Advantech 5000 Series

Appendix F

Figure F-15 : Noise Reduction Techniques

F.4 Check Point List

• Follow the single point grounding rule?

• Normal mode and common mode voltage?

• Separate the DC and AC ground?

• Reject the noise factor?

• The shield is connected suitable?

• The diameter of wire thick enough?

• How about the sold erin g of conn ection?

• The terminal screw tightly?

ADAM-5000 F-15

Contents

Main A Message to the Customer.. Page Page Contents Page The ADAM-5000 series main systems DIP Switch Setting Modbus Commands for 5000 Series Modbus Address Mapping Address mapping of ADAM-5080 For ADAM-5000 ModBus Page Page Page Introduction 1.1 Overview I/O Module Software Utility Chapter 1 1.2 System Configuration Introduction 1.3 A Few Steps to a Successful System Step 2: Understand the System Kernel Step 3: Understand the I/O System Configurations Page 2.1 General Environmental Specifications Diagnostic Indicators Page Page Page Installation Guideline 2.2 Module Installation 2.4 Mounting DIN Rail Mounting 2-8 ADAM-5000 2.5 Wiring and Conections DC Power Supply Unit Wiring Installation Guideline Page Build-in Communication Ports for Diagnostic Connection (ADAM-5000E only) Chapter 2 Connection(ADAM-5000E only) Figure 2-9 Flexible Communication Port Function Connection Page ADAM-5000 System 3.1 Overview 3.2 Major Features of the ADAM-5000 System Chapter 3 Diagnosis ADAM-5000 System Chapter 3 (ADAM-5000E only) Flexible Communication Port(ADAM-5000E only) ADAM-5000 System Page Page Page Page Page Software Utilities 5.1 ADAM-4000 and ADAM-5000 Windows Utility Chapter 5 5.1.1 Overview Main Menu 5.1.2 Save Function Software Utilities Chapter 5 Timeout: 5.1.4 Search connected modules Chapter 5 5.1.5 Terminal Emulation Software Utilities 5.1.6 Data Scope Software Utilities 5.1.7 Saving modules Configuration to file 5.1.8 Load Modules Configuration File Page Software Utilities 5.1.9 Module Configuration Chapter 5 5.1.10 Module Calibration Zero Calibration: Software Utilities ADAM-5000 5-17 Page Page Chapter 5 5.1.12 Alarm Setting Digital Filter Software Utilities 5.1.13 Download Procedure Page Software Utilities Chapter 5 5.2 DLL (Dynamic Link Library) Driver 5.3 DDE (Dynamic Data Exchange) Server Page Page 6.1 Introduction 6.2 Syntax Page Page %aannccff Page $aaT $aa5 Command Set CPU Page Page $aaSiArrff Page $aaSi2 6.3 Analog Input Command Set Page Page Chapter 6 $aaSiB $aaSi6 Page $aaSiER Chapter 6 $aaSi1 $aaSi3 $aaSi9shhh $aaSi9shhhh Page Page Page Page Page Page #aaSiCj 6.7 Analog Input Alarm Command Set $aaSiCjAhs 5013/5017/5017H/5017UH/5018 Command Set Analog Input Alarm Page Page $aaSiCjArrff Page $aaSiCjB $aaSiCj(data) #aaSiCj(data) $aaSiCj4 $aaSiCj4 $aaSiCj0 $aaSiCj1 Page $aaSi6 Page $aaSiBB(data) Page Page Page Frequency Module Page Frequency Module Chapter 6 Frequency Module Frequency Module Page Page #aaSi $aaSi(data) Page Page $aaSiCj5 $aaSiCjG $aaSiCjG $aaSiCjAh $aaSiCAhCSkCh Page Page $aaSiCjRhU Page Page Troubleshooting 7.1 Hardware Diagnosis Chapter 7 7.3 System Indicators Faulty Power Supply Chapter 7 7.4 Communication Problems Troubleshooting 7.5 I/O Module Troubleshooting Page A.1 System Requirement to setup an ADAM-5000 System Page POWER SUPPLY +10~+30 VDC A.2 Basic Configuration Hook-up Page A.3 Baud Rate and Checksum Figure A-3 Grounding the INIT* terminal A.3 A Distributed ADAM-5000 Network System Hook-up Page B B.1 Analog Input Formats Engineering Units Appendix B ADAM-5000 B-5 ADAM-5000 B-7 Appendix B B.3.1 Analog Input Ranges - ADAM-5017UH B.4 Analog Ontput Formats Engineering Units B.5 Analog Ontput Ranges Page Page Appendix C C.1 Basic Network Layout RS-485 Network Appendix C Random RS-485 Network in a RS-498 Network C.2 Line Termination Page Page Appendix C C.3 RS-485 Data Flow Control Page Page How to Use the Checksum Feature Appendix D Example 2 How to Use the Checksum Feature Appendix E ADAM-4000/5000 System Grounding Installation refer to the following scheme: Page ADAM-4000/5000 System Grounding Installation Appendix F Grounding Reference Field Grounding and Shielding Application Overview EARTH as GROUND? Why we think the Appendix F 1.3The Frame Ground and Grounding Bar Appendix F Grounding Reference Single Point Grounding Those devices will Appendix F Single Point system. More cable, but more stable Page Page Page Grounding Reference F.3 Noise Reduction Techniques Page G Page G.2 Modbus Commands for 5000 Series Page Page Page Page ADAM-5000 I/O Modbus Mapping Table G.5 Address mapping of ADAM-5080 For ADAM-5000 ModBus z Slot Start Address :S(word) Nots: