Mount locations for floor-fastening screws, Unit mm | Pioneer 502MX

Table-top Stand: PDK-5001

4.4.2 Mount locations for floor-fastening screws

* Secure the assembly to the floor using M6 screws at least 20 mm long.
558
152	533
108

292	130.7	179
	325
	656.6

30

4.4.3 Dimensions (* with Plasma Display Monitor PDP-502MX installed)

Unit: mm

1218

*765

714

*51	700

98*123

65

36

469

400

52

Image 52

Pioneer 502MX technical manual Mount locations for floor-fastening screws, Unit mm

Contents

Technical Manual Ver Table of Contents Table of Contents Features and Functions of the PDP-502MX Plasma Display Free choice of installation layout & slim designHigh definition, high contrast High quality, clear picture Features Specifications Specifications Video signals supported Input Response SignalsPC signals supported External Dimensions Rear View 22.5 11.1 146.6 Light Sensor for the Remote Main Unit Operation Panel48.1 29.8 21.4 Main Power Switch Section Controls and ConnectorsTerminal Section Sync Signal Impedance switch Main Power switch~ Control IN/OUT terminals RS 232C terminal Controls and Connectors Pin layout Combination IN/OUT terminal pin layoutGND DDC SDA Remote Control Unit Remote Control Unit Case Remote Control Unit Case Installation Site Requirements Safety Precautions Power requirements Temperature and humidity conditionsPrevent condensation Installation Conditions Heat dissipation Calculating heat quantity Product mounting holes Installation Conditions Mounting surface warping Installation Procedures Transportation precautionsUnpacking Ref. No Terms Installation Procedures Wiring How to unlock the speed clamp Fastening points for speed clamps Special Installation Mounting to fittings Operating environment for standard installationOperating environment for vertical installation Mounting to fittings Standard installation Example Vertical installation Example Special Instruction Hanging on the wall Requirements when used with PDP-S03-LR speaker systemHanging on the wall Special Installation Hanging on the wall Flush-wall installationWall-mounted installation Wall-embeddedinstallation Special Installation Embedding in the wall Operating Temperature RestrictionsTemperature in space X and Y Embedding in the wall 50mm 50mm Embedding in walls with no space provided behind the unit Special Installation Embedding in the wall Special installation When the display is put in a box When the display is put in a boxUsage temperature conditions BOX air temperature Ambient temperature 0 to 35 C Rear view the following area should be made of mesh Special Installation Ceiling suspension with wires Ceiling suspension with wiresAmbient temperature 0 to 40 C Make sure that this fan Is on the upper side Special Installation Ceiling suspension with wires Special Installation Hanging on the wall lengthwise Hanging on the wall lengthwise Special Installation Hanging from the wall lengthwise Temperature in space X and Y To 370 mm Page 100mm or more Page Horizontal connections Special installation Horizontal connectionsMm or more To 40C Partition Unit a Unit B Unit C Multiple Special installation Multiple50 to 300 mm or less To 35C Mm or more To 40C Standard Mounting Components Features and Characteristics ¶ Table-top Stand PDK-5001¶ PDP Bracket PDK-5005 ¶ Tiltable wall-mount Hardware PDK-5008 Precautions for installation contractors Handling precautionsHandling the Standard Mounting Components Installation of the Attachment Stand Dimensions Specifications Table-top Stand PDK-5001 Mount locations for floor-fastening screws Unit mm Assembly procedure Assembling ProcedureAssembling the stand Mounting procedures Mounting to the main unitAn Alternative Method Fastening to the floor Adjustable range of angles External Dimensions Plasma Ceiling Suspension Hardware one-side type PDK-5002 Assembling and installing the mounting software Preparations Used to hide holes in the ceiling Mounting the plasma display Page PDP Bracket PDK-5005 850 W × 130 D × 110 H mm External Dimensions Assembly Procedure Wrong An example of useAs the last step secure the M8 spring nuts h Package weight Dimensions of packagingTiltable Plasma Display Wall-Mount Hardware PDK-5006 External Dimensions Precautions before assembling Mount the horizontal frame to the