Fan Unit Replacement | NEC NDA-24300 specs

UNIT/CIRCUIT CARD REPLACEMENT PROCEDURE

4.Fan Unit Replacement

This section explains how to replace the Fan Unit (FANU), which is fastened on the TOPU or inside the ded- icated fan box within the system. Because the fan is a vital device to protect the system from heated air, it is recommended that the fan (a total of three per unit) be replaced at least every two years to guarantee its high performance.

The mounting location of FANU differs, depending on the module configuration of each cabinet. When the system consists of a total of three modules or less, the FANU is mounted on the TOPU of the cabinet. Other- wise, the FANU is housed in the dedicated fan box in the center of the cabinet. Refer to Figure 4-19.

NEC	NEAX 2400 IMX

TOPU

TOPU

NEC	NEAX 2400 IMX

FAN BOX

FANU is located here.

FRONT VIEW

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

When FANU is mounted on TOPU

When FANU is mounted in FAN BOX

Figure 4-19 FANU Locations

Replacement Procedure: FANU on TOPU

When the FANU is mounted on the TOPU, perform the following replacement procedure:

STEP 1 Using a Phillips screwdriver, remove the four screws. Lift away the top cover.

STEP 2 Turn OFF the PWR SW on the PZ-M369. (Refer to Figure 4-20.)

STEP 3 Remove the fan fuse (5A) on the PZ-M369.

STEP 4 Remove the fan cables from the fan connector and the connector(s) corresponding to the fan to be replaced (for example, when replacing FAN #0, disconnect the FC0 connector together with the fan connector).

