|
| VR800 Owner’s Manual (MIDI Implementation Chart/MMC List) | |||
Data Type |
|
|
|
|
|
|
|
|
|
| |
<loop op . mode> | 12=stop |
| |||
| Indicates the next operating mode following locating to the start point (GP3) upon arriving |
| |||
| at the end point (GP6) by the play mode. In VR800, 12=stop only is effective. |
| |||
<post locate mode> | 12=stop |
|
| ||
| 15=play |
| |||
| Specifies operating mode in which VR800 should enter upon completing the locate |
| |||
| operation. Corresponds to the setting of AUTO PLAY ON ("15")/OFF ("12") on the main |
| |||
| unit. |
| |||
<count> | 01 ~ 7F |
|
| ||
| Specifies succeeding data byte numbers. |
| |||
<mmc track> | Complies to the MMC (MIDI Machine Control) standard track bit map. |
|
| ||
| In VR800, you always need to specify two byte combinations of "r0" and "r1." |
| |||
<edit message> | 00 = no message |
|
| ||
| 01 | = completed (completion flag) |
| ||
| 02 | = active (execution flag) |
| ||
| 02<mmc time> = Indicates unprocessed time by active (execution flag) and <mmc time>. |
| |||
| 02<count><mmc track> = Indicates source track by active (execution flag) and <mmc |
| |||
| track>. Used for clipboard play. |
| |||
| 03 | = cancel (execution stop) |
| ||
| 05 | = Indicates rehearsal (rehearsal mode of auto rec). Possible of undo. |
| ||
| 06 | = Indicates take (take mode of auto rec). Possible of undo. |
| ||
| 10 | = over value error |
| ||
| 10 | <mmc time> = Capacity shortage time is indicated by over value error (error by |
| ||
| capacity shortage) and <mmc time>. In copy paste, it indicates capacity shortage time |
| |||
| required for a minimum one time paste. |
| |||
| 11 | = Indicates in point error (incorrect in point). |
| ||
| 12 | = Indicates out point error (incorrect out point). |
| ||
| 14 | = Indicates void data (data necessary for paste does not exist). |
| ||
| 18 | = Indicates track select error (track necessary to execute copy/move or erase/cut is not |
| ||
| correctly setup). |
| |||
| 19<repeat count> = Indicates repeat number error and repeat numbers executable by |
| |||
| <repeat count>. |
| |||
| 1A = Indicates disable rec (record disable mode). |
| |||
| 25 | = Indicates can't undo rehearsal (rehearsal mode of auto rec). Impossible to undo. |
| ||
| 26 | = Indicates can't undo take (take mode of auto rec). Impossible toundo. |
| ||
| 71 | = Indicates on. |
| ||
| 72 | = Indicates off. |
| ||
<mmc time> | hr mn sc fr {ff/st} complies to the MMC standard time code. |
| |||
<on/off> | 70 = default |
|
| ||
| 71 | = on |
| ||
| 72 | = off |
| ||
<repeat count> | 01 ~ 7F |
| |||
| Especially when executing commands such as paste, the number of pasting times to be |
| |||
| continuously repeated following the auto punch in point is specified. |
| |||
<channel> | 00 ~ 08, 7F |
|
| ||
| Select recorder tracks 1~8. "00" in particular, is not specified (default setting). "7F" |
| |||
| indicates input/output of Adat optical. For details, refer to explanation on setting the |
| |||
| Command/Mode. |
| |||
<lock enable> | 00 = lock disable, chase disable |
|
| ||
| 01 | = lock enable, chase enable |
| ||
| Corresponds to SLAVE ON ("01")/OFF ("00") in the main unit. |
| |||
<lock status> | 00 = lock disable, chase disable |
|
| ||
| 01 | = lock enable (unlocked), chase enable (unlocked) |
| ||
| 11 | = lock enable (locked), chase enable (locked) |
| ||
<program> | 01 ~ 7F |
| |||
| Indicates program numbers (P1 ~ P99) on the main unit. However, VR800 can specify |
| |||
| only 01 (corresponds to P01) ~ 63H (corresponds to P99). |
| |||
<lock mode> | 40 = Free |
|
| ||
| 42 | = Vari |
| ||
| Indicates the slave mode when this equipment is set to slave ON. |
| |||
|
|
|
|
|
|
Page 111
Image 111
