![](/images/new-backgrounds/1280210/280210205x1.webp)
VR800 Owner’s Manual (Changing the initial setting: SETUP mode)
DIGITAL44.1kHz
SETUP
flashes
SYNC OUT |
| DRIVE |
CLK | SCSI | |
|
|
|
AUTO |
| A.PUNCH |
4.Press the HOLD/> key, the REWIND button, or the F FWD button to select a channel (L or r) and use the JOG dial to specify a track.
5.Press the EXECUTE/YES key.
The selected track assignment is stored, and [?] flashes.
Note: At setup of the digital output track, tracks to be assigned to L and R cannot be the same, for example, such as
To cancel the operation, or to restore the setting obtained prior to the EXECUTE/YES key press, press the STOP button or the EXIT/NO key. Each time you press one of these keys, the VR800 returns to the previous hierarchy level of the menu, and finally exits SETUP mode and displays the previous Time Base.
Setting BAR/BEAT resolution mode (“Resolu ?” menu)
The “Setting BAR/BEAT resolution mode” menu enables you to turn BAR/BEAT resolution mode on and off. The initial setting is “off.” When you turn this mode on, the CLK (clock) digits will be always round off to 00 and be stored in the memory key while the VR800 is using the BAR/BEAT/CLK Time Base. That is, beat resolution is used. Using this function allows you to automatically store a
For example, assume that you have stored the value for 001BAR1 46 CLK as the CLIPBOARD IN point, and the value for 002BAR 4
51 CLK as the CLIPBOARD OUT point.
These values will be used as they are if BAR/BEAT resolution mode is turned off. However, the mode is turned on, the following values will be stored instead. The following example has a time signature setting of 4/4.
001BAR1 46 CLK
00 CLK (A CLK value of 46 will be rounded off.)
002BAR4 51 CLK
00 CLK (A CLK value of 51 will be rounded up.)
• Initial setting | : [o FF] |
• Options | : [on] or [o FF] |
*This setting is shared by all Programs in the same disk.
*The settings cannot be saved and loaded as part of the song data.
*The settings are maintained after you turn off the power to the unit.
Setting BAR/BEAT resolution mode
1.While the VR800 is stopped, press the SETUP key to enter SETUP mode.
2.Turn the JOG dial to select [ Resolu ?] ([?]
flashes), then press the EXECUTE/YES key.
The current BAR/BEAT resolution mode setting appears on the display.
Pressing the EXECUTE/YES key turns off the flashing [?] character, and the BAR/BEAT resolution mode setting flashes. With the initial setting, [o FF] flashes as shown below.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 44.1kHz |
| ||
|
|
|
|
|
|
|
|
|
|
| DIGITAL |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| SETUP |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SYNC OUT |
| DRIVE |
| ||||
|
|
|
|
|
|
|
|
|
|
| CLK |
|
|
| SCSI |
| ||
|
|
|
|
|
|
|
|
|
|
| AUTO |
| A.PUNCH |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 44.1kHz |
| ||
|
|
|
|
|
|
|
|
|
|
| DIGITAL |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| SETUP |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SYNC OUT |
| DRIVE |
| ||||
|
|
|
|
|
|
|
|
|
|
| CLK |
|
|
| SCSI |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| AUTO |
| A.PUNCH |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
flashes
flashes