Manuals / NEC / Cell Phone / Cell Phone

NEC NDA-24300 manual 17-C, CCH MB Key Turn on, ➀ Location of CCH/DCH card

Models: NDA-24300

1 653

Download 653 pages 50.84 Kb

Page 232

17-C

SYSTEM MESSAGES

CCH MB Key Turn ON

Default Alarm:	Default Grade:	Grade Modified:	Lamp Modified:
NON	3

This message displays when the MB switch on the CCH/DCH card is turned ON while extracting or inserting a circuit card or at PM initialization, etc.

1: XX00 0000 0000 0000 2: 0000 0000 0000 0000 3: 0000 0000 0000 0000

		➀
	4:	0000		0000		0000	0000		5:	0000	0000	0000	0000	6:	0000	0000	0000	0000
	7:	0000		0000		0000	0000		8:	0000	0000	0000	0000	9:	0000	0000	0000	0000

➀ Location of CCH/DCH card									b0-b4: Group No.
b7	b6	b5	b4		b3	b2	b1	b0	b5, b6: Unit No. (0-3)
b7	b6	b5	b4		b3	b2	b1	b0	b7: MG No.
									b7: MG No.

0/1 = Even-numbered MG/Odd-numbered MG

NDA-24300CHAPTER 3

Page 205

Issue 1

Image 232

NEC NDA-24300 manual 17-C, CCH MB Key Turn on, ➀ Location of CCH/DCH card

Contents

Issue NDA-24300Stock # October Liability Disclaimer NEAX2400 IPX Issue No 100 101 102 103 104 105 106 107 108 109 Issue No 251 Revision Sheet 5/9 403 479 555 Revision Sheet 9/9 System Operations and Maintenance Manual Table of Contents Table of Contents 116 LPM Accommodating UNIT/CIRCUIT Card Replacement Procedure Table of Contents Fault Repair Procedures NDA-24300TABLE of Contents Hard Time Clock Fault Routine Maintenance Procedure Chapter Maintenance Commands DTF101N List of Figures 301 List of Figures List of Figures NDA-24300LIST of Figures Page xiii Issue List of Tables List of Tables NDA-24300LIST of Tables Page xv Issue This page is for your notes General HOW to Follow this ManualNDA-24300CHAPTER When replacing a unit/circuit card with a spare When performing routine maintenanceIntroduction Chapter Administrative Management Procedures Purpose Summary of This Manual’s Contents Basic Knowledge System Configuration System Configuration 3shows the face layout of IMG0 IMG0 4shows the face layout of IMG1 IMG1 5shows the face layout of IMG 2/3 Line Equipment Numbers Lens Module Group Unit U2 U3 MG06 U0 U1 Group Group Number Allocations Level Total of eight Levels Lv0 Lv7 can be assigned on each Group Local Partition LP Number 11 LP Number Allocations System Messages System Message 3-E SUP Lock UP Failure Temporary NEC Tokyo Fault Detecting Function IOC CPU EMA 14 Fault Detection Block Diagram System Maintenance Outline Range of Faults Specification 15 General System Block Diagram 16 CPU Controlling Block Diagram IMG2 17 Speech Path Block Diagram IMG2 PIM 18 Speech Path Range of Fault Explanation of Terms Precaution about Diagnostic Procedure/Fault Repair Procedure Sense 0~F Kind of Restart Remarks 19 3M Model 8012 Portable Field Service Kit 21 How to Set the ROM in IC Socket 22 How to Clean the Connector Portion Start How to Follow Diagnostic Procedure/Fault Repair ProcedureEND System Maintenance Outline Judgment of fault status Reporting Fault to NEC Fault Reporting Method 16LCBE Forwarding Faulty Circuit Card Method This page is for your notes System Messages System Messages System Initialize Message no System Message Message no System Message Reset Interrupt Processing ➃ Data Load Result after restartB15 B11 Reference See , .2, for the repair procedure CPU Clock Down➁ Male-CPU Restart Information FF ➂ Related Call Information Level Infinite Loop SUP ➃ System Controlling Port B ➅ CPU Changeover Factors➆ System ALM ➇ Data Analyzed by NEC Engineers Memory Failure After detection of a clock fault➀ Information on Self-CPU Restart = CPU #0/CPU #1 B1-Level Infinite Loop Permanent ➂ B-level Infinite Loop B1-Level Infinite Loop Temporary ➀ ➁ ➂ Mate CPU Failure ➀ Mate-CPU Restart Information Abnormal Interrupt ➀ ➁ ➂ ➃ Both TSW Failure Permanent TSW Failure Permanent Both TSW Write Failure ➀ TSW system in which a fault isDetected B7 b6 TSW Write Failure ➂ Data Analyzed by NEC Engineers Both TSW Clock Failure ➀ TSW card in which a fault is➁ Clock status of No TSW TSW Clock Failure Both PLO Failure ➀ ➁ ➂ ➃ ➄ DCS Input Route Route Of Input Clock PLO Failure ➁ Valid Information bit for Scan Data System Messages Module Group Down Failure ➀ MG