VR800 Owner’s Manual (MIDI Implementation Chart/MMC List)

Explanation on the Command/Mode Set

12 22 (<on/off>): loop on/off command

The command for setting the "loop mode on/off" (=ON/OFF of AUTO RTN) of VR800. Default figure of the loop operation mode is "12=stop" and this cannot be changed.

12 28 (<post locate mode>): post locate command

The command for setting the "post locate mode" (=ON/OFF of AUTO PLAY) of VR800. It will stop after locating if "post locate mode=12." It will enter play after locating if "post locate mode=15."

12 2D (<on/off>): auto rec command

The command for setting "auto rec mode on/off" (=ON/OFF of AUTO PUNCH) of VR800. Upon receiving this command, VR800 will immediately reply the operating condition by sending "32 2D (<edit message>)".

12 41 (<lock enable>): lock enable command

The command for setting "slave mode on/off" (setup menu) of VR800.

12 42 (<lock mode>): lock mode command

The command for setup of the slave mode (setup menu) when this equipment is set to "slave mode on."

12 47 (<count><mmc track>): erase command

When this command is received, VR800 will erase the data (writes in "0" data) in the section from the pre-registered auto punch in point through auto punch out point in the track speci- fied by <mmc track>. Since time corresponding to length of the erase section is required to complete the erase operation, VR800 will immediately reply by "32 47 (<edit message=02 (active)>)" after receiving the command.

After the completion of erase operation, "32 47 (<edit mes- sage=01 (completed)>)" will be transmitted.

If erase cannot be executed due to improper figures of the pre- registered auto punch in point/auto punch out point, incor- rect track section, etc., the corresponding <edit message> will be replied.

12 49: clipboard play command

When this command is received, VR800 will playback once from the head of the sound data copied in the clipboard by the copy clip and move clip commands.

Immediately after receiving the command, VR800 will reply with "32 49 (<edit message=02 (active)><count><mmc track>)." The sound data track number is indicated by (mmc track>.

Upon completion of playback, "32 49 (<edit message=01 (com- pleted) is sent and clipboard play is ended. If there is no sound data in the clipboard, "32 49 (<edit message=14 (void data)>)" will be sent and clipboard play operation will be interrupted.

12 45 (<count><mmc track>) : copy clip command

When this command is received, VR800 will copy (multiple number of tracks can be copied simultaneously) the sound data, as data for copy paste, from the pre-registered clipboard- in point to the clipboard-out point in the track specified by <mmc track>. With completion of copying the data into the clipboard, VR800 will immediately reply with "32 45 (<edit message=01 (completed)>)". If copy cannot be executed due to improper figures of the pre-registered clipboard in/clipboard out points or incorrect track section, the corresponding <edit message> will be returned.

12 46 (<count=01><repeat count>): copy paste command

12 46 (<count><repeat count><mmc track>): copy paste com- mand

When this command is received, VR800 will paste the sound data which has been copied into the clipboard, on the same track from the pre-registered auto punch in point as the start- ing point for the number of time specified by <repeat count>. However, if the sound data length in the clipboard is less than 10ms, the specifying the <repeat count> will be limited to "01." Also, by specifying <mmc track>, paste can be executed on other tracks in mono (in one track units) or stereo units (in combinations of tracks 1-2, 3-4, 5-6, 7-8).

Since time corresponding to length of the copy clipped sound data is required to complete the copy paste operation, VR800 immediately replies with "32 46(<edit message=02 (active)>)" after receiving the command.

Successively upon completing the paste operation, "32 46 (<edit message=01(completed)>)" is transmitted.

If paste cannot be executed due to improper figures of the pre- registered auto punch in point, insufficient disc capacity, no sound data in the clipboard, etc., the corresponding <edit mes- sage> will be replied.

12 4A: undo command

Upon receiving this command, VR800 will revert to the condi- tion prior to editing copy paste,erase, move paste, cut, redo operation. With completion of undo operation, VR800 will reply with "32 4A (<edit message=01(completed)>)."

If VR800 is not possible to undo, "32 4A (<edit message=00 (no message)>)" will be replied.

12 4B: redo command

When this command is received, VR800 will return to the con- dition prior to undo operation.

With completion of redo operation, VR800 will reply with "32 4B (<edit message=01(completed)>)."

If VR800 is not possible to redo, "32 4B (<edit message=00 (no message)>)" will be replied.

12 4D (<count><mmc track>): move clip command

When this command is received, VR800 will copy (multiple tracks can be copied simultaneously) the sound data from the pre-registered clipboard in point to the clipboard out point, as data for move paste operation. With completion copying the data into the clipboard, VR800 will immediately reply with "32 4D (<edit message=01 (completed)>)." If copy cannot be ex- ecuted by the reason of pre-registered improper clipboard in/ clipboard out point figures or incorrect track section, etc., the corresponding <edit message> will be replied.

12 4E (<count=01><repeat count>): move paste command

12 4E (<count><repeat count><mmc track>): move paste com- mand

When this command is received, VR800 will paste the sound data which have been moveclipped in the clipboard, for the number of times specified by <repeat count> on the same track from the pre-registered auto punch in point as the starting point. At the same time, the move clipped original sound data

113

Page 113
Image 113
Fostex VR800 owner manual 113