External Dimensions | Pioneer 502MX instruction

Tiltable Plasma Display Wall-Mount Hardware: PDK-5006

4.7.2 External Dimensions

389

124.6

38

32

20

6.6

1218

1194

1010

910

810

655

555

455

355

32

39.6

58935.8

714

400

(φ 23 x 35)
14-φ9 x 21	1162	1214
	14-φ9(φ 23)

4040

66

Image 66

Pioneer 502MX technical manual External Dimensions

Contents

Technical Manual Ver Table of Contents Table of Contents High definition, high contrast Features and Functions of the PDP-502MX Plasma DisplayFree choice of installation layout & slim design High quality, clear picture Features Specifications Specifications Input Response Signals Video signals supportedPC signals supported External Dimensions Rear View Light Sensor for the Remote Main Unit Operation Panel 22.5 11.1 146.648.1 29.8 21.4 Controls and Connectors Main Power Switch SectionTerminal Section ~ Control IN/OUT terminals Sync Signal Impedance switchMain Power switch RS 232C terminal GND Controls and Connectors Pin layoutCombination IN/OUT terminal pin layout DDC SDA Remote Control Unit Remote Control Unit Case Remote Control Unit Case Installation Site Requirements Safety Precautions Temperature and humidity conditions Power requirementsPrevent condensation Installation Conditions Heat dissipation Calculating heat quantity Product mounting holes Installation Conditions Mounting surface warping Unpacking Installation ProceduresTransportation precautions Ref. No Terms Installation Procedures Wiring How to unlock the speed clamp Fastening points for speed clamps Operating environment for vertical installation Special Installation Mounting to fittingsOperating environment for standard installation Mounting to fittings Standard installation Example Vertical installation Example Requirements when used with PDP-S03-LR speaker system Special Instruction Hanging on the wallHanging on the wall Wall-mounted installation Special Installation Hanging on the wallFlush-wall installation Wall-embeddedinstallation Temperature in space X and Y Special Installation Embedding in the wallOperating Temperature Restrictions Embedding in the wall 50mm 50mm Embedding in walls with no space provided behind the unit Special Installation Embedding in the wall Usage temperature conditions BOX air temperature Special installation When the display is put in a boxWhen the display is put in a box Ambient temperature 0 to 35 C Rear view the following area should be made of mesh Ambient temperature 0 to 40 C Special Installation Ceiling suspension with wiresCeiling suspension with wires Make sure that this fan Is on the upper side Special Installation Ceiling suspension with wires Special Installation Hanging on the wall lengthwise Hanging on the wall lengthwise Special Installation Hanging from the wall lengthwise Temperature in space X and Y To 370 mm Page 100mm or more Page Special installation Horizontal connections Horizontal connectionsMm or more To 40C Partition Unit a Unit B Unit C Special installation Multiple Multiple50 to 300 mm or less To 35C Mm or more To 40C ¶ PDP Bracket PDK-5005 Standard Mounting Components Features and Characteristics¶ Table-top Stand PDK-5001 ¶ Tiltable wall-mount Hardware PDK-5008 Handling precautions Precautions for installation contractorsHandling the Standard Mounting Components Installation of the Attachment Stand Dimensions Specifications Table-top Stand PDK-5001 Mount locations for floor-fastening screws Unit mm Assembling Procedure Assembly procedureAssembling the stand An Alternative Method Mounting proceduresMounting to the main unit Fastening to the floor Adjustable range of angles External Dimensions Plasma Ceiling Suspension Hardware one-side type PDK-5002 Assembling and installing the mounting software Preparations Used to hide holes in the ceiling Mounting the plasma display Page PDP Bracket PDK-5005 850 W × 130 D × 110 H mm External Dimensions Assembly Procedure An example of use WrongAs the last step secure the M8 spring nuts h Dimensions of packaging Package weightTiltable Plasma Display Wall-Mount Hardware PDK-5006 External Dimensions Precautions before assembling Mount the horizontal frame to the vertical frames Mounting the monitor-fastening bolts to the plasma display