number of fault detection➁ Kind of failure TSW ACT Change Report NON ➂~➅ Status of ACT side TSW card ➆~➉ Status of ST-BY side TSW card ➂ Details on Switching Network ➀ System status of faulty Dlkc cardDlkc Data Transfer Failure Permanent Dlkc Data Transfer Failure Temporary PLO Restore Connected With Primary Oscillator M-OSC External Clock Level Infinite Loop Permanent ➀ Faulty Circuit Card MountingLocation Level Infinite Loop Temporary ➁ PM Restart Type Lock-Up Failure Permanent ➀ Faulty Circuit Card Location Lock-Up Failure Temporary ➀ Location of faulty PM Busy state and stops supplying power48V Over Current ➁ Location of faulty circuit card ➀ Location of faulty circuit cardGround Failure ➀ Location of PM Lens with a fault ➁ Kind of fault➂ Time Slot No. of fault This data is Valid only when the kind of fault is 08H Digital Line Failure ➂ ➃ ➂ ➃ This message displays when a digital line fault is restored Digital Line Restore➀ Location of faulty line Both TSW Ready Failure ➀ Unit and MG number of faultDetection Detection Reference See , .4, for the repair procedure TSW Ready Failure ➀ Details on faulty Dlkc card Dlkc Ready Failure ➀ Unit and MG number for MUX card with ready fault ➁ MG and system number for faulty MUX cardReference See , .3 and .4, for the repair procedure MUX Ready Failure ➀ Unit and MG number for MUX card with the ready fault Both MUX Ready Failure PCI Card Failure ➄ Error status on PCI slot PCI Card Failure Recovered ➀ Detection of PCI restoration ➄ Details on error restoration PCI Slot Reference See , , for the repair procedure System Failure➀ Probable cause for failure NON Fixed NON RGU & Howler Failure Line Load Control Start Line Load Control Stop When type of connection is Station connection Bad Call Notification➁ ➃ Station number see table b7 b6 b5 b4 b3 b2 b1 b0 ➄ The called station number ➄ Remote Route No When type of connection is Trunk connection➅ Remote Route No ➆ Called Trunk No ➇ Not used ➈ Time Slot Number of Link ➉ Not used When type of connection is ACD Trunk connection B4-b7 System Messages STA-Test Connection Data ➀ Test Item b0-b3 is valid only for Outgoing trunk test Error Numbers and Their Meanings Error no Meaning ➇ Tested Route No = SST, WT = SDT = TRG = Sdtt Emergency Call ➀ ➁ ➂ ➃ ➄ ➅➆ ➇ ➈ ➉ 11 ➀ Route Selection Time Pattern No Emergency Control StartAssigned at Attendant Desk Console Emergency Control Stop ➀ Suspension of Emergency Control When calling party is Station Abnormal Call Duration Data➀ Calling party information Calling station No. See table When calling party is ATTCON/DESKCON When calling party is TrunkRoute No. and Trunk No. See table ➃ Called party information ➄ Called Party Information Station to Station CallType of called party 00 = Station 01 = Attendant Console OG Call to outside IC Call from outside ➀ Detail Information B7 b6 b5 b4 b3 b2 b1 b0 Smdr Output Buffer Overflow AlarmFS = 0, FE = 0/1 ➂ Overflow Rate FS = 1, FE =➃ Overflow Rate FS = 2, FE = ➁ Smdr Group No➂ Port No FS = 3, FE = Smdr Output Buffer Overflow Release ➀ Detail Information System Initialize With Data Load ➁ Load Status System Messages System Initialize CPU MBR Key Turn on CPU MBR Key Turn OFF TSW MBR Key Turn on ➀ System status of TSW card TSW MBR Key Turn OFF TSW PLO Key Turn on Operation TSW PLO Key Turn OFF Almc MB Key Turn on ➀ Frame No. and its kind Almc MB Key Turn OFF ➀ Location of faulty Line/Trunk card b7 b6 b5 b4 b3 b2 b1 b0 PM MB Key Turn on PM MB Key Turn OFF ➁ Location of faulty PFT card NCU MB Key Turn on NCU MB Key Turn OFF Cyclic Diagnosis Normal ➀ Performed Diagnosis Item 00H Routine Diagnosis Start ➀ Performed Diagnosis Item➁ Pending Diagnosis Menu SYS1 Index 10H Program Memory Verification Normal End ➀ Routine Diagnosis➁ Information on HD ➂ Verification of Drive Number ➁ Verification of HD 20H Data Memory Verification Normal End➂ Verification of Data Memory ➁ Active TSW system after 30H TSW ACT/STBY Changeover Normal EndChangeover 40H CPU ACT/STBY Changeover Normal End ➁ MG and Unit of No. of Trunk 50H No Trunk Ineffective HoldIneffective Hold 70H Call Forwarding Memory Clear Normal End ➁ Information on Periodic Backup ➂ Backup Data to No system➃ Backup