Masters Basic Diagnostics Advanced Diagnostics Run Full Meter VerificationTransmitter Only Sensor Only Sensor Calibration Result Coil Circuit ResultElectrode Circuit Result Sensor Signature Set Pass/Fail Criteria No Flow LimitFlowing Limit Empty Pipe Limit Diagnostic Variables 8714i Results Trims Electronics Trim Master Reset Universal TrimAuto Zero Advanced Configuration Detailed Setup Additional Parameters Signal Processing Operating Mode OperationSP Control Number of Samples Device Info DSP Software Rev Construction MaterialsFlange Type Flange Material Electrode Material Liner Material Sensor Installation Process Leak Protection Optional Explosions could result in death or serious injury Sensor Handling Without Lifting Lugs Upstream/Downstream Piping Sensor OrientationPipe Diameters Incline or Decline Orientation Flow Direction Electrode Plane Installation Flanged Sensor GasketsFlange Bolts Grounding Ring PTFE/ETFE liner Polyurethane liner PTFE/ETFE liner Size PN10 Code Bolt Gaskets Alignment and Bolting Code Line SizeNewton Nominal Sensor Size Stud Specifications Installation, StudsCentering Rings Nuts and Washers Installation Sanitary Sensor Size Code Line Size Pound-feet Newton-meter Grounding Options 14. Grounding with Grounding Rings or Lining Protectors 16. Grounding with Grounding Electrodes Standard Housing Configuration NPT Conduit Connection Relief Valves Process Leak Containment Grounding Electrode Port Maintenance Troubleshooting Safety Information Installation Check and Guide Wiring for Remote ConfigurationsBefore You Begin Transmitter Sensor Potential Cause Corrective Action Message Message Potential Cause Corrective Action Transmitter Troubleshooting Symptom Potential Cause Corrective ActionAdvanced Troubleshooting on next Perform the auto zero function with full pipe and no flow Quick Troubleshooting Wiring Errors Process Noise Installed Sensor Tests 00809-0100-4665, Rev AA August Sensor Test Location Equipment Connections Uninstalled Sensor Tests Sensor Circuit Diagram Hazardous Location Certifications Measuring at Connections N5, KDHazardous Location Certification Measuring at Connections N5, E5, CD Functional Specifications Appendix a Reference Data DC Supply Current Requirements DC Load Limitations Analog Output Power Consumption Switch-on currentAmbient Temperature Limits Operating Storage Series Advanced Diagnostics Capabilities Output Signals Profibus PA Function Blocks Performance Specifications AccuracyRosemount E Series with 8705/8707 Sensor Rosemount E-Series with 8711 Sensor Ambient Temperature Effect Rosemount E-Series with Legacy 8705/8707 SensorsRosemount E-Series with Legacy 8711 Sensors Rosemount E-Series with Other Manufacturers’ Sensors Physical Specifications Materials of Construction Ordering Information PlantWeb Product/Process Diagnostics Standard IECEx StandardNepsi and CMC China Standard InMetro Brazil Standard Typical Model Number 8732E S T 1 a 1 N0 DA1 DA2 M4 Rosemount Appendix B Approval Information Product CertificationsEuropean Directive Information Type n protection type in accordance with EN50021 North American Certifications FM Approvals Canadian Standards Association CSA Installation Instructions European CertificationsSpecial conditions for safe use Kema 07ATEX0073 Special conditions for safe use International Certifications IECEx Special conditions for safe use KEMNepsi China Sensor Approval InMetro BrazilKosha Korea Rosemount Figure B-1. Atex Installation Drawings Figure B-2. Atex Installation Drawings Figure B-3. Atex Installation Drawings Figure B-4. Atex Installation Drawings Figure B-5. Atex Installation Drawings Figure B-6. Atex Installation Drawings Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Rosemount Appendix C Diagnostics Diagnostic AvailabilityOptions for Accessing Diagnostics Diagnostics Mag User Practice 8732 Basic Licensing the 8732 Diagnostics Licensing and EnablingTunable Empty Pipe Detection Tunable Empty Pipe Parameters Optimizing Tunable Empty Pipe Empty Pipe Trigger LevelEmpty Pipe Trigger Count Example Troubleshooting Empty Pipe GROUND/WIRING Fault DetectionGround/Wiring Fault Parameters Turning Ground/Wiring Fault On/Of High Process Noise Detection Turning