CHAPTER 4

NDA-24300

Page 296

Issue 1

Image 323

NEC NDA-24300 manual Fan Unit Replacement, Replacement Procedure Fanu on Topu

Contents

October IssueNDA-24300 Stock # Liability Disclaimer NEAX2400 IPX Issue No 100 101 102 103 104 105 106 107 108 109 Issue No 251 Revision Sheet 5/9 403 479 555 Revision Sheet 9/9 Table of Contents System Operations and Maintenance Manual Table of Contents 116 Table of Contents LPM Accommodating UNIT/CIRCUIT Card Replacement Procedure NDA-24300TABLE of Contents Fault Repair Procedures Hard Time Clock Fault Routine Maintenance Procedure Chapter Maintenance Commands DTF101N List of Figures 301 List of Figures List of Figures NDA-24300LIST of Figures Page xiii Issue List of Tables List of Tables NDA-24300LIST of Tables Page xv Issue This page is for your notes NDA-24300CHAPTER HOW to Follow this ManualGeneral Chapter When replacing a unit/circuit card with a spareWhen performing routine maintenance Introduction Purpose Administrative Management Procedures Basic Knowledge Summary of This Manual’s Contents System Configuration System Configuration IMG0 3shows the face layout of IMG0 IMG1 4shows the face layout of IMG1 5shows the face layout of IMG 2/3 Module Group Line Equipment Numbers Lens U2 U3 MG06 U0 U1 Unit Group Number Allocations Group Total of eight Levels Lv0 Lv7 can be assigned on each Group Level 11 LP Number Allocations Local Partition LP Number System Message 3-E SUP Lock UP Failure Temporary NEC Tokyo System Messages IOC CPU EMA Fault Detecting Function 14 Fault Detection Block Diagram System Maintenance Outline Range of Faults Specification 15 General System Block Diagram 16 CPU Controlling Block Diagram IMG2 17 Speech Path Block Diagram IMG2 PIM 18 Speech Path Range of Fault Explanation of Terms Sense 0~F Kind of Restart Remarks Precaution about Diagnostic Procedure/Fault Repair Procedure 19 3M Model 8012 Portable Field Service Kit 21 How to Set the ROM in IC Socket 22 How to Clean the Connector Portion END How to Follow Diagnostic Procedure/Fault Repair ProcedureStart System Maintenance Outline Judgment of fault status Fault Reporting Method Reporting Fault to NEC 16LCBE Forwarding Faulty Circuit Card Method This page is for your notes System Messages System Messages System Initialize Message no System Message Message no System Message Reset Interrupt B15 B11 ➃ Data Load Result after restartProcessing ➂ Related Call Information Reference See , .2, for the repair procedureCPU Clock Down ➁ Male-CPU Restart Information FF SUP Level Infinite Loop ➇ Data Analyzed by NEC Engineers ➃ System Controlling Port B➅ CPU Changeover Factors ➆ System ALM ➀ Information on Self-CPU Restart After detection of a clock faultMemory Failure = CPU #0/CPU #1 ➂ B-level Infinite Loop B1-Level Infinite Loop Permanent ➀ ➁ ➂ B1-Level Infinite Loop Temporary ➀ Mate-CPU Restart Information Mate CPU Failure ➀ ➁ ➂ ➃ Abnormal Interrupt Both TSW Failure Permanent TSW Failure Permanent Detected B7 b6 ➀ TSW system in which a fault isBoth TSW Write Failure ➂ Data Analyzed by NEC Engineers TSW Write Failure ➁ Clock status of No TSW ➀ TSW card in which a fault isBoth TSW Clock Failure TSW Clock Failure ➀ ➁ ➂ ➃ ➄ Both PLO Failure DCS Input Route Route Of Input Clock ➁ Valid Information bit for Scan Data PLO Failure System Messages ➁ Kind of failure ➀ MG number of fault detectionModule Group Down Failure NON TSW ACT Change Report ➆~➉ Status of ST-BY side TSW card ➂~➅ Status of ACT side TSW card Dlkc Data Transfer Failure Permanent ➀ System status of faulty Dlkc card➂ Details on Switching Network Dlkc Data Transfer Failure Temporary Connected With Primary Oscillator M-OSC External Clock PLO Restore Location ➀ Faulty Circuit Card MountingLevel Infinite Loop Permanent ➁ PM Restart Type Level Infinite Loop Temporary Lock-Up Failure Permanent Lock-Up Failure Temporary ➀ Faulty Circuit Card Location 48V Over Current Busy state and stops supplying power➀ Location of faulty PM Ground Failure ➀ Location of faulty circuit card➁ Location of faulty circuit card Valid only when the kind of fault is 08H ➀ Location of PM Lens with a fault➁ Kind of fault ➂ Time Slot No. of fault This data is ➂ ➃ ➂ ➃ Digital Line Failure ➀ Location of faulty line Digital Line RestoreThis message displays when a digital line fault is restored Detection ➀ Unit and MG number of faultBoth TSW Ready Failure TSW Ready Failure Detection Reference See , .4, for the repair procedure Dlkc Ready Failure ➀ Details on faulty Dlkc card MUX Ready Failure ➀ Unit and MG number for MUX card with ready fault➁ MG and system number for faulty MUX card Reference See , .3 and .4, for the repair procedure Both MUX Ready