Data to No system A0H Periodic Back-up Normal C0H Detection of Remaining Link Normal End ➀ Detected Error Item B7 b6 b5 b4 b3 b2 b1 b0 Cyclic Diagnosis Information Error DetectedFor Release 4 or later Diagnosis ➁ Verification of HFD number 10H Program Memory Verification Discrepancy➃ Data analyzed by NEC Engineers 11H Program Memory Verification Impossible HFD Fault ➀ Error detection by Routine➃ Data analyzed by NEC Engineers ➄ Error Drive Diagnosis ➁ Verification Impossible of HD 12H Program Memory Verification Impossible Fault at CPU side 20H Data Memory Verification Discrepancy Diagnosis ➁ Verification of HFC 21H Data Memory Verification Impossible HFC Fault ➃ Error Type B7 b6 b5 b4 b3 b2 b1 b0Diagnosis ➁ HFC Impossible Verification ➄ Single Code ➅ Data analyzed by NEC Engineers ➆ Error Drive ➁ Active TSW No 30H TSW ACT/STBY Changeover Failure➂ -➅MUX card ACT-side linkage condition ➆ -➉MUX card Stby linkage condition B7 b6 b5 b4 b3 b2 b1 b0 31H TSW ACT/STBY Changeover Failure MUX Fault Detected Error ItemActive TSW No MUX card ACT-side linkage condition B7 b6 b5 b4 b3 b2 b1 b0 ➆ -➉MUX card Stby linkage condition B7 b6 b5 b4 b3 b2 b1 b0 41H CPU ACT/STBY Changeover Failure Diagnosis 42H CPU ACT/STBY Changeover Failure 43H CPU ACT/STBY Changeover Failure PCI Fault ➁ ACT system after changeover Diagnosis ➁ Lens of Trunk Ineffective Hold MG, U 50H Trunk Ineffective Hold Detected➂ Lens of Ineffective Hold Trunk G, LV ➄ ➅ ➆ ➇ ➈ 11➉12 51H Trunk Ineffective Hold Detected and Released 52H Trunk Ineffective Hold Detected Impossible 70H Call Forwarding Memory Clear NG Was stopped A0H Periodic Backup Abnormal End Error detection by RoutineDiagnosis Information of Periodic Backup Abnormal End Refer to No. ➂ Refer to No.➃ Refer to No.➄ ➁ ED Error Data C0H Detection of Remaining Link Abnormal End PLO MB Key Turn on PLO MB Key Turn OFF ➀ Location of faulty CCH/DCH card 13-A CCH Clock Failure 13-B CCH C-Level Infinite Loop Failure Permanent 13-C CCH C-Level Infinite Loop Failure Temporary 13-D CCH Lock-Up Failure Permanent 13-E CCH Lock-Up Failure Temporary 13-F CCH B-Level Infinite Loop Failure Permanent 13-G CCH B-Level Infinite Loop Failure Temporary CCS Link Failure Permanent 13-H➁ Data Analyzed by NEC Engineers Ccitt Factor Error ➂ Probable cause for failure 13-I CCS Link Failure Temporary FLT ID Ccitt Factor Error ➂ Probable cause for the failure 13-J ➁ CKT No. of faulty circuitRestoration From CCS Link Failure 13-K CCH Reset Interrupt Failure This message displays when a digital line failure occurs ➁ Kind of Fault B7b4 b3 b2 b1 b013-N ➀ Accommodated location B7 b6 b5 b4 b3 b2 b1 b0 13-O Digital Line Failure 13-P 13-Q DRU Battery Operation ➀ Accommodated location DRU Line Operation 13-R➀ Accommodated location 13-Z Power Failure ➀ MG No. and Unit No. of fault detection➁ Kind of Power ➂ Location of faulty circuit card This message displays when a VPS failure is detected 15-AVPS Failure Temporary ➁ Lens of VPS with the failure 15-B VPS Failure Permanent 15-C VPS Restore➀ Lens of VPS with the failure ➀ Intra-Office trunks that have 16-A Inside Trunk All BusyBecome all busy Trunk Name Route RouteTrunk Name 16-B Virtual Tie Line Set Report ➁ Virtual Tie Line Call HeaderAccommodated Location ➂ Virtual Tie Line Call Header Virtual Tie Line Cancel Report 16-C 16-E Virtual Tie Line Set Time Out ➀ Virtual Tie Line Call Header Call Source Reason Class Kind Data Reason Kind Value Invalid message class System Messages Reason Class Kind Data Reason Kind Value Sender Start Time Out 16-FCase of Station OG/ATT OG/ATT Tandem Connection ➅ Optn data ➄ Tenant No. of calling station Hex. b7 OP data 0/1➆ OG route number Hex B7 b6 b5 b4 b3 b2 b1 b0 ➇ Oprt data ➈ Trunk No. of OG trunk➉ Trunk No. of sender Number of digits dialed by caller Number dialed by caller See table B6 b5 b4 b3 b2 b1 Case of Tandem Connection➀ Type of connection ➁ IC route number Hex ➂ Oprt data ➇ Oprt data Number dialed by caller See table B7 b6 b5 b4 b3 b2 b1 b0 16-K Port Line OFF ➀ Faulty Port NoIOC0 IOC1 Port Line Restore 16-L 16-M Hard Clock Failure Hard Clock Restore 16-N ➁ Cause for fault This message displays when the IOC card fails16-T IOC Failure Temporary 