12.Select the sensitivity by moving the joystick upward or downward.
The sensitivity will be applied.
OFF: The motion detector is not activated on the camera channel.
LOW: The sensitivity level is low.
MID: The sensitivity is level is medium.
HIGH: The sensitivity level is high.
13.To exit the motion detection area setup window, press the CAM (SET) button.
The motion detection mode setup window will be dis- played on the monitor.
■VMD SEARCH
ANY AREA |
|
|
|
|
|
|
| |
MASKING DURATION |
|
|
| 24H | ||||
VECTOR |
|
|
|
|
|
|
| |
A | 20 s | B | 20 | s | C | 20 | s | D |
DURATION |
|
|
|
|
|
|
| |
A | 20 s | B | 20 | s | C | 20 | s | D 20 s |
|
|
|
| |||||
| SET : [SET] | SEARCH : [PLAY] | CANCEL : [ESC] | |||||
Notes:
•To cancel the motion detection area setup, press the MON (ESC) button. The VMD search list window will be displayed again on the monitor.
•Refer to the unit's operating instructions for details on each detection mode.
14.Select a desired detection mode with the 3D joystick, and select a desired parameter by performing either of the following.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
15.Press the CAM (SET) or PLAY/PAUSE button.
The motion detection mode will be determined, and the VMD search list window will be displayed again on the monitor.
Notes:
•Refer to Step 2 for the screenshot.
•To cancel the setting and return to the motion detection area setup window, press the MON (ESC) or EXIT button.
16.Select a desired recording event by performing one of the following.
•Move the 3D joystick controller up or down.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
Note: To move to the next or previous page, perform either of the following.
•Move the zoom wheel controller to the right or left.
•Rotate the shuttle ring clockwise or counterclock- wise.
17.Press the PLAY button.
The playback of selected recording event will start.
18.To exit the search mode, press the MON (ESC) or EXIT button.
The live image will be displayed again on the monitor.
• Marking search
The recording time of the recorded images with a marked point will be displayed in a list or a thumbnail. For playback, you will select the desired recording time to play. (Refer to the recorder's operating instructions for details on marking.)
1.Enter the recorder mode. (Refer to p. 19 Recorder Mode.)
2.Repeat pressing the SEARCH/T&D SEARCH button until the marking list window is displayed on the moni- tor.
The recorder will enter the searching mode.
TIME&DATE | CAM |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM | 01ch |
|
APR.25.03*12:34:56 AM APR.25.03*12:34:56 AM TOTAL | 12345 | |
TIME&DATE 
SEARCH 
REC EVENT 
SEARCH 
VMD 
SEARCH 
MARK
3.Select the desired marked time by performing one of the following.
•Move the 3D joystick controller up or down.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
Note: To move to the next or previous page, perform either of the following.
•Move the zoom wheel controller to the right or left.
•Rotate the shuttle ring clockwise or counterclock- wise.
4.Press the PLAY button.
The playback of selected recording event will start.
5.To exit the search mode, press the MON (ESC) or EXIT button.
The live image will be displayed again on the monitor.
•Thumbnail window
To change a list (recording event list, VMD search list, or marking search list) to the thumbnail, press the F1 button. The monitor display will become as follows.
27