Failure ➀ Unit and MG number for MUX card with the ready fault PCI Card Failure ➄ Error status on PCI slot ➀ Detection of PCI restoration PCI Card Failure Recovered Slot ➄ Details on error restoration PCI NON Fixed NON Reference See , , for the repair procedureSystem Failure ➀ Probable cause for failure RGU & Howler Failure Line Load Control Start Line Load Control Stop ➄ The called station number When type of connection is Station connectionBad Call Notification ➁ ➃ Station number see table b7 b6 b5 b4 b3 b2 b1 b0 ➅ Remote Route No When type of connection is Trunk connection➄ Remote Route No ➇ Not used ➈ Time Slot Number of Link ➉ Not used ➆ Called Trunk No B4-b7 When type of connection is ACD Trunk connection System Messages ➀ Test Item b0-b3 is valid only for Outgoing trunk test STA-Test Connection Data Error no Meaning Error Numbers and Their Meanings = SST, WT = SDT = TRG = Sdtt ➇ Tested Route No ➀ ➁ ➂ ➃ ➄ ➅➆ ➇ ➈ ➉ 11 Emergency Call Assigned at Attendant Desk Console Emergency Control Start➀ Route Selection Time Pattern No ➀ Suspension of Emergency Control Emergency Control Stop Calling station No. See table When calling party is StationAbnormal Call Duration Data ➀ Calling party information ➃ Called party information When calling party is ATTCON/DESKCONWhen calling party is Trunk Route No. and Trunk No. See table OG Call to outside IC Call from outside ➄ Called Party InformationStation to Station Call Type of called party 00 = Station 01 = Attendant Console FS = 0, FE = 0/1 Smdr Output Buffer Overflow Alarm➀ Detail Information B7 b6 b5 b4 b3 b2 b1 b0 ➃ Overflow Rate FS = 1, FE =➂ Overflow Rate FS = 3, FE = FS = 2, FE =➁ Smdr Group No ➂ Port No ➀ Detail Information Smdr Output Buffer Overflow Release ➁ Load Status System Initialize With Data Load System Messages System Initialize CPU MBR Key Turn on CPU MBR Key Turn OFF ➀ System status of TSW card TSW MBR Key Turn on TSW MBR Key Turn OFF Operation TSW PLO Key Turn on TSW PLO Key Turn OFF ➀ Frame No. and its kind Almc MB Key Turn on Almc MB Key Turn OFF PM MB Key Turn on ➀ Location of faulty Line/Trunk card b7 b6 b5 b4 b3 b2 b1 b0 PM MB Key Turn OFF NCU MB Key Turn on ➁ Location of faulty PFT card NCU MB Key Turn OFF ➀ Performed Diagnosis Item Cyclic Diagnosis Normal Index 00H Routine Diagnosis Start➀ Performed Diagnosis Item ➁ Pending Diagnosis Menu SYS1 ➂ Verification of Drive Number 10H Program Memory Verification Normal End➀ Routine Diagnosis ➁ Information on HD ➂ Verification of Data Memory 20H Data Memory Verification Normal End➁ Verification of HD Changeover 30H TSW ACT/STBY Changeover Normal End➁ Active TSW system after 40H CPU ACT/STBY Changeover Normal End Ineffective Hold 50H No Trunk Ineffective Hold➁ MG and Unit of No. of Trunk 70H Call Forwarding Memory Clear Normal End A0H Periodic Back-up Normal ➁ Information on Periodic Backup➂ Backup Data to No system ➃ Backup Data to No system C0H Detection of Remaining Link Normal End For Release 4 or later Cyclic Diagnosis Information Error Detected➀ Detected Error Item B7 b6 b5 b4 b3 b2 b1 b0 ➃ Data analyzed by NEC Engineers 10H Program Memory Verification DiscrepancyDiagnosis ➁ Verification of HFD number Diagnosis ➁ Verification Impossible of HD 11H Program Memory Verification Impossible HFD Fault➀ Error detection by Routine ➃ Data analyzed by NEC Engineers ➄ Error Drive 12H Program Memory Verification Impossible Fault at CPU side Diagnosis ➁ Verification of HFC 20H Data Memory Verification Discrepancy ➄ Single Code 21H Data Memory Verification Impossible HFC Fault➃ Error Type B7 b6 b5 b4 b3 b2 b1 b0 Diagnosis ➁ HFC Impossible Verification ➅ Data analyzed by NEC Engineers ➆ Error Drive ➂ -➅MUX card ACT-side linkage condition 30H TSW ACT/STBY Changeover Failure➁ Active TSW No ➆ -➉MUX card Stby linkage condition B7 b6 b5 b4 b3 b2 b1 b0 MUX card ACT-side linkage condition B7 b6 b5 b4 b3 b2 b1 b0 31H TSW ACT/STBY Changeover Failure MUX FaultDetected Error Item Active TSW No ➆ -➉MUX card Stby linkage condition B7 b6 b5 b4 b3 b2 b1 b0 Diagnosis 41H CPU ACT/STBY Changeover Failure 42H CPU ACT/STBY Changeover Failure 43H CPU ACT/STBY Changeover Failure PCI Fault ➁ ACT system after changeover ➂ Lens of Ineffective Hold Trunk G, LV 50H Trunk Ineffective Hold DetectedDiagnosis ➁ Lens of Trunk Ineffective Hold MG, U 51H Trunk Ineffective Hold Detected and Released ➄ ➅ ➆ ➇ ➈ 11➉12 52H Trunk Ineffective Hold Detected Impossible Was stopped 70H Call Forwarding Memory Clear NG Abnormal End A0H Periodic Backup Abnormal EndError detection by Routine Diagnosis Information of Periodic Backup Refer to No. ➂ Refer to No.➃ Refer to No.