Advantech 5000 Series

Grounding Reference

• Never stripping too long of the plastic cable cover. Otherwise, this

improper status will destroy the characteristic of the Shielded-

Twisted-Pair cable. Besides, those nude wires are easy to adhere the

noise.

• Cascade those shields together by “Soldering”. Please refer

to following page for further detail explanation.

• Connect the shield to Frame-Ground of DC power supply to

force those adhered noise flow to the ‘frame ground’ of the DC

power supply. (The ‘frame ground’ of the DC power supply

should be connected to the system ground)

Figure F-12 :The characteristic of the cable

• The characteristic of the cable

Don’t strip off too long of plastic cover for solderinF. Otherwise will

influence the characteristic of the Shielded-Twisted-Pair cable, and will

make an easy way to adhere noise.

F-12 ADAM-5000

Contents

Main A Message to the Customer.. Page Page Contents Page The ADAM-5000 series main systems DIP Switch Setting Modbus Commands for 5000 Series Modbus Address Mapping Address mapping of ADAM-5080 For ADAM-5000 ModBus Page Page Page Introduction 1.1 Overview I/O Module Software Utility Chapter 1 1.2 System Configuration Introduction 1.3 A Few Steps to a Successful System Step 2: Understand the System Kernel Step 3: Understand the I/O System Configurations Page 2.1 General Environmental Specifications Diagnostic Indicators Page Page Page Installation Guideline 2.2 Module Installation 2.4 Mounting DIN Rail Mounting 2-8 ADAM-5000 2.5 Wiring and Conections DC Power Supply Unit Wiring Installation Guideline Page Build-in Communication Ports for Diagnostic Connection (ADAM-5000E only) Chapter 2 Connection(ADAM-5000E only) Figure 2-9 Flexible Communication Port Function Connection Page ADAM-5000 System 3.1 Overview 3.2 Major Features of the ADAM-5000 System Chapter 3 Diagnosis ADAM-5000 System Chapter 3 (ADAM-5000E only) Flexible Communication Port(ADAM-5000E only) ADAM-5000 System Page Page Page Page Page Software Utilities 5.1 ADAM-4000 and ADAM-5000 Windows Utility Chapter 5 5.1.1 Overview Main Menu 5.1.2 Save Function Software Utilities Chapter 5 Timeout: 5.1.4 Search connected modules Chapter 5 5.1.5 Terminal Emulation Software Utilities 5.1.6 Data Scope Software Utilities 5.1.7 Saving modules Configuration to file 5.1.8 Load Modules Configuration File Page Software Utilities 5.1.9 Module Configuration Chapter 5 5.1.10 Module Calibration Zero Calibration: Software Utilities ADAM-5000 5-17 Page Page Chapter 5 5.1.12 Alarm Setting Digital Filter Software Utilities 5.1.13 Download Procedure Page Software Utilities Chapter 5 5.2 DLL (Dynamic Link Library) Driver 5.3 DDE (Dynamic Data Exchange) Server Page Page 6.1 Introduction 6.2 Syntax Page Page %aannccff Page $aaT $aa5 Command Set CPU Page Page $aaSiArrff Page $aaSi2 6.3 Analog Input Command Set Page Page Chapter 6 $aaSiB $aaSi6 Page $aaSiER Chapter 6 $aaSi1 $aaSi3 $aaSi9shhh $aaSi9shhhh Page Page Page Page Page Page #aaSiCj 6.7 Analog Input Alarm Command Set $aaSiCjAhs 5013/5017/5017H/5017UH/5018 Command Set Analog Input Alarm Page Page $aaSiCjArrff Page $aaSiCjB $aaSiCj(data) #aaSiCj(data) $aaSiCj4 $aaSiCj4 $aaSiCj0 $aaSiCj1 Page $aaSi6 Page $aaSiBB(data) Page Page Page Frequency Module Page Frequency Module Chapter 6 Frequency Module Frequency Module Page Page #aaSi $aaSi(data) Page Page $aaSiCj5 $aaSiCjG $aaSiCjG $aaSiCjAh $aaSiCAhCSkCh Page Page $aaSiCjRhU Page Page Troubleshooting 7.1 Hardware Diagnosis Chapter 7 7.3 System Indicators Faulty Power Supply Chapter 7 7.4 Communication Problems Troubleshooting 7.5 I/O Module Troubleshooting Page A.1 System Requirement to setup an ADAM-5000 System Page POWER SUPPLY +10~+30 VDC A.2 Basic Configuration Hook-up Page A.3 Baud Rate and Checksum Figure A-3 Grounding the INIT* terminal A.3 A Distributed ADAM-5000 Network System Hook-up Page B B.1 Analog Input Formats Engineering Units Appendix B ADAM-5000 B-5 ADAM-5000 B-7 Appendix B B.3.1 Analog Input Ranges - ADAM-5017UH B.4 Analog Ontput Formats Engineering Units B.5 Analog Ontput Ranges Page Page Appendix C C.1 Basic Network Layout RS-485 Network Appendix C Random RS-485 Network in a RS-498 Network C.2 Line Termination Page Page Appendix C C.3 RS-485 Data Flow Control Page Page How to Use the Checksum Feature Appendix D Example 2 How to Use the Checksum Feature Appendix E ADAM-4000/5000 System Grounding Installation refer to the following scheme: Page ADAM-4000/5000 System Grounding Installation Appendix F Grounding Reference Field Grounding and Shielding Application Overview EARTH as GROUND? Why we think the Appendix F 1.3The Frame Ground and Grounding Bar Appendix F Grounding Reference Single Point Grounding Those devices will Appendix F Single Point system. More cable, but more stable Page Page Page Grounding Reference F.3 Noise Reduction Techniques Page G Page G.2 Modbus Commands for 5000 Series Page Page Page Page ADAM-5000 I/O Modbus Mapping Table G.5 Address mapping of ADAM-5080 For ADAM-5000 ModBus z Slot Start Address :S(word) Nots: