Sample File modem_f.cfg

#

#COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F

#FUNCTIONS: Modem configuration file for many recent Hayes* compatible modems.

#This example uses the AT&F reset command to choose the factory defaults.

#This set up is preferred for modems with extended (&) commands. For early

#vintage modems, setup Z or Z0 is recommended. If your modem responds to

#the extended (&) commands and to factory default choices (&Fn), setup file

#F0 or F1 is recommended.

#

#* Trademark of Hayes Microcomputer Products, Inc.

#(C) COPYRIGHT International Business Machines Corp. 1996

#All Rights Reserved

#Licensed Materials - Property of IBM

#

#US Government Users Restricted Rights - Use, duplication or

#disclosure restricted by GSA ADP Schedule Contract with IBM Corp.

#If the modem has configuration switches, they should be set to the

#factory default settings.

ICDelay 1

 

 

 

DefaultTO 10

 

 

 

CallDelay 120

 

 

 

#

AT

Attention Code

,

Inserts delay in dialing commands

#

&F

Reset to default profile

Q0

Turn on responses

#

E0

Turn echo off

Q1

Turn off responses

#

V0

Use numeric responses

S0=0

Automatic answer inhibit

# +++

Escape to command mode

S0=2

Answer on second ring

#

H0

Hang-up

X0=0

Limit modem

response codes

#

 

 

T =

Tone mode.

When used as T\r, it is a

#

 

 

 

no op to maintain program synchronization

#

 

 

 

when modem may/will echo the commands.

#

 

 

 

 

 

# &C1

Detect CD

&D2

Respond to DTR (often the default)

#

 

 

 

 

 

#

%N

Call-Out phone number

%P

Paging phone number

#%S Modem speed (available to users)

#Following are common responses from a wide range of modems:

#16, 15, 12, 10, 5 and 1 are connection responses. Add others as required.

#7=busy; 6=no dial tone; 4=error; 3=no carrier; 2=ring; 0=OK

#

# PROGRAMMING NOTE: No blanks between double quote marks (").

condout:

send "AT&FQ0T\r"

# Reset to factory defaults.

 

ignore "0\r" or "OK\r\n" timeout 2

# Ignore modem response.

 

send "ATE0T\r"

# Initialize modem: Echo OFF,

 

expect "0\r" or "OK\r\n" timeout 2

#

Enable

responses (Numeric),

 

send "ATQ0V0X0T\r"

#

Limit response codes.

 

expect "0\r" timeout 2

# Confirm

commands successful.

 

send "ATS0=0\r"

# Set AutoAnswer OFF

 

expect "0\r" timeout 2

# Confirm

command successful.

 

send "AT&C1&D2\r"

# Detect carrier and DTR.

 

expect "0\r" timeout 2

# Confirm

command successful.

 

done

 

 

 

connect:

send "ATDT%N\r"

# Tone dialing command.

 

 

# %N from

Call Home setup.

# Expect a connection response.

expect "16\r" or "15\r" or "14\r" or "12\r" or "10\r" or "5\r" or "1\r" busy "7\r" timeout 60

Appendix F. Modem Configurations 199

Page 217
Image 217
IBM 6.00E+04, 6C4 manual Sample File modemf.cfg, # Componentname Espsetup Entry Service Processor Setup F