➄ C0H Detection of Remaining Link Abnormal End ➁ ED Error Data PLO MB Key Turn on PLO MB Key Turn OFF 13-A CCH Clock Failure ➀ Location of faulty CCH/DCH card CCH C-Level Infinite Loop Failure Permanent 13-B 13-C CCH C-Level Infinite Loop Failure Temporary CCH Lock-Up Failure Permanent 13-D 13-E CCH Lock-Up Failure Temporary CCH B-Level Infinite Loop Failure Permanent 13-F 13-G CCH B-Level Infinite Loop Failure Temporary ➁ Data Analyzed by NEC Engineers 13-HCCS Link Failure Permanent ➂ Probable cause for failure Ccitt Factor Error CCS Link Failure Temporary 13-I ➂ Probable cause for the failure FLT ID Ccitt Factor Error Restoration From CCS Link Failure ➁ CKT No. of faulty circuit13-J 13-K CCH Reset Interrupt Failure ➀ Accommodated location B7 b6 b5 b4 b3 b2 b1 b0 This message displays when a digital line failure occurs➁ Kind of Fault B7b4 b3 b2 b1 b0 13-N 13-O Digital Line Failure 13-P ➀ Accommodated location 13-Q DRU Battery Operation ➀ Accommodated location 13-RDRU Line Operation ➂ Location of faulty circuit card 13-Z Power Failure➀ MG No. and Unit No. of fault detection ➁ Kind of Power ➁ Lens of VPS with the failure This message displays when a VPS failure is detected15-A VPS Failure Temporary 15-B VPS Failure Permanent ➀ Lens of VPS with the failure VPS Restore15-C Become all busy 16-A Inside Trunk All Busy➀ Intra-Office trunks that have Trunk Name RouteTrunk Name Route ➂ Virtual Tie Line Call Header 16-B Virtual Tie Line Set Report➁ Virtual Tie Line Call Header Accommodated Location 16-C Virtual Tie Line Cancel Report ➀ Virtual Tie Line Call Header 16-E Virtual Tie Line Set Time Out Reason Class Kind Data Reason Kind Value Call Source System Messages Reason Class Kind Data Reason Kind Value Invalid message class Case of Station OG/ATT OG/ATT Tandem Connection 16-FSender Start Time Out ➆ OG route number Hex B7 b6 b5 b4 b3 b2 b1 b0 ➄ Tenant No. of calling station Hex. b7 OP data 0/1➅ Optn data Number of digits dialed by caller ➇ Oprt data➈ Trunk No. of OG trunk ➉ Trunk No. of sender ➁ IC route number Hex Number dialed by caller See table B6 b5 b4 b3 b2 b1Case of Tandem Connection ➀ Type of connection ➂ Oprt data ➇ Oprt data Number dialed by caller See table B7 b6 b5 b4 b3 b2 b1 b0 IOC0 IOC1 ➀ Faulty Port No16-K Port Line OFF 16-L Port Line Restore 16-M Hard Clock Failure 16-N Hard Clock Restore 16-T IOC Failure Temporary This message displays when the IOC card fails➁ Cause for fault IOC Failure Permanent 16-U 16-X Station Exchanged Report ➀ Error codeError Code HEX Failure ➁ Tenant No. of calling station B4-b7 B0-b3 ➁ CKT No 17-ACCH MBR Key Turn on ➀ Location of CCH/DCH card B7 b6 b5 b4 b3 b2 b1 b0 17-B CCH MBR Key Turn OFF ➀ Location of CCH/DCH card 17-CCCH MB Key Turn on 17-D CCH MB Key Turn OFF ➀ Tenant No B7 b6 b5 b4 b3 b2 b1 b0 ➁ Changing Method 17-HDay/Night Change Information Night Mode 2 available only for Japan IOC MB Key Turn on 17-O 17-P IOC MB Key Turn OFF IOC MBR Key Turn on 17-Q 17-R IOC MBR Key Turn OFF ➀ Condition of Dch 23-PDCH Back-Up Automatic Change Start/End System Messages DCH Back-Up Manual Change Start/End 23-Q System Messages ➁ Scan Data 23-YMUX Clock Failure ➂ Scan Data 23-Z Both MUX Clock Failure➀ MUX card location ➀ Port No. of the MAT logged in/out b0-b2 I/O Port No This message displays when the MAT is log-in or log-out26-N MAT Log ➃ User Group No. UGN Hex When a call is originated from a station26-R Call Trace Output Data Hex Actual Meaning Blank ➉ User Group No. UGN Hex Information on Called Party Informer When a call is originated from a trunk Detailed meanings are as follows ➀ ➁ ➂ ➃ ➄ ➅ ➇➆ 26-V LAN Interface Error Report Error Code Output Data Definition Hex Not used Kind of ErrorDetails on Detected Error 12 ~ 24 Not used When 9 =05 OAI / 07 MIS 26-W LAN Interface Release Report ➈ Application Type When ➈=03 Smdr / 04 MCI➉ Device Number of recovered client PC Recovery Information ➁ RLS Data 33-A MUX Clock Restore ➀ MG Module Group SDT Alarm Warning➁ Details on alarm 33-B =-/VC-11 Path Trouble ➂ Alarm-detected HWRepair Procedure 33-C SDT Alarm Trouble Repair Procedure NDA-24300CHAPTER ➁ Details on the fault 33-D SDT Alarm Restore ➁ Detailed information 33-ESDT Interface Change Notify This page is for your notes Circuit Card Mounting Face Layout Unit/Circuit Card Replacement ProcedureLPM Accommodating Unit/Circuit Card Replacement Procedure Precaution LANIPZ-PC19 GATEPZ-GT16 UNIT/CIRCUIT Card Replacement Procedure UNIT/CIRCUIT Card Reference Item Remarks Operating Procedures PZ-IO27 Note CPR Replacement Procedure How to Replace the CPU Removal of Front Panel and Top Cover from CPR Circuit Card Accommodation into the New CPR Lani PZ-PC19 Isagt PZ-GT13 Reattachment of CPR Top Cover and Front