Wall Side Adjusting the angle By tightening the screws a, as shown. This preventsLeft and right c screws Materials WeightCarriable Stand PDK-5008 Finish 660 235 600 455 Mounting procedures Mount the bracket support bolts on the support panelAlternately Adjusting the support caster Shelf board viewedFrom above 818 W × 315 D × 171 H mm External dimensions 74 W × 98 D × 714 H mmSpeaker System PDP-S03-LR Center of gravity Unit mm Installing the speaker to the side of the plasma display Installing procedureInstalling the metal fixture on the speaker Speaker System Cleaning the cabinet Connection with a stereo amplifier Speaker System R730 Mounting with PDK-5006 wall-mounting hardware Speaker System Speaker System Normal Operating Mode Before Beginning AdjustmentsOperating mode System has the following four major operating modes Adjustment mode is activated Lists of supported input signals Input Video Signals SupportedInputs 3 Input PC Signals Supported Table of PC Signal Responses Are for Apple About Screen Size Appearance of picture Hdtv system List of adjustable and settable itemsNormal Operating Mode 50Hz system Menu Mode Step Integrator Mode GREEN/BLUE FAN Control AUTO/FIXEDMAX Last Memory AgingMemory Timing Before Beginning Adjustments This switches the input to the next input Normal Operating ModeAbout normal operating mode = Original = 4 3 Normal = Full = Zoom = Menu Mode About menu mode Example of menu mode operation Select Picture Step Complete the procedure Menu Mode StepStep Make adjustments Restores normal operating mode OFF Ô Mode Settings in menu modeSetting power save PC OFF Setting the color system = set Color System 4.43 Ntsc Select Setup Screen Setting the three-dimensional Y/C separatorFactory preset Input Setting High Contrast Brightness of parts of the input signal withOFF Setting up peripheral equipment When connecting PCsSetting PC = Signal Component Setting the input signal format= Signal RGB Input 3 RGB Input 4 RGB Setting the clamp position Input 4 Mode Intensity levels of input signals are faithfully reproduced ABL OFF ABL on V enhancement tuning Adjustment level range H. ENHANCE, V. Enhance ±32 Screen Video signal input Menu layers PC signal input Each screen shows an example displayDetails differ according to the selections Integrator Mode About the integrator mode Select the item to adjust Example of integrator mode operationStep Put the unit into standby, and do the following Entering normal operating Integrator Mode StepStep To complete your adjustments, exit integrator Mode Mode Adjustments and settings in the integrator mode Adjusting the Picture Adjusting the White Balance Adjusting the Screen Position = H.POSITION = CLK Freq = H.POSITION = CLK PhaseScreen Adjusting the side mask When you switch the Color MODE, all of the input Setting the color modeColor mode with the SET button Move the cursor to Color MODE, and select the desired Setting the mirror mode Setting the brightness enhancement at the screen center Setting OSD display IllustrationSelect Option Setting the baud rate Setting Full Mask Setting the cooling fan control formula Auto Checking the inside temperature To dissipate heat through air conditioning etcChecking the accumulated on time Adjusting SUB Volume Push the SET button to return to screen Screen Use of SUB Volume Example Audio Input Power Save Initializing Adjustments ALL DefaultOption 1 all Option 2 all SUB Volume Menu mode Setup all 126 127 128 129 Screen adjustment values area tables RS-232C Adjustment Mode About the RS-232C adjustment modeAJY Interface Plasma DisplayRXD TXD CTS RTS ID assignment IDS ID SETAssigns IDs RS-232 Adjustment Mode List of RS-232C commands How to read this table Command Full Name Normal Direct Input using the appropriate input switching command IN1~4Name Validity About the GET commands TxD output value 3 bytes Temperature C see noteXXX Outside air Connections Connections for remote control signals are as shown belowCombination Connection Combination in terminal 139 How to switch KEY LOCK/UNLOCK Functions 141 Operating Precautions and recommendations Operating Precautions and recommendations Vents Readjustment of White BalanceScreen front protection panel Name Part Number