16-U IOC Failure Permanent Error Code HEX Failure ➀ Error code16-X Station Exchanged Report ➁ Tenant No. of calling station B4-b7 B0-b3 17-A CCH MBR Key Turn on➀ Location of CCH/DCH card B7 b6 b5 b4 b3 b2 b1 b0 ➁ CKT No 17-B CCH MBR Key Turn OFF CCH MB Key Turn on 17-C➀ Location of CCH/DCH card 17-D CCH MB Key Turn OFF Day/Night Change Information 17-H➀ Tenant No B7 b6 b5 b4 b3 b2 b1 b0 ➁ Changing Method Night Mode 2 available only for Japan 17-O IOC MB Key Turn on 17-P IOC MB Key Turn OFF 17-Q IOC MBR Key Turn on 17-R IOC MBR Key Turn OFF DCH Back-Up Automatic Change Start/End 23-P➀ Condition of Dch System Messages 23-Q DCH Back-Up Manual Change Start/End System Messages MUX Clock Failure 23-Y➁ Scan Data ➀ MUX card location 23-Z Both MUX Clock Failure➂ Scan Data This message displays when the MAT is log-in or log-out 26-NMAT Log ➀ Port No. of the MAT logged in/out b0-b2 I/O Port No 26-R Call Trace When a call is originated from a station➃ User Group No. UGN Hex ➉ User Group No. UGN Hex Output Data Hex Actual Meaning Blank When a call is originated from a trunk Information on Called Party Informer Detailed meanings are as follows 26-V LAN Interface Error Report ➀ ➁ ➂ ➃ ➄ ➅ ➇➆ Error Code Output Data Definition Hex Details on Detected Error Kind of ErrorNot used When 9 =05 OAI / 07 MIS 12 ~ 24 Not used 26-W LAN Interface Release Report ➉ Device Number of recovered client PC Recovery Information When ➈=03 Smdr / 04 MCI➈ Application Type 33-A MUX Clock Restore ➁ RLS Data SDT Alarm Warning ➁ Details on alarm33-B ➀ MG Module Group Repair Procedure ➂ Alarm-detected HW=-/VC-11 Path Trouble SDT Alarm Trouble 33-C Repair Procedure NDA-24300CHAPTER 33-D SDT Alarm Restore ➁ Details on the fault SDT Interface Change Notify 33-E➁ Detailed information This page is for your notes Unit/Circuit Card Replacement Procedure LPM Accommodating Unit/Circuit Card Replacement ProcedurePrecaution Circuit Card Mounting Face Layout UNIT/CIRCUIT Card Replacement Procedure LANIPZ-PC19 GATEPZ-GT16 Operating Procedures UNIT/CIRCUIT Card Reference Item Remarks CPR Replacement Procedure PZ-IO27 Note How to Replace the CPU Circuit Card Accommodation into the New CPR Removal of Front Panel and Top Cover from CPR Isagt PZ-GT13 Lani PZ-PC19 Reattachment of CPR Top Cover and Front Panel Accommodation of New CPR into LPM By using the two screws, fasten the new HFD onto the CPR Insertion of New HFD into CPR Replacement Procedure Refer to -2for CPR face layout Refer to -3to replace the CPU Section Palm connector yet EMA SUP lamp on the EMA card goes OFF IMG0 lamp on the DSP flashes Top Cover Front Panel 10 Insertion of Isagt and Lani Cards 11 Reattachment of CPR Top Cover and Front Panel LPM CPR EMA Card Replacement Procedure 13 Insertion of New HFD Into CPR YES END Replacement Procedure IOC Card Replacement ProcedureOPE lamp on the IOC card goes UNIT/CIRCUIT Card Replacement Procedure Power Supply Unit Replacement Procedure CPU System Changeover Refer to .1.2 in Chapter UNIT/CIRCUIT Card Replacement Procedure Misc Card Replacement Procedure Keep MB switch UP Tswm Accommodating Circuit Card Replacement Procedure ALM RST button is used to reset the alarm lamps only Circuit Card Reference Item Remarks Function Name GT Card Replacement Procedure Misc BUS System changeover of GT from ACT to Stby mode GT Card Replacement ProcedureCPU OPE CPU DSP = OFF UNIT/CIRCUIT Card Replacement Procedure IMG0 CPU DSP = Flash green IMG1-3 CPU DSP = OFF TSW Card Replacement Procedure 16 System Block Diagram TSW and Other Speech Path Echelons TSW Card Replacement Procedure Use extreme care when operating the keys on the circuit card UNIT/CIRCUIT Card Replacement Procedure TSW ACT lamp on the new card goes OFF TSW ACT lamp on the new cardRemains OFF They are all steady-green Dlkc Card Replacement Procedure Refer to -16and Figure PLO Card Replacement Procedure OFF OPE lamp on the new card is OFF PWR SW Card Replacement Procedure Misc Card Replacement Procedure PIM Accommodating Circuit Card Replacement Procedure 18 Circuit Card Mounting Face Layout of PIM Circuit Card Reference Item Remarks Function Name 1 LC/TRK Circuit Card Replacement Procedure Keep MB switch set at UP