Panel Accommodation of New CPR into LPM Insertion of New HFD into CPR By using the two screws, fasten the new HFD onto the CPR Replacement Procedure Refer to -2for CPR face layout Refer to -3to replace the CPU Section Palm connector yet IMG0 lamp on the DSP flashes EMA SUP lamp on the EMA card goes OFF Top Cover Front Panel 10 Insertion of Isagt and Lani Cards 11 Reattachment of CPR Top Cover and Front Panel CPR LPM 13 Insertion of New HFD Into CPR EMA Card Replacement Procedure YES END OPE lamp on the IOC card goes IOC Card Replacement ProcedureReplacement Procedure UNIT/CIRCUIT Card Replacement Procedure CPU System Changeover Refer to .1.2 in Chapter Power Supply Unit Replacement Procedure UNIT/CIRCUIT Card Replacement Procedure Keep MB switch UP Misc Card Replacement Procedure ALM RST button is used to reset the alarm lamps only Tswm Accommodating Circuit Card Replacement Procedure Circuit Card Reference Item Remarks Function Name Misc BUS GT Card Replacement Procedure CPU OPE CPU DSP = OFF GT Card Replacement ProcedureSystem changeover of GT from ACT to Stby mode UNIT/CIRCUIT Card Replacement Procedure IMG0 CPU DSP = Flash green IMG1-3 CPU DSP = OFF TSW Card Replacement Procedure 16 System Block Diagram TSW and Other Speech Path Echelons Use extreme care when operating the keys on the circuit card TSW Card Replacement Procedure UNIT/CIRCUIT Card Replacement Procedure They are all steady-green TSW ACT lamp on the new card goes OFFTSW ACT lamp on the new card Remains OFF Dlkc Card Replacement Procedure Refer to -16and Figure OFF PLO Card Replacement Procedure OPE lamp on the new card is OFF PWR SW Card Replacement Procedure Misc Card Replacement Procedure 18 Circuit Card Mounting Face Layout of PIM PIM Accommodating Circuit Card Replacement Procedure Circuit Card Reference Item Remarks Function Name Keep MB switch set at UP 1 LC/TRK Circuit Card Replacement Procedure MUX Card Replacement Procedure MUX ACT lamp on the new card is red Refer to -16and Figure Procedure to Replace Optical Fiber Cable SDT Card Replacement Procedure OPE lamp on the PA-SDTA card is steady-green Procedure to Replace PA-SDTA/PA-SDTB card UNIT/CIRCUIT Card Replacement Procedure Green OPE lamp on the new card is red OPE lamp on the card goes OFF PWR Card Replacement Procedure UNIT/CIRCUIT Card Replacement Procedure Replacement Procedure Fanu on Topu Fan Unit Replacement 20 Preparation for Fanu Replacement Fans on Topu 21 How to Replace Fanu Fans on Topu OFF Replacement Procedure Fanu in Fan Box 23 How to Replace Fanu Fans in Fan Box PZ-IO27 PZ-GT16 and PZ-GT13 Isagt CPR Cooling Fan Replacement 25 Extraction of CPR from LPM 27 How to Remove the Cooling FAN 28 Fuses Used by System Fuse Replacement 30 Fuse Locations Within System 31 Fuse Location Within Tswm 32 RGU Fuse Blown Fault Flowchart 33 DC -48V Fuse Blown Fault Flowchart Faulty Item Faulty Situation Reference Section Fault Repair Procedures Fan Unit Fault Fault Repair Procedures Faulty Situation Reference Section Line Fault Line Control Check Point Line Fault When Dial Tone DT Cannot Be Heard Check the faulty line on the MDF Line Fault When Dialing Results in Wrong Connection Line Fault When Bell Does Not Ring When Call Cannot Be Answered and Speech Cannot Be Made Dterm Fault END Trunk Faulty Situation Reference Section Trunk Fault Timings for Trunks Timings for Senders Controlling Trunk Circuit Cards and Speech Path Trunk Control Trunk ORT, SND, CFT Fault Trunk COT, TLT, DTI Fault Replace the Dterm with a spare TLT RA RB TA TB ATTCON/DESKCON Control ATTCON/DESKCON Fault ATT Connector Cabling and Connector Leads Accommodation ATTCON/DESKCON Fault ATTCON/DESKCON Replace the ATTCON/DESKCON with a spare Fault Situation Reference Section Unit Fault Unit Control Block Diagram Dual Configuration Unit Control Block Diagram Single Configuration Unit Fault Fault Related to Speech END For Single Configuration END Unit Fault When Dial Tone DT Cannot Be Heard Circuit card UP and extract For Single Configuration Circuit card UP and extract Start Spare, and check it If the connection is set up, setFaulty system into Stby Replace the MUX circuit card with a Faulty Situation Reference Section Speech Path TSW System Fault Speech Path Block Diagram IMG2 PIM TSW Write Failure For Dual Configuration Speech Path System Fault Fault Related to Speech END For Single Configuration END Speech Path System Fault When Dial Tone DT Cannot Be Heard Speech Path System Fault Stby Side Has Become Faulty END EMA circuit cards Control System FaultCPR TSW MUX CPU Controlling Block Diagram Lani Isagt Control System Fault Fault Occurs Intermittently END Control System Fault Stby Side