VR800 Owner’s Manual (MIDI Implementation Chart/MMC List)
will be erased (data "0" is written in). However, when sound data length in the clipboard is less than 10ms, specifying the <repeat count> will be limited to "01."
Also, by specifying the <mmc track>, paste operation can be executed on other tracks in mono (one track unit) or stereo units (tracks
Since time corresponding to length of the move clipped sound data is required to complete the move paste operation, VR800 will immediately reply with "32 4E (<edit message=02 (ac- tive)>)" after receiving the command.
Following completion of the move paste operation, "32 4E (<edit message = 01 (completed)>)" will be sent.
If paste cannot be executed due to improper figures of the previously registered auto punch in point, insufficient disc ca- pacity, no sound data is in the clipboard, etc., the correspond- ing <edit message> will be replied.
13 42 (<channel><channel>): digital out ch.select command
The source channel for digital out is selected.
Normally, the first <channel> shown will be the SPDIF L chan- nel data, and the second <channel> the SPDIF R channel out- put. By
13 42 (<channel=7F><channel=0>): Adat out select command
In a device which can be switched between SPDIF and Adat, if the first display is <channel=7F>, then Adat Out can be setup.
13 43(<program>): program change command
The command for PROGRAM CHANGE of VR800. The present program number can be changed to the figure indicated by <program>.
12 4F (<channel><channel>): track exchange command (Ex- clusive command for
When the VR800 receives this command, the track can be ex- change between the specified <channel><channel>. Especially, if the first <channel=00><channel=01>, then exchange by grouping will be executed between channel
13 3E: product new program command (Exclusive command for
When the VR800 receives this command, a new program is compiled and the current program is transferred to the new program. As compilation of the new program is comparatively short time, it is replied with "33 3E (<edit message=01 (com- pleted)>)" immediately upon completion of execution.
If it cannot be executed for some reason, an error message will be sent back.
13 3F: delete current program command (Exclusive command for
When the VR800 receives this command, the current program is deleted and succeeding programs moved up and renumberd. If the deleted program is the only tune existing in the track, a new program will be made automatically.
As this delete current program is executed in a comparatively short time, "33 3F (<edit message=01 (completed)>)" will be sent back immediately upon completing the execution.
If it cannot be executed for some reason, an error message will be sent back.
13 41 (<channel><channel>): digital in ch.select command
The audio signal input from SPDIF digital in to assigned to the destination track specified by <channel>. The first <channel> shown in the command is the SPDIF L channel input, and the second <channel> the R channel input. "<channel=00>" indi- cates the adat input.
13 41 (<channel=7F><count><mmc track>): Adat in select com- mand
Channel = 7F indicates that it is Adat In. Normally, it will be "<count=0>" and all channels will be inputs from Adat In.
If <count=0><mmc track> is indicates, then only the tracks selected will be Adat In inputs.
13 44 (<on/off>): click on/off command
The command for setting the metronome on/off of VR800. When ON is set, the metronome signal will be fed to the track 8 output of VR800.
13 46 (<on/off>): Bar/Beat Resolution ON/OFF command
The command for ON/OFF of the bar/beat resolution function of this equipments' current program.
13 47 (<midi sync>): Midi Sync Out command
The setup command for MIDI Sync Out mode of this equip- ments' current program.
13 48 (<MTC offset mode>): MTC offset mode command
The setup command for MTC offset mode of this equipments' current program.
13 49 (<count=3> <on/off> <vari data>): Vari pitch command
13 49 (<count=1> <on/off>): Vari pitch command
The command for setting this equipments' vari pitch ON/OFF and pitch data.
Control of ON/OFF only is possible at <count=1> and both ON/ OFF and pitch data can be set at <count=3>.
14 01 (<signature map>): Signature set command
The command for setting the meter of this equipment. If a new data is registered at the bar position where a data exists, the former data will be written over. When this command is re- ceived, this equipment will reply with "34 01 (<edit message>)." Upon completing the registeration, <edit message> will reply with "01 (completed)," or with "10 (over value error)" if registeration is attempted at a
14 02 (<tempo set map>): Tempo set command
The command for tempo set of this equipment. If a new data is registered in a bar/meter where data already exists, the former data will be written over. When this command is received, this equipment will reply with "34 02 (<edit message>)." Upon completing the registeration, <edit message> will reply with "01 (completed)," or with "10 (over value error)" if registeration is attempted at a