Fostex VR800 owner manual Load Err message, Unformat ! message, Action to take, Protected message

VR800 Owner’s Manual (Names and Functions)

Warning messages

The following warnings are shown operating mistakes are made, an unsuitable editing point (= locate point) is input, or when errors occur. If any of these warnings appear, refer to information detailed below.

			<Void Data> message
DIGITAL
			This means registered data
			necessary for the selected
SYNC OUT	DRIVE		operation is incorrect.
CLK		SCSI
AUTO	A.PUNCH

Action to take: Re-register the correct data.

			<Void Out !> message
DIGITAL
			This means the registered in/
			out point is wrong.
SYNC OUT	DRIVE
CLK		SCSI
AUTO	A.PUNCH

Action to take: Re-register the correct data.

			<Track Over> message
DIGITAL			This message appears when
			trying to record more than 2
			t r a c k s o f s i g n a l s
CLK		SCSI
SYNC OUT	DRIVE
			simultaneously using a MO
AUTO	A.PUNCH

drive/disk as a Current Drive.

Action to take: The MO drive only allows to record up to 2 tracks at a time. After changing the RECORD TRACK select key setting, please record signals.

					<Rec + Yes !> message
	DIGITAL
		SETUP			This is displayed when
SURE ?					formatting. This means press
	SYNC OUT		DRIVE		the EXECUTE/YES key while
	CLK			SCSI
	AUTO		A.PUNCH		pressing the RECORD button.

DIGITAL	44.1kHz	<Select Trk> message
		This means a track has not
		been specified.
SYNC OUT	DRIVE
CLK	SCSI
AUTO	A.PUNCH

Action to take: Select any one track with the RECORD TRACK select key.

			<Over !> message
DIGITAL
			This means there is
			insufficient disk space
			necessary for recording and
SYNC OUT	DRIVE
CLK		SCSI
AUTO	A.PUNCH		editing.

Action to take: Before proceeding to the next operation, temporarily data in order to source empty space necessary for the next operation.

			<Load Err > message
DIGITAL
			This means that loading is
			impossible because there is
			an error in data applied to
CLK		SCSI
SYNC OUT	DRIVE
AUTO	A.PUNCH		the DATA IN connector from
			the external DAT, or adat.

Action to take: Check the external DAT or adat connected to the DATA IN connector and be sure there is no problem with the DAT, or adat tape. Then, try loading again.

		<Unformat !> message
DIGITAL
		An unformatted or crashed
		SCSI disk. After a few
		seconds of this display, the
SYNC OUT	DRIVE
AUTO	A.PUNCH	VR800 automatically enters
		the SETUP mode [Format ?]
		menu.

Action to take: Press the EXECUTE/YES key while pressing the RECORD button.

Note: Any sound data recorded up to this point on the disk

will be lost.

Action to take:

Press the EXECUTE/YES key while pressing the RECORD button.

			<Protected> message
DIGITAL
			This means the disk inserted
			in the drive cannot be used
			because it is write-protected.
SYNC OUT	DRIVE
CLK		SCSI
AUTO	A.PUNCH		The disk will be ejected
			automatically.

Action to take:

Release the write-protect and re-insert it.

		<Acc Error> message
DIGITAL
		This message indicates that
		an error occurs when
		accessing the disk. With this
CLK	SCSI
SYNC OUT	DRIVE
		message, no keys and buttons
AUTO	A.PUNCH
		do not function at all.

Action to take: If this message appears, please use the following procedures.

1. Leave the disk inside the SCSI drive and turn off the power to the VR800 and all connected devices.

2. Turn on the power to the SCSI drive.

3. Make sure that the orange LED on the SCSI drive lights up in green and that the disk is not being accessed. Then, turn on the power to the VR800.

19