Is Faulty 10 Alarm Bus Cable Connections Diagram IMG Fault of Alarm Indicating Panel Alarm Indication Fault 11 Cable Routing for Alarm Indications Fault That Cannot Be Detected System configuration Power Supply Fault System configuration 16shows the power supply system for PIM 18shows the power supply system for Tswm Fuse Blown Fault Circuit Breaker OFF Fault in PWR Supply Fault Supervision Fault of Alarm Lamps on PWR Supply 19 Circuit Diagram of Fan Unit and Thermal Unit FAN Unit Fault If the voltage is -48 Fan Unit FaultPIM 20 Dial Tone Connection Tone Fault Tone Fault 21 External Hold Tone Supply Block Diagram 22 System Down Fault Repair Sequence System Down Fault When Cause for Fault Cannot Be Identified END When Faulty Circuit Cards Can Be Assumed From System Message Ccis Line Control Common Channel Interoffice Signaling Ccis Line Fault Check by replacing CCH/CCT card with a spare Specific CCH/CCT Card Is Faulty Fault of CCH, DTI and Related Flat Cable Isdn Line Control Integrated Service Digital Network Isdn Line Fault Check by replacing the DCH/PRT card with a spare Specific DCH/PRT Card Is Faulty Fault of DCH, DTI, and Related Flat Cable Start END Hard Time Clock Fault This page is for your notes Kinds of Alarm Indications Alarm Indications System Operations How to Stop Alarm IndicationsAlarm Indications on Topu Lamp Color Function Contents Automatic Printout to System Message Dedicated Printer Variable Alarm IndicationCommand Command Full Name Collection of System Messages Indicating Method Recovery ProcedureDisplay on MAT Indication of Lockout Stations Rlst Line Load Control Operating Procedure Line Load Control Operations on ATTCON-Cancelling Cancelling Line Load Control Key Operations on DESKCON-Setting 11 Line Load Control Indication Deskcon IOC Line Monitor Message Content Line Management Make-Busy/Make-Busy Cancel of Station and Data Terminal Class Change and Number Change of Station and Data Terminal Make-Busy/Make-Busy Cancel of C.O. Line/Tie Line Station Message Detail Recording System Smdr Line Management Commands Transmission Data to Smdr Equipment Ascii Code Charac Binary Digit Remarks TER HEX 14 Message Format for Outgoing Call 15 Message Format for Incoming Call 16 Message Format for Station-to-Station Call For an Attendant Orig = 1 Data showing Attendant Number Data which indicates Call End Time is as follows Call Start/Call End Time InformationData which indicates Call Start Time is as follows Data which indicates the Called Number is as follows Called Number Data which indicates the Account Code is as follows Account Code/Authorization CodeData which indicates the Authorization Code is as follows Condition B Information Route Advance Information Call Metering Information Text Format of Centralized Billing Fusion Kind Contents Outgoing Incoming System Operations 17 Message Format for Outgoing Call Fusion 18 Message Format for Incoming Call Fusion 19 Message Format for Station-to-Station Call Fusion Data = 08 Condition B Information ReferenceData = 02 Calling Party Information Station Number FPC1 Attcon Data = 16 Automatic Number Indication Text sending direction Client Server Text Format of Smdr TCP/IP Interface Xxxxx Type Kind Description Measurement Traffic ManagementKind of Traffic Measurement 5shows the kinds of traffic measurements Deskcon Atrfn Operating ProcedureStep Asyd Asydn Atrf 21 IPX MAT Menu Display Image Example Name Data Output Details on DTFD/DTFDN CommandFull Command Name Print Log Data collecting LogTool Buttons Collect Data Stop Down Display AreaSave Text File System Operations Office Data Preservation Office Data ManagementOffice Data Stored Locations 25 Office Data Change Procedure Office Data Management Procedure 26 Office Data Change Procedure 27 Backup Commands One-Touch Speed Call Memory Data Management Individual Speed Calling Data Hddmat commandData Management Commands Dcon Test Operations of Various Kinds Designated Connection Test Station Test Item Content of Confirmation Remarks Designated Connection Test Procedure Register Test Procedure SRV=SSC, SID=17 Sender Test Procedure 31 3-Party Conference Test Procedure Party Conference Trunk Test Procedure 32 3-Party Conference Test Connection Diagram 33 Tone Test Procedure/Connection Diagram Tone Test Procedure Tone no Kind of Tone Remarks 34 Interrupt Ringing IR Test Procedure/Connection Diagram Interrupt Ringing IR Test Procedure 35 Trunk Test Procedure Trunk Test Procedure 36 Trunk Test Connection Diagram Designated Connection Test DESKCON/ATTCON Trunk seizure by access code dialing Spdt Bad Call Notification ASYD, SYS1, INDEX86 Routine DiagnosisRelated System Data