System/Station Administration –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table 3 | Attribute Definitions (continued) | |
|
| |
Attribute | Description | |
Ringing Line | A user, by going | |
Preference |
| connected to the lowest line ringing in without having to press a CO line button or dial an |
|
| access button. |
|
|
|
Automatic |
| Automatic Preference via handset |
Preference |
| connection to lines or the intercom under various conditions. |
|
|
|
Hunt to |
| If a station is busy, Station Hunting enables the ringing of an alternate station as defined by |
Directory |
| the assignments in this program. If the |
Number [DN] | next | |
|
|
|
Standard |
| |
Telephone |
| call. |
|
| |
Hold/Park Recall | Each station can have a different time (from 011 to 160 seconds) from the point of placing | |
Time |
| a call on hold or park to the point of recall. |
|
|
|
MW Lamp |
| Turns on and off a message waiting LED for EKT and flash button. |
(Off = No Lamp, |
| |
On= With Lamp) |
| |
|
| |
LCD Personal | This option enables LCD digital and electronic telephones to store up to ten personal | |
Messages (10- | messages and offers the option of entering alphanumeric memos for each of the LCD’s | |
19) Allowed | Station Speed Dial numbers. | |
|
| |
Hold Display | Disables/enables the Hold Display Scroll feature independently for each telephone. When | |
Scroll |
| more than one call is on hold on a telephone, the Hold Display Scroll feature enables a |
(On=Enabled) | user to scroll through the held lines. | |
|
| |
Key | Determines whether or not a toll restricted telephone user is allowed to dial additional | |
After Answer | digits after answering an incoming CO line call. Initialized data sets both LEDs off for all | |
|
| telephone users. Both LEDs should be turned on for Toll Restricted telephones that must |
|
| answer incoming CO line calls and use speed dial buttons programmed to Hold or Park |
|
| calls and access the page system automatically. |
|
|
|
No CF/NA |
| A Handsfree Answerback call to an idle station in the Call Forward |
Handsfree |
| |
|
| the call from being forwarded 8 ~ 60 seconds after the called party has been talking in the |
|
| handsfree talk mode (handset |
|
| station continues to forward with this feature set. |
|
| |
DKT2000 Cont. | ||
DTMF Tones Off | their buttons (80 msec. minimum). This feature can be disabled with LED 17. If disabled, | |
|
| DTMF tones sent by these telephones are either 80 or 160 milliseconds, depending on the |
|
| selection made with Program |
|
| |
Automatic Hold | If this feature is allowed, station users with CO line buttons can place a CO line or intercom | |
|
| call on hold automatically by pressing another CO line button, or the DN/intercom button |
|
| and dialing the number. |
|
| |
Busy Station | Busy Station Ringing (BSR) and Busy Station Transfer (BST) operate together to ensure | |
Ringing/Busy | that a busy station always receives transferred line calls along with LED and tone | |
Station Transfer | indications. The station or Voice mail (VM)/auto attendant device that transfers the call | |
|
| must be programmed with BST (LED 20 ON) and the one that receives it must have BSR |
|
| (LED 19). |
|
|
|
Fixed Call |
| Fixed Call Forwarding is different from other station Call Forwarding options. It is fixed in |
Forward to |
| terms of the destination station number which is assigned in this program. The station user |
Station Port | cannot change the Fixed Call Forward destination, unlike the other station Call Forwarding | |
|
| options. |
|
| |
Ring Transfer | If a busy or ringing station does not answer a call sent to it via call transfer (CO line or over | |
| tie lines), the station originating the transfer is recalled after an amount of time determined | |
|
| with this program. |
|
|
|
52 | DKAdmin/DKBackup |