High Process Noise On/Off Hz Signal to Noise Ratio High Process Noise Functionality NoiseSpike Noise White Noise 8714I Meter Verification Initiating 8714i Meter VerificationEstablishing the baseline sensor signature All 8714i Meter Verification Test Parameters 8714i Meter Verification Test Results Parameters Viewing the 8714i Meter Verification ResultsTransmitter Calibration Verification Optimizing the 8714i Meter Verification Sensor Calibration VerificationCoil Circuit Verification Electrode Circuit Verification Troubleshooting 8714i Meter Verification Test 8714i Meter Verification FunctionalitySensor Signature Values Coil Circuit Resistance 8714i Meter Verification Measurements Rosemount Magnetic Flowmeter Calibration Verification Report Appendix D Digital Signal Processing Process leaks could result in death or serious injury Procedures Auto Zero How Does It Really Work? Flow RateTime When Should Signal Processing Be Used? Appendix E Universal Sensor Wiring Diagrams Generic Manufacturer Wiring Rosemount Transmitter Sensor Manufacturer NumberBrooks Endress and Hauser Rosemount Sensors Rosemount8705/8707/8711/8721 Sensors to Rosemount Transmitter To Rosemount 8732 Transmitter Rosemount Sensor TransmitterRosemount Rosemount 8701 Sensors Connecting Sensors of Other Manufacturers Brooks Sensors Model 5000 Sensor to Rosemount 8732 TransmitterBrooks Model Rosemount Model 7400 Sensor to Rosemount 8732 Transmitter Trans MIT TER Sensors Endress and Hauser Sensor to Rosemount TransmitterEndress and Hauser Sensors Fischer and Porter Sensors Model 10D1418 Sensor to Rosemount 8732 TransmitterRosemount 8732 Transmitter Coil Connections Model 10D1419 Sensor to Rosemount 8732 Transmitter Model 10D1430 Sensor Remote to Rosemount 8732 Transmitter Electrode Connections Model 10D1430 Sensor Integral to Rosemount 8732 Transmitter Rosemount Fischer and Porter Model 10D1465 Fischer and Porter Sensor to Rosemount 8732 Transmitter Fischer and Porter Rosemount Sensors TransmitterElectrodes Coils Fuse Rosemount Fischer and Porter Sensors Foxboro Sensors Series 1800 Sensor to Rosemount 8732 TransmitterFoxboro Series Rosemount Sensor Transmitter Rosemount Foxboro Series 1800 Sensors Series 1800 Version 2 Sensor to Rosemount 8732 Transmitter Foxboro Series Rosemount SensorVersion Transmitter Series 2800 Sensor to 8732 Transmitter Foxboro Rosemount Transmitter Sensor Kent Veriflux VTC Sensor Veriflux VTC Sensor to 8732 TransmitterKent Veriflux VTC Rosemount Sensor Transmitter + 6 SCR Fuse Kent Sensors Kent Sensor to Rosemount 8732 TransmitterKent Sensors Rosemount Transmitter Coils Fuse Rosemount Kent Sensors Krohne Sensors Krohne Sensor to Rosemount 8732 TransmitterKrohne Rosemount Transmitter Sensors Coils Coil Shield Fuse Rosemount Krohne Sensors Taylor Sensors Series 1100 Sensor to Rosemount 8732 TransmitterTaylor Series Rosemount Sensor Transmitter Electrode Connections G 1 2 3 White Taylor Sensor to Rosemount 8732 Transmitter Taylor Rosemount Sensors Transmitter Yamatake Honeywell Sensors Yamatake Honeywell Sensor to Rosemount 8732 TransmitterYamatake Rosemount Honeywell Transmitter Sensors Yokogawa Sensors Yokogawa Sensor to Rosemount 8732 TransmitterYokogawa Rosemount Sensors Transmitter Generic Manufacturer Sensors Identify coil and electrode terminalsIdentify a chassis ground Appendix F Physical Block Physical Block Parameter Attribute Definitions Index Parameter Description Diagnosis Condstatusdiag Manufacturer Specific Parameters Parameters Parameter Name Initial Value Appendix G Transducer Block Transducer Block Parameter Attribute DefinitionsIndex Parameter Name Description Information Measurementmode Eptrigcounts Meterveriftestcondout Fingerprintselect Rosemount Profibus DP Basic DP Slave Related Keywords 20 6 bytes Standard Diagnostics + Reaction DelayMax Output Len No. of TOT x 2 Bytes 2 * 3 TOT Max Data Len Slave Family Definition for Profibus PA Extended Diagnostic Bytes Manufacturer Specific Module Details Valid Configurations Slot1 & Slot2 Configuration dataDescription of the Module Assignment SlotDefinition Index Connections Orientation Test 00809-0100-4665, Rev AA August Piping Page Page Page Rosemount Divison Flow Pacific Private LimitedEmerson FZE