INDEX304 INDEX89INDEX90 Routine Diagnosis Result Call Forwarding Data Clear See IndexHDD see Index Belonging Isagt and LANI, are also changed over System Control Procedures Does not affect any other systems 37 Switching Network General Block Diagram 38 How to Check LEDs and SW Keys for System Changeover IMG0 39 How to Check LEDs and SW Keys for System Changeover IMG1 IMG 2/3 41 How to Check Status LEDs Type Operations Remarks How to Control CPU Block 42 System Block Diagram Switching Network Between CPU and GT DSP Front View Manual System Changeover of CPU 45 CPU Changeover via MBR Key LANIPZ-PC19 ISAGTPZ-GT13 Forced Changeover of CPU Changeover of Switching Block Type Operations Remarks How to Control Switching Block Manual System Changeover of Speech Path System Dlkc PLO CPR Isagt CPU Lani Isagt PZ-GT13 Lani PZ-PC19 49 TSW/DLKC/MUX in ACT Mode 51 Speech Path System Changeover via Active GT MBR Key 53 Check of Active PLO Manual System Changeover of PLO 54 PLO in ACT/STBY Mode 55 PLO Changeover via MB Key Flip the MB key on the PLO card. Refer to Figure Initialization General CPU DSP#1 IMG0 System Initialization by Turning on Power SupplyCPU DSP#0 Type Description System Initialization by Key Operations on Topu 57 Conceptional Diagram of Initial Program Load 58 Related Keys and LEDs for System Initialization END ON. on Line Program KEY NON LoadSystem Data KEY NON Load DSP of active CPU Is ON. on Line System Data KEY Load Program KEY Load Program KEY Load System Data KEY → NON Load Active CPU light steadily green Lamps on the EMA System Initialization by Keys on CPU Front PanelStart EMA PH-PC40 Check ACT0/ACT1 System Initialization by Sinz Command MB lamp has turned on Return MB switch toPrevious position after How to Turn On Whole System How to Turn ON/OFF Whole System 60 How To Turn OFF the Whole System How to Turn OFF Whole System Office Data have been already installed in the HD Have already been installed in the HD. Office Data has notBeen installed Procedure #2 see Table On Line ➀ When Power is OFF ➁ When Power is on OFF LineSet Sense switch at 1 DM Line CPU Set Sense switch at 2 DM Load Restart on the DSP of active DM Load Restart on the DSP Set the Sense switch at On Line END This page is for your notes Flow of Procedures Routine Maintenance Procedure Test EQUIPMENT/TOOLS Purpose Remarks 1shows the tools and equipment required for test proceduresRoutine Maintenance Procedure Required Test Equipment and Tools Time Procedure Reference Section Remarks Routine Maintenance Procedures Ambient Conditions in Switch Room Check Alarm Check MAT/Printer Check Collection of System Messages Display of Locked-out Station Fan Unit Check Refer to , Fan Unit Fault, in Chapter Alarm Tests Main Power System Check Trunk RGU Check Attendant Console Check ATTCON/DESKCON Check PM WED Desk Console Check System Check Routine Maintenance Check Lists Condition And Cause Procedure and Parts Used Right Connection Test-ATTCON/DESKCON Test Type Test Item Connection DiagramConnection test diagrammed to Trunk/Tie Line DP/PB Register/Sender Trunk RSTORT Function Perform the test by specifying SND0 RSTFunction Trunk no Sender Speech Path for Each PIM, and Ringing Generator Unit Digital Conference FunctionMessage displays as a result Test Function Speech Release Remarks Trunk no PIM1 PIM2 PIM3 PIM4 That the station ringsMounting Location Check Module Name Unit Name Deskcon Test Item Connection DiagramAttendant Console ATTCON/DESKCON Speech Release Deskcon no Call Termination Call OriginationAttcon Maintenance Commands Dteln Maintenance Commands Maintenance Commands Parameters Allc Assignment of Line Load ControlFunctional Outline Type Almg Assignment of Alarm Grade DataLMP GRD Atrf Assignment of Traffic Measurement Order Functional Outline Bosd Back Up One-Touch Speed Call Memory Data Result Cadsd Continuous Assignment of Station DataExample Input data STNEND=200 SFC TEC=DP/PB RSC When Delete is selected in the Type selection list box Carr Continuous Assignment of Alternative Route Restriction OG Lgrt IC Lgrt START/ENDIC Lgrt TKEND=21 When Assign is selected in the Type/KIND selection list boxCatk Continuous Assignment of Trunk Data Data Entry Result Tkend When Delete is selected in the Type/KIND selection list boxTkstart TYPE=1 Level → Details on Trunk Arrangement Type TYPE=3 Group → TYPE=5 Unit → Chapter Interval Broadcasting Interval Cbcn Control of Broadcasting for NDMFPC FPC of the designated Node Note Link Ccse Change of Common Signaling Channel EquipmentCCH Lens MG=XX, UNIT=X, GROUP=XX STS1 Cdbu Change of Dch BackupCNT STS0 System Cmod Change of System ModeDevice =CPU =TSW Cmwl Control Message