MUX Card Replacement Procedure MUX ACT lamp on the new card is red Refer to -16and Figure SDT Card Replacement Procedure Procedure to Replace Optical Fiber Cable OPE lamp on the PA-SDTA card is steady-green Procedure to Replace PA-SDTA/PA-SDTB card UNIT/CIRCUIT Card Replacement Procedure OPE lamp on the new card is red Green PWR Card Replacement Procedure OPE lamp on the card goes OFF UNIT/CIRCUIT Card Replacement Procedure Fan Unit Replacement Replacement Procedure Fanu on Topu 20 Preparation for Fanu Replacement Fans on Topu 21 How to Replace Fanu Fans on Topu Replacement Procedure Fanu in Fan Box OFF 23 How to Replace Fanu Fans in Fan Box CPR Cooling Fan Replacement PZ-IO27 PZ-GT16 and PZ-GT13 Isagt 25 Extraction of CPR from LPM 27 How to Remove the Cooling FAN Fuse Replacement 28 Fuses Used by System 30 Fuse Locations Within System 31 Fuse Location Within Tswm 32 RGU Fuse Blown Fault Flowchart 33 DC -48V Fuse Blown Fault Flowchart Fault Repair Procedures Faulty Item Faulty Situation Reference Section Fault Repair Procedures Fan Unit Fault Line Fault Faulty Situation Reference Section Check Point Line Control Line Fault When Dial Tone DT Cannot Be Heard Check the faulty line on the MDF Line Fault When Dialing Results in Wrong Connection Line Fault When Bell Does Not Ring When Call Cannot Be Answered and Speech Cannot Be Made Dterm Fault END Trunk Fault Trunk Faulty Situation Reference Section Timings for Trunks Timings for Senders Trunk Control Controlling Trunk Circuit Cards and Speech Path Trunk ORT, SND, CFT Fault Trunk COT, TLT, DTI Fault Replace the Dterm with a spare TLT RA RB TA TB ATTCON/DESKCON Fault ATTCON/DESKCON Control ATT Connector Cabling and Connector Leads Accommodation ATTCON/DESKCON Fault Replace the ATTCON/DESKCON with a spare ATTCON/DESKCON Unit Fault Fault Situation Reference Section Unit Control Block Diagram Dual Configuration Unit Control Block Diagram Single Configuration Unit Fault Fault Related to Speech END For Single Configuration END Unit Fault When Dial Tone DT Cannot Be Heard Circuit card UP and extract For Single Configuration Circuit card UP and extract Start If the connection is set up, set Faulty system into StbyReplace the MUX circuit card with a Spare, and check it Speech Path TSW System Fault Faulty Situation Reference Section Speech Path Block Diagram IMG2 PIM Speech Path System Fault Fault Related to Speech TSW Write Failure For Dual Configuration END For Single Configuration END Speech Path System Fault When Dial Tone DT Cannot Be Heard Speech Path System Fault Stby Side Has Become Faulty END CPR TSW MUX Control System FaultEMA circuit cards CPU Controlling Block Diagram Lani Isagt Control System Fault Fault Occurs Intermittently END Control System Fault Stby Side Is Faulty 10 Alarm Bus Cable Connections Diagram IMG Alarm Indication Fault Fault of Alarm Indicating Panel 11 Cable Routing for Alarm Indications Fault That Cannot Be Detected Power Supply Fault System configuration System configuration 16shows the power supply system for PIM 18shows the power supply system for Tswm Fuse Blown Fault Circuit Breaker OFF Fault in PWR Supply Fault of Alarm Lamps on PWR Supply Fault Supervision FAN Unit Fault 19 Circuit Diagram of Fan Unit and Thermal Unit PIM Fan Unit FaultIf the voltage is -48 Tone Fault 20 Dial Tone Connection Tone Fault 21 External Hold Tone Supply Block Diagram System Down Fault 22 System Down Fault Repair Sequence When Cause for Fault Cannot Be Identified END When Faulty Circuit Cards Can Be Assumed From System Message Common Channel Interoffice Signaling Ccis Line Fault Ccis Line Control Specific CCH/CCT Card Is Faulty Check by replacing CCH/CCT card with a spare Fault of CCH, DTI and Related Flat Cable Integrated Service Digital Network Isdn Line Fault Isdn Line Control Specific DCH/PRT Card Is Faulty Check by replacing the DCH/PRT card with a spare Fault of DCH, DTI, and Related Flat Cable Hard Time Clock Fault Start END This page is for your notes Alarm Indications Kinds of Alarm Indications How to Stop Alarm Indications Alarm Indications on TopuLamp Color Function Contents System Operations Variable Alarm Indication Command Command Full