Table-top Stand PDK-5001, Specifications | Pioneer 502MX instruction

Table-top Stand: PDK-5001

4.4 Table-top Stand: PDK-5001

4.4.1 Specifications

External dimensions	1218 (W) × 400 (D) × 765 (H) mm
Weight	4.0 kg (mounting hardware only)
	44.3 kg (mounting hardware and plasma display)
Materials	Base: plastic (ABS); Stand pipes: general structural steel tubes (STK-MR)
Finish	Finish: Base: paint (Pioneer original color); Stand pipes: semi-matt black paint
Package dimensions	726 (W) × 425 (D) × 100 (H) mm
Package weight	6.6 kg
Accessories
Base	× 1
Stand pipe, L	× 1
Stand pipe, R	× 1
Vertical pipe	× 1
Screw (4 × 12)	× 6
Bolt (M6 × 40)	× 2
Cap	× 2
Hexagonal wrench	× 1
Flat washer	× 4
Mount bolt (M8 × 300)	× 4
Turning-over protective bolt	× 2
Operating instructions	× 1

✩Operating Temperature Restrictions

•Ambient Temperature: 0 to 40 °C

✩Operating temperature restrictions for when the speaker system (PDP-S03-LR) is attached.

•Ambient temperature: 0 to 40 °C

✩Other factors

•Maintain sufficient clearance between the display and the wall (at least 100 mm)