Waiting Lamp Teln Cmwlt Control Message Waiting Lamps Telephone NumberUGN =Urgent Cprs Controlled Alternate PRSCsPriority Restriction Class N/U =Normal Cscl Continuous Change of Station Class Cstn Continuous Change of Station Number Dcbd Display of Call Block Entry Data NDA-24300CHAPTER CTK Dcen Display of Connection Trunk Lens Data for LDMClens CRT Connection Trunk Number 1-4095 Note Dcon Display of Connection StatusLEN CRT Connection Route Number 1-1023 Note Input data New/Old Show Details YES/NO Dftd Display of System Message Details Version Issue Date Group 00-23 SP No Digits Ascii 2 digits Diss Display of Program Issue Room Class ANX Dlen Display of Lens Data Floor =Ground=Underground FLR Dlsl Display of Lockout Station Lens This command prints the Lens of stations in lockout state STN Lens Dlss Display of Lockout Station Number Telephone Number max digits Dlsst Display of Lock Out Station Number Telephone NumberCount Station Number Max digits Dltel Display of Telephone Number from Lens for LDM Telephone Equipment Number Dntel Display of Telephone Number from Lens for NDMNID Network ID Note Unit U number Dpkg Display of Setting Port PackageInput Data Module Group MG number PKG Name Dpsw Display Package Switch StatusKind PMN Dstn Display of Station Data Dteln Display of Telephone Number Data for NDM Shcn CpgnCpen Shun DTF101 Display of Terminal Traffic Data DTF102 Display of Route Traffic Data DTF103 Display of Station Peg Count Data DTF104 Display of Attendant Peg Count Data DTF105 Display of Route Peg Count Data DTF201 Display of Service Peg Count Data DTF301 Display of UCD Route Peg Count Data DTF302 Display of UCD Group Peg Count Data DTF303 Display of Station Peg Count Data DTF501 Display of Attendant Answering Peg Count Data DTF601 Display of Connection Route Peg Count Data DTF602 Display of Connection Route Traffic Data DTF101N Display of Terminal Traffic Data for Fusion Network DTF102N Display of Route Traffic Data for Fusion Network DTF103N Display of Station Peg Count Data for Fusion Network Functional Outline DTF105N Display of Route Peg Count Data for Fusion Network DTF201N Display of Service Peg Count Data for Fusion Network Functional Outline Functional Outline Functional Outline Functional Outline Functional Outline Functional Outline Data Install Procedure Flinst File Install HFD0/HFD1 Hddfdd Data Control Between HDD and FDDInput data System Select File Name Select Auto Verify Afterward Hddmat Data Control Between HDD and MAT Hddmatn Data Control Between HDD and MAT for NDM Hdfp HDD Format of PBX =Make Busy Outgoing Mbct Make Busy of Connection Trunk for LDMMake Busy Information 0/1 =Make Busy Mble Make Busy of Lens Input data MG Unit Group Display data =Make Idle =Make Busy Mbpm Make Busy of Port Microprocessor Mbrt Make Busy of Route Make Idle Mbrtlr Make Busy of Route-Logical Route NumberLgrt Mand as to the Internal route number and its meaning. Note Port no Mbsm Make Busy of System Message Printout Mbst Make Busy of Station This command assigns the Idle/Busy status of stations Make Busy/Make Idle Display Data Exit Click to exit this commandMbstt Make Busy of Station Telephone Number Mbtc Make Busy of Trunk-Continuous =Make Busy Bothway Note Mbtclr Make Busy of Trunk-Continuous-Logical Route NumberLogical route number allocated to the Route Number. Note Trunk Number Note Mbtk Make Busy of Trunk This command assigns the Idle/Busy status of trunks Mbtklr Make Busy Trunk-Logical Route Number Memhdd Data Control Between Memory and HDD Input data Direction Select MEM to HDD Memhddn Data Control Between Memory and HDD for NDM FCH Number Mfch Make Busy of FcchFchn Nating Port Microprocessor to MAT Pmbu Port Microprocessor Back Up This command clears the fault indications Ralm Release Alarm OK/NG Ralmn Release Alarm for NDMStatus Result of releasing the alarm Information Rlst Release Station/Trunk=LENS External/Internal Route Number Trunk Number Rlstt Release of Station/Trunk Telephone NumberTelephone Number Trunk Connection Trunk PCN ERNGRN CSN/ZTN =System Initialize Office Data Load & System Initialize Sinz System InitializationKind of Initialization =System Initialize Type 1 By MG Spts Scanning of Port Status Exit Type of Circuit Card Function Name Port Status Report MG, Unit Display Type 2 By MG, Unit = Unassigned Port Type 3 By MG, Unit, GroupDisplay of Scanning by Designating Group Idle = Idle Trunk Class TCL Srts Scanning of Route Status Number of Idle/Busy TK Srtslr Scanning of Route Status-Logical Route NumberInterval Interval Time of two scan Display Data Route of Route Number Area Xhfd X-RAY HD or FDD DiagnosisFunction Message Fault DriveFault Sector