NameCollection of System Messages Automatic Printout to System Message Dedicated Printer Recovery Procedure Display on MATIndication of Lockout Stations Indicating Method Rlst Operating Procedure Line Load Control Cancelling Line Load Control Operations on ATTCON-Cancelling Line Load Control Key Operations on DESKCON-Setting 11 Line Load Control Indication Deskcon Message Content IOC Line Monitor Make-Busy/Make-Busy Cancel of Station and Data Terminal Line Management Make-Busy/Make-Busy Cancel of C.O. Line/Tie Line Class Change and Number Change of Station and Data Terminal Line Management Commands Station Message Detail Recording System Smdr Transmission Data to Smdr Equipment Ascii Code Charac Binary Digit Remarks TER HEX 14 Message Format for Outgoing Call 15 Message Format for Incoming Call 16 Message Format for Station-to-Station Call For an Attendant Orig = 1 Data showing Attendant Number Data which indicates Call Start Time is as follows Call Start/Call End Time InformationData which indicates Call End Time is as follows Called Number Data which indicates the Called Number is as follows Data which indicates the Authorization Code is as follows Account Code/Authorization CodeData which indicates the Account Code is as follows Route Advance Information Condition B Information Call Metering Information Kind Contents Outgoing Incoming Text Format of Centralized Billing Fusion System Operations 17 Message Format for Outgoing Call Fusion 18 Message Format for Incoming Call Fusion 19 Message Format for Station-to-Station Call Fusion Data = 02 Calling Party Information Station Number ReferenceData = 08 Condition B Information FPC1 Data = 16 Automatic Number Indication Attcon Text Format of Smdr TCP/IP Interface Text sending direction Client Server Xxxxx Traffic Management Kind of Traffic Measurement5shows the kinds of traffic measurements Type Kind Description Measurement Deskcon Step Asyd Asydn Atrf Operating ProcedureAtrfn 21 IPX MAT Menu Display Image Example Full Command Name Data Output Details on DTFD/DTFDN CommandName Data collecting Log Tool Buttons Collect DataStop Print Log Save Text File Display AreaDown System Operations Office Data Stored Locations Office Data ManagementOffice Data Preservation Office Data Management Procedure 25 Office Data Change Procedure 26 Office Data Change Procedure 27 Backup Commands Data Management Commands Individual Speed Calling Data Hddmat commandOne-Touch Speed Call Memory Data Management Test Operations of Various Kinds Dcon Test Item Content of Confirmation Remarks Designated Connection Test Station Designated Connection Test Procedure Register Test Procedure Sender Test Procedure SRV=SSC, SID=17 Party Conference Trunk Test Procedure 31 3-Party Conference Test Procedure 32 3-Party Conference Test Connection Diagram Tone Test Procedure 33 Tone Test Procedure/Connection Diagram Tone no Kind of Tone Remarks Interrupt Ringing IR Test Procedure 34 Interrupt Ringing IR Test Procedure/Connection Diagram Trunk Test Procedure 35 Trunk Test Procedure 36 Trunk Test Connection Diagram Designated Connection Test DESKCON/ATTCON Trunk seizure by access code dialing Bad Call Notification Spdt Related System Data Routine DiagnosisASYD, SYS1, INDEX86 INDEX90 INDEX89INDEX304 HDD see Index Call Forwarding Data Clear See IndexRoutine Diagnosis Result System Control Procedures Belonging Isagt and LANI, are also changed over 37 Switching Network General Block Diagram Does not affect any other systems 38 How to Check LEDs and SW Keys for System Changeover IMG0 39 How to Check LEDs and SW Keys for System Changeover IMG1 IMG 2/3 41 How to Check Status LEDs How to Control CPU Block Type Operations Remarks 42 System Block Diagram Switching Network Between CPU and GT Manual System Changeover of CPU DSP Front View 45 CPU Changeover via MBR Key Forced Changeover of CPU LANIPZ-PC19 ISAGTPZ-GT13 How to Control Switching Block Changeover of Switching Block Type Operations Remarks Manual System Changeover of Speech Path System Dlkc PLO CPR Isagt CPU Lani Isagt PZ-GT13 Lani PZ-PC19 49 TSW/DLKC/MUX in ACT Mode 51 Speech Path System Changeover via Active GT MBR Key 53 Check of Active PLO 54 PLO in ACT/STBY