51

Image 51

Pioneer 502MX technical manual Table-top Stand PDK-5001, Specifications

Contents

Technical Manual Ver Table of Contents Table of Contents High quality, clear picture Features and Functions of the PDP-502MX Plasma DisplayFree choice of installation layout & slim design High definition, high contrast Features Specifications Specifications Input Response Signals Video signals supportedPC signals supported Rear View External Dimensions Light Sensor for the Remote Main Unit Operation Panel 22.5 11.1 146.648.1 29.8 21.4 Controls and Connectors Main Power Switch SectionTerminal Section RS 232C terminal Sync Signal Impedance switchMain Power switch ~ Control IN/OUT terminals DDC SDA Controls and Connectors Pin layoutCombination IN/OUT terminal pin layout GND Remote Control Unit Remote Control Unit Case Remote Control Unit Case Safety Precautions Installation Site Requirements Temperature and humidity conditions Power requirementsPrevent condensation Heat dissipation Installation Conditions Product mounting holes Calculating heat quantity Installation Conditions Mounting surface warping Ref. No Terms Installation ProceduresTransportation precautions Unpacking Installation Procedures Wiring Fastening points for speed clamps How to unlock the speed clamp Mounting to fittings Special Installation Mounting to fittingsOperating environment for standard installation Operating environment for vertical installation Vertical installation Example Standard installation Example Requirements when used with PDP-S03-LR speaker system Special Instruction Hanging on the wallHanging on the wall Wall-embeddedinstallation Special Installation Hanging on the wallFlush-wall installation Wall-mounted installation Embedding in the wall Special Installation Embedding in the wallOperating Temperature Restrictions Temperature in space X and Y 50mm 50mm Embedding in walls with no space provided behind the unit Special Installation Embedding in the wall Ambient temperature 0 to 35 C Special installation When the display is put in a boxWhen the display is put in a box Usage temperature conditions BOX air temperature Rear view the following area should be made of mesh Make sure that this fan Is on the upper side Special Installation Ceiling suspension with wiresCeiling suspension with wires Ambient temperature 0 to 40 C Special Installation Ceiling suspension with wires Hanging on the wall lengthwise Special Installation Hanging on the wall lengthwise Special Installation Hanging from the wall lengthwise Temperature in space X and Y To 370 mm Page 100mm or more Page Special installation Horizontal connections Horizontal connectionsMm or more To 40C Partition Unit a Unit B Unit C Special installation Multiple Multiple50 to 300 mm or less To 35C Mm or more To 40C ¶ Tiltable wall-mount Hardware PDK-5008 Standard Mounting Components Features and Characteristics¶ Table-top Stand PDK-5001 ¶ PDP Bracket PDK-5005 Handling precautions Precautions for installation contractorsHandling the Standard Mounting Components Installation of the Attachment Stand Dimensions Table-top Stand PDK-5001 Specifications Unit mm Mount locations for floor-fastening screws Assembling Procedure Assembly procedureAssembling the stand Fastening to the floor Mounting proceduresMounting to the main unit An Alternative Method Adjustable range of angles Plasma Ceiling Suspension Hardware one-side type PDK-5002 External Dimensions Preparations Assembling and installing the mounting software Used to hide holes in the ceiling Mounting the plasma display Page 850 W × 130 D × 110 H mm PDP Bracket PDK-5005 External Dimensions Assembly Procedure An example of use WrongAs the last step secure the M8 spring nuts h Dimensions of packaging Package weightTiltable Plasma Display Wall-Mount Hardware PDK-5006 External Dimensions Mount the horizontal frame to the vertical frames Precautions before assembling Mounting the monitor-fastening bolts to the plasma display Wall Side Adjusting the angle By tightening the screws a, as shown. This preventsLeft and right c screws Finish WeightCarriable Stand PDK-5008 Materials 660 235 600 455 Mounting procedures Mount the bracket support bolts on the support panelAlternately Adjusting the support caster Shelf board viewedFrom above Center of gravity Unit mm External dimensions 74 W × 98 D × 714 H mmSpeaker System PDP-S03-LR 818 W × 315 D × 171 H mm Speaker System Installing procedureInstalling the metal fixture on the speaker Installing the speaker to the side of the plasma display Connection with a stereo amplifier Cleaning the cabinet Speaker System R730 Mounting with PDK-5006 wall-mounting hardware Speaker System Speaker System System has the following four major operating modes Before Beginning AdjustmentsOperating mode Normal Operating Mode Adjustment mode is activated Lists of supported input signals Input Video Signals SupportedInputs 3 Are for Apple Input PC Signals Supported Table of PC Signal Responses Appearance of picture About Screen Size 50Hz system List of adjustable and settable itemsNormal Operating Mode Hdtv system Step Menu Mode GREEN/BLUE FAN Control AUTO/FIXEDMAX Integrator Mode Last Memory AgingMemory Timing Before Beginning Adjustments = Original = 4 3 Normal = Full = Zoom = Normal Operating ModeAbout normal operating mode This switches the input to the next input About menu mode Menu Mode Select Picture Example of menu mode operation Restores normal operating mode Menu Mode StepStep Make adjustments Step Complete the procedure PC OFF Settings in menu modeSetting power save OFF Ô Mode = set Color System 4.43 Ntsc Setting the color system Input Setting the three-dimensional Y/C separatorFactory preset Select Setup Screen Setting High Contrast Brightness of parts of the input signal withOFF Setting up peripheral equipment When connecting PCsSetting PC Input 3 RGB Input 4 RGB Setting the input signal format= Signal RGB = Signal Component Input 4 Mode Setting the clamp position ABL OFF ABL on Intensity levels of input signals are faithfully reproduced Adjustment level range H. ENHANCE, V. Enhance ±32 Screen V enhancement tuning Menu layers Video signal input PC signal input Each screen shows an example displayDetails differ according to the selections About the integrator mode Integrator Mode Select the item to adjust Example of integrator mode operationStep Put the unit into standby, and do the following Mode Integrator Mode StepStep To complete your adjustments, exit integrator Mode Entering normal operating Adjusting the Picture Adjustments and settings in the integrator mode Adjusting the White Balance Adjusting the Screen Position = H.POSITION = CLK Freq = H.POSITION = CLK PhaseScreen Adjusting the side mask Move the cursor to Color MODE, and select the desired Setting the color modeColor mode with the SET button When you switch the Color MODE, all of the input Setting the mirror mode Setting the brightness enhancement at the screen center Setting OSD display IllustrationSelect Option Setting the baud rate Setting Full Mask Auto Setting the cooling fan control formula Checking the inside temperature To dissipate heat through air conditioning etcChecking the accumulated on time Push the SET button to return to screen Screen Adjusting SUB Volume Audio Input Use of SUB Volume Example Setup all Initializing Adjustments ALL DefaultOption 1 all Option 2 all SUB Volume Menu mode Power Save 126 127 128 129 Screen adjustment values area tables RS-232C Adjustment Mode About the RS-232C adjustment modeAJY Interface Plasma DisplayRXD TXD CTS RTS ID assignment IDS ID SETAssigns IDs List of RS-232C commands How to read this table RS-232 Adjustment Mode Command Full Name Normal Direct Input using the appropriate input switching command IN1~4Name Validity About the GET commands Outside air Temperature C see noteXXX TxD output value 3 bytes Combination in terminal Connections for remote control signals are as shown belowCombination Connection Connections 139 Functions How to switch KEY LOCK/UNLOCK 141 Operating Precautions and recommendations Operating Precautions and recommendations Name Part Number Readjustment of White BalanceScreen front protection panel Vents