vertical frames Mounting the monitor-fastening bolts to the plasma display Wall Side By tightening the screws a, as shown. This prevents Adjusting the angleLeft and right c screws Weight Carriable Stand PDK-5008Materials Finish 660 235 600 455 Mount the bracket support bolts on the support panel Mounting proceduresAlternately Shelf board viewed Adjusting the support casterFrom above External dimensions 74 W × 98 D × 714 H mm Speaker System PDP-S03-LR818 W × 315 D × 171 H mm Center of gravity Unit mm Installing procedure Installing the metal fixture on the speakerInstalling the speaker to the side of the plasma display Speaker System Cleaning the cabinet Connection with a stereo amplifier Speaker System R730 Mounting with PDK-5006 wall-mounting hardware Speaker System Speaker System Before Beginning Adjustments Operating modeNormal Operating Mode System has the following four major operating modes Adjustment mode is activated Input Video Signals Supported Lists of supported input signalsInputs 3 Input PC Signals Supported Table of PC Signal Responses Are for Apple About Screen Size Appearance of picture List of adjustable and settable items Normal Operating ModeHdtv system 50Hz system Menu Mode Step Integrator Mode GREEN/BLUE FAN Control AUTO/FIXEDMAX Aging Last MemoryMemory Timing Before Beginning Adjustments Normal Operating Mode About normal operating modeThis switches the input to the next input = Original = 4 3 Normal = Full = Zoom = Menu Mode About menu mode Example of menu mode operation Select Picture Menu Mode Step Step Make adjustmentsStep Complete the procedure Restores normal operating mode Settings in menu mode Setting power saveOFF Ô Mode PC OFF Setting the color system = set Color System 4.43 Ntsc Setting the three-dimensional Y/C separator Factory presetSelect Setup Screen Input Brightness of parts of the input signal with Setting High ContrastOFF When connecting PCs Setting up peripheral equipmentSetting PC Setting the input signal format = Signal RGB= Signal Component Input 3 RGB Input 4 RGB Setting the clamp position Input 4 Mode Intensity levels of input signals are faithfully reproduced ABL OFF ABL on V enhancement tuning Adjustment level range H. ENHANCE, V. Enhance ±32 Screen Video signal input Menu layers Each screen shows an example display PC signal inputDetails differ according to the selections Integrator Mode About the integrator mode Example of integrator mode operation Select the item to adjustStep Put the unit into standby, and do the following Integrator Mode Step Step To complete your adjustments, exit integrator ModeEntering normal operating Mode Adjustments and settings in the integrator mode Adjusting the Picture Adjusting the White Balance Position = H.POSITION = CLK Freq = H.POSITION = CLK Phase Adjusting the ScreenScreen Adjusting the side mask Setting the color mode Color mode with the SET buttonWhen you switch the Color MODE, all of the input Move the cursor to Color MODE, and select the desired Setting the mirror mode Setting the brightness enhancement at the screen center Illustration Setting OSD displaySelect Option Setting the baud rate Setting Full Mask Setting the cooling fan control formula Auto To dissipate heat through air conditioning etc Checking the inside temperatureChecking the accumulated on time Adjusting SUB Volume Push the SET button to return to screen Screen Use of SUB Volume Example Audio Input Initializing Adjustments ALL Default Option 1 all Option 2 all SUB Volume Menu modePower Save Setup all 126 127 128 129 Screen adjustment values area tables About the RS-232C adjustment mode RS-232C Adjustment ModeAJY Plasma Display InterfaceRXD TXD CTS RTS IDS ID SET ID assignmentAssigns IDs RS-232 Adjustment Mode List of RS-232C commands How to read this table Input using the appropriate input switching command IN1~4 Command Full Name Normal DirectName Validity About the GET commands Temperature C see note XXXTxD output value 3 bytes Outside air Connections for remote control signals are as shown below Combination ConnectionConnections Combination in terminal 139 How to switch KEY LOCK/UNLOCK Functions 141 Operating Precautions and recommendations Operating Precautions and recommendations Readjustment of White Balance Screen front protection panelVents Name Part Number