Mode Manual System Changeover of PLO Flip the MB key on the PLO card. Refer to Figure 55 PLO Changeover via MB Key Initialization General CPU DSP#0 System Initialization by Turning on Power SupplyCPU DSP#1 IMG0 System Initialization by Key Operations on Topu Type Description 57 Conceptional Diagram of Initial Program Load 58 Related Keys and LEDs for System Initialization System Data KEY NON Load Program KEY NON LoadEND ON. on Line System Data KEY Load DSP of active CPU Is ON. on Line Program KEY Load Program KEY Load Active CPU light steadily green System Data KEY → NON Load System Initialization by Keys on CPU Front Panel Start EMA PH-PC40Check ACT0/ACT1 Lamps on the EMA System Initialization by Sinz Command Previous position after Return MB switch toMB lamp has turned on How to Turn ON/OFF Whole System How to Turn On Whole System How to Turn OFF Whole System 60 How To Turn OFF the Whole System Have already been installed in the HD. Office Data has not Been installedProcedure #2 see Table Office Data have been already installed in the HD ➀ When Power is OFF ➁ When Power is on OFF Line Set Sense switch at 1 DMLine On Line Set Sense switch at 2 DM Load Restart on the DSP of active CPU Set the Sense switch at DM Load Restart on the DSP On Line END This page is for your notes Routine Maintenance Procedure Flow of Procedures 1shows the tools and equipment required for test procedures Routine Maintenance ProcedureRequired Test Equipment and Tools Test EQUIPMENT/TOOLS Purpose Remarks Routine Maintenance Procedures Time Procedure Reference Section Remarks Ambient Conditions in Switch Room Check Alarm Check MAT/Printer Check Collection of System Messages Display of Locked-out Station Refer to , Fan Unit Fault, in Chapter Fan Unit Check Alarm Tests Main Power System Check Trunk RGU Check ATTCON/DESKCON Check Attendant Console Check Desk Console Check PM WED System Check Routine Maintenance Check Lists Condition And Cause Procedure and Parts Used Test Type Test Item Connection Diagram Connection test diagrammed toTrunk/Tie Line Right Connection Test-ATTCON/DESKCON ORT Function Perform the test by specifying Register/Sender Trunk RSTDP/PB RST FunctionTrunk no Sender SND0 Digital Conference Function Message displays as a result TestFunction Speech Release Remarks Trunk no Speech Path for Each PIM, and Ringing Generator Unit That the station rings Mounting Location CheckModule Name Unit Name PIM1 PIM2 PIM3 PIM4 Attendant Console ATTCON/DESKCON Test Item Connection DiagramDeskcon Attcon Call Termination Call OriginationSpeech Release Deskcon no Maintenance Commands Maintenance Commands Dteln Maintenance Commands Functional Outline Allc Assignment of Line Load ControlParameters Almg Assignment of Alarm Grade Data LMPGRD Type Atrf Assignment of Traffic Measurement Order Functional Outline Bosd Back Up One-Touch Speed Call Memory Data Cadsd Continuous Assignment of Station Data Example Input dataSTNEND=200 Result TEC =DP/PBRSC SFC When Delete is selected in the Type selection list box Carr Continuous Assignment of Alternative Route Restriction IC Lgrt IC Lgrt START/ENDOG Lgrt Catk Continuous Assignment of Trunk Data When Assign is selected in the Type/KIND selection list boxTKEND=21 Data Entry Result Tkstart When Delete is selected in the Type/KIND selection list boxTkend Details on Trunk Arrangement Type TYPE=1 Level → TYPE=3 Group → TYPE=5 Unit → Chapter Cbcn Control of Broadcasting for NDM FPCFPC of the designated Node Note Interval Broadcasting Interval Ccse Change of Common Signaling Channel Equipment CCH LensMG=XX, UNIT=X, GROUP=XX Link Cdbu Change of Dch Backup CNTSTS0 STS1 Cmod Change of System Mode Device=CPU =TSW System Cmwl Control Message Waiting Lamp UGN Cmwlt Control Message Waiting Lamps Telephone NumberTeln Cprs Controlled Alternate PRSCs Priority Restriction Class N/U=Normal =Urgent Cscl Continuous Change of Station Class Cstn Continuous Change of Station Number Dcbd Display of Call Block Entry Data NDA-24300CHAPTER Dcen Display of Connection Trunk Lens Data for LDM ClensCRT CTK Dcon Display of Connection Status LEN CRTConnection Route Number 1-1023 Note Connection Trunk Number 1-4095 Note Dftd Display