Step 5

Starting at the top of the following table, locate your symptom and perform the action listed in the Action column.

Symptom

 

 

 

 

 

 

 

 

Action

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

power

LED

does

not

come on,

or

comChecks onthe

power

 

cable

 

to

the

outlet.

 

Check

the

and

does

not

stay

on.

 

 

 

circuit

breakers

and

check

 

for

 

power

at

the

 

 

 

 

 

 

 

 

 

outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ensure that the room temperature

is

within

60

-

 

 

 

 

 

 

 

 

 

90°F.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If

you

 

do not find a problem,

 

record

error code

 

 

 

 

 

 

 

 

 

M0PS0000 and report the problem to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

service

organization.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The diagnostics are loaded and

there RecordwasNO error code

M0SPK001.

 

 

 

 

 

 

 

 

 

beep heard from the system unit during the IPL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

sequence.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The system stops with the Diagnostic OperatingGoto “Step 6” on page 168.

 

 

 

 

 

 

 

 

Instructions

displayed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

system

stops with

a

prompt to enterEntera the password.

You

are

not

allowed

to

 

password.

 

 

 

 

 

 

 

continue until a correct password has been

 

 

 

 

 

 

 

 

 

 

 

entered. When you have entered a valid

 

 

 

 

 

 

 

 

 

 

 

password, wait for one of the

 

other

conditions to

 

 

 

 

 

 

 

 

 

occur.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

system

stops with a three-, four-Record

the

error

code(s)

and

 

report

the

problem

eight-digit

error code(s)

displayed

onto thethe

service

organization.

 

 

 

 

 

 

 

 

console.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

system

login prompt

is

displayed.

You

may

 

not

have

pressed

the

correct

key

or

 

 

 

 

 

 

 

 

 

you

may

 

not

have

pressed

the

key

soon

enough

 

 

 

 

 

 

 

 

 

when

you

were

to

indicate

 

a Service

Mode

boot

 

 

 

 

 

 

 

 

 

of diagnostic programs. If this was the case,

 

 

 

 

 

 

 

 

 

start over at

the

beginning

of

 

this

step.

 

 

 

 

 

 

 

 

 

 

 

If

you

 

are

sure

that

you

pressed

the

correct key

 

 

 

 

 

 

 

 

 

in a

timely

manner,

go

to Step

7.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

system

does not

respond when the Go to "Step 7".

 

 

 

 

 

 

 

 

 

 

 

 

 

 

password

is

 

entered.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

166 RS/6000 Enterprise Server Model H80 Series User's Guide

Page 182
Image 182
IBM H80 Series manual Does Not Come on