Hitachi SJ300 Series Terminal Listing, Code, Name, Page, Name, Page, Intelligent INPUTS, Intelligent OUTPUTS

4–10

Connecting to PLCs and Other Devices

	Terminal Listing			Use the following table to locate pages for intelligent input and output material in this chapter.
			Intelligent INPUTS					Intelligent OUTPUTS
	Symbol	Code		Name	Page	Symbol	Code	Name	Page
	RV	01	Reverse Run/Stop		4–12	RUN	00	Run signal	4–43
	CF1	02	Multi-speed select, Bit 0 (LSB)		4–13	FA1	01	Freq. arrival type 1 –	4–44
								constant speed
	CF2	03	Multi-speed select, Bit 1		4–13
	CF3	04	Multi-speed select, Bit 2		4–13	FA2	02	Freq. arrival type 2 –	4–44
								over-frequency
	CF4	05	Multi-speed select, Bit 3 (LSB)		4–13
	JG	06	Jogging		4–16	OL	03	Overload advance notice signal	4–46
	DB	07	External signal for DC injection		4–17	OD	04	Output deviation for PID control	4–47
			braking
						AL	05	Alarm signal	4–48
	SET	08	Set (select) second motor data		4–18	FA3	06	Freq. arrival type 3 – at freq.	4–44
	2CH	09	2-stage accel and decel		4–19	OTQ	07	Over-torque signal	4–50
	FRS	11	Free-run stop		4–20	IP	08	Instantaneous power failure signal	4–51
	EXT	12	External trip		4–21	UV	09	Under-voltage signal	4–51
	USP	13	Unattended start protection		4–22	TRQ	10	In torque limit signal	4–54
	CS	14	Commercial power source		4–23	RNT	11	Run time over	4–54
	SFT	15	Software lock		4–25	ONT	12	Power-ON time over	4–54
	AT	16	Analog input voltage/current sel.		4–26	THM	13	Thermal alarm signal	4–55
Operations Monitoringand
	SET3	17	Set (select) 3rd motor data		4–18	BRK	19	Brake release signal	4–58
	RS	18	Reset inverter		4–27	BER	20	Brake error signal	4–58
	STA	20	Start (3-wire interface)		4–29	ZS	21	Zero speed detect	4–58
	STP	21	Stop (3-wire interface)		4–29	DSE	22	Speed deviation maximum	4–58
	F/R	22	FW, RV (3-wire interface)		4–29	POK	23	Positioning completion	4–58
	PID	23	PID ON/OFF		4–30	FA4	24	Freq. arrival type 4 –	4–44
								over-frequency (2)
	PIDC	24	PID Reset		4–30
	CAS	26	Control gain setting		4–31	FA5	25	Freq. arrival type 5 –	4–44
								at frequency (2)
	UP	27	Remote control Up func.		4–33
	DWN	28	Remote control Down func.		4–33	OL2	26	Overload advance notice	4–46
								signal (2)
	UDC	29	Remote control data clearing		4–33
	OPE	31	Operator control		4–34
	SF1–7	32–38	Multi-speed bits 1 to 7		4–13
	OLR	39	Overload restriction		4–35
	TL	40	Torque limit enable		4–37
	TRQ1	41	Torque limit select, bit 1 (LSB)		4–37
	TRQ2	42	Torque limit select, bit 2 (MSB)		4–37
	PPI	43	P / PI mode selection		4–31
	BOK	44	Brake confirmation signal		4–39
	ORT	45	Orientation (home search)		4–41
	LAC	46	LAC: LAD cancel		4–41
	PCLR	47	Position deviation reset		4–41
	STAT	48	Pulse train position cmd enable		4–41