of System Message Details Input data New/Old Show Details YES/NO Diss Display of Program Issue Version Issue Date Group 00-23 SP No Digits Ascii 2 digits Dlen Display of Lens Data Room Class ANX =Ground =UndergroundFLR Floor This command prints the Lens of stations in lockout state Dlsl Display of Lockout Station Lens Dlss Display of Lockout Station Number STN Lens Count Dlsst Display of Lock Out Station Number Telephone NumberTelephone Number max digits Dltel Display of Telephone Number from Lens for LDM Station Number Max digits Dntel Display of Telephone Number from Lens for NDM NIDNetwork ID Note Telephone Equipment Number Input Data Module Group MG number Dpkg Display of Setting Port PackageUnit U number Dpsw Display Package Switch Status KindPMN PKG Name Dstn Display of Station Data Dteln Display of Telephone Number Data for NDM Cpgn CpenShun Shcn DTF101 Display of Terminal Traffic Data DTF102 Display of Route Traffic Data DTF103 Display of Station Peg Count Data DTF104 Display of Attendant Peg Count Data DTF105 Display of Route Peg Count Data DTF201 Display of Service Peg Count Data DTF301 Display of UCD Route Peg Count Data DTF302 Display of UCD Group Peg Count Data DTF303 Display of Station Peg Count Data DTF501 Display of Attendant Answering Peg Count Data DTF601 Display of Connection Route Peg Count Data DTF602 Display of Connection Route Traffic Data DTF101N Display of Terminal Traffic Data for Fusion Network DTF102N Display of Route Traffic Data for Fusion Network DTF103N Display of Station Peg Count Data for Fusion Network Functional Outline DTF105N Display of Route Peg Count Data for Fusion Network DTF201N Display of Service Peg Count Data for Fusion Network Functional Outline Functional Outline Functional Outline Functional Outline Functional Outline Functional Outline Flinst File Install Data Install Procedure Input data System Select Hddfdd Data Control Between HDD and FDDHFD0/HFD1 File Name Select Auto Verify Afterward Hddmat Data Control Between HDD and MAT Hddmatn Data Control Between HDD and MAT for NDM Hdfp HDD Format of PBX Make Busy Information 0/1 Mbct Make Busy of Connection Trunk for LDM=Make Busy Outgoing Mble Make Busy of Lens =Make Busy Mbpm Make Busy of Port Microprocessor Input data MG Unit Group Display data =Make Idle =Make Busy Mbrt Make Busy of Route Mbrtlr Make Busy of Route-Logical Route Number LgrtMand as to the Internal route number and its meaning. Note Make Idle Mbsm Make Busy of System Message Printout Port no This command assigns the Idle/Busy status of stations Mbst Make Busy of Station Mbstt Make Busy of Station Telephone Number Exit Click to exit this commandMake Busy/Make Idle Display Data Mbtc Make Busy of Trunk-Continuous Mbtclr Make Busy of Trunk-Continuous-Logical Route Number Logical route number allocated to the Route Number. NoteTrunk Number Note =Make Busy Bothway Note This command assigns the Idle/Busy status of trunks Mbtk Make Busy of Trunk Mbtklr Make Busy Trunk-Logical Route Number Memhdd Data Control Between Memory and HDD Memhddn Data Control Between Memory and HDD for NDM Input data Direction Select MEM to HDD Fchn Mfch Make Busy of FcchFCH Number Pmbu Port Microprocessor Back Up Nating Port Microprocessor to MAT Ralm Release Alarm This command clears the fault indications Status Result of releasing the alarm Ralmn Release Alarm for NDMOK/NG =LENS Rlst Release Station/TrunkInformation Rlstt Release of Station/Trunk Telephone Number Telephone Number TrunkConnection Trunk External/Internal Route Number Trunk Number ERN GRNCSN/ZTN PCN Sinz System Initialization Kind of Initialization=System Initialize =System Initialize Office Data Load & System Initialize Spts Scanning of Port Status Type 1 By MG Type of Circuit Card Function Name Exit Type 2 By MG, Unit Port Status Report MG, Unit Display Type 3 By MG, Unit, Group Display of Scanning by Designating GroupIdle = Idle = Unassigned Port TCL Trunk Class Srts Scanning of Route Status Srtslr Scanning of Route Status-Logical Route Number Interval Interval Time of two scan Display DataRoute of Route Number Number of Idle/Busy TK Function Xhfd X-RAY HD or FDD DiagnosisArea Fault Sector Fault DriveMessage