Devices on Poll List Display field, State | Paradyne 6800 guide

Modem/DSU Commands

Page 2

Page 2 displays the current active devices on the poll list for the specified device, and allows you to add or delete devices to the poll list, or to skip polling for a specific device. It also enables you to set the CNN event for the specified device(s). Figure 2-14 is a sample of the second Change Poll List input form.

Figure 2-14. Change [Device] Poll List Input Form, Page 2

This input form contains the following fields:

DEVICES ON POLL LIST (Display field)

Displays the names, network addresses and the current state of devices that are currently on the poll list(s) of the specified device(s).

State

Use this field to remove or skip devices on the poll list.

Enter skipped to stop polling a device. The device remains on the poll list but it is not polled. The device is skipped during polling and alert reports are not received. However, the primary data channel remains enabled, and commands can still be sent to the device.

Enter active to resume polling of a skipped device.

Enter delete to remove a device from the poll list.

A pop-up menu is available listing valid selections.

6800-A2-GB31-20

January 1997

2-61

Image 84

Paradyne 6800 manual Devices on Poll List Display field, State

Contents

Comsphere 6800 Series Network Management System Warranty, Sales, and Service Information Trademarks Table of Contents Comsphere 6800 Series Network Management System List of Figures Comsphere 6800 Series Network Management System List of Tables Objectives and Reader Assumptions Related Documents Command Reference Manual Administrators GuideComsphere 3900 Series Modems, Models 3910 Analysis 6510 Automated Network Management System Reference Introduction Overview Series NMS Communications Products NMS-Supported APL ModemsNMS-Supported Direct Distance Dialing DDD Modems NMS-Supported Data Service Units DSUs Paradyne APL Modems and DSUs via Analysis GatewayNaming Conventions Command Support ± Customer Configurations Command AccessDevice Addressing Test not sent. Test device mismatch Shortcut for Command Access Wildcard CharactersMultiple Entries Format for Documenting Commands in this Manual Access LevelAbbreviation Related Commands RestrictionsRoutine Schedule Command Input Forms Required FieldsOptional Fields Crt default Display-only FieldsCarried-over Fields Destination for results Delayed PrinterQueue Schedule execution Times Valid entries are hhmm, hhmmam or pm, hh-hhmm, and allmmHhmmam or Weekly Results Forms MonthlyDays of the month Help MenusForms For Screen Input Fields Selecting Fields Listed in Tabular Form Modem/DSU Commands Overview RoutineYes ScheduleYes Related Commands None Abort abortAbort Input Form Abbreviation abort Abort Command Results Form Abort type Required fieldSubnetwork Selective Acquire Device Poll List acpl Disruptive ± Dataphone II APL Modems Acquire Device Poll List Input Form Acquire Device Poll List Results FormSet CCN event Required field Automatic Network Test ant Automatic Network Test Input FormAbbreviation ant Port number Required field Automatic Network Test Results Form Number of device failuresPassed Test ± All tributaries have passed Calibrate Tributary Transmitter ctt Calibrate Tributary Transmitter Input FormControl devices Required field Tributary devices Required field Calibrate Tributary Transmitter Results Form Calibrate Tributary Transmitter Results Form Call Detail Display cded Call Detail Display Input Form Dates included Call detail available from Display fieldCall detail available until Display field Days included Call Detail Display Results Form Call Detail Display Results Form, Call Duration Distribution cdud Call Duration Distribution Input Form Call statistics available from Display field Call statistics available until Display fieldThreshold Call Duration Distribution Results Form Periods Call Duration Distribution Results Form, Call Duration Distribution Results Form, Call Fault Criteria cfc Call Fault Criteria Input FormsAbbreviation cfc Restrictions None RoutineNo ScheduleNo Action upon exceeding minimum average Action upon not meeting minimum averageIncoming calls/sample Required field Maximum number of non-answered calls/sample Required field Report-fault Make-busy-and-report-faultAction upon exceeding maximum number Required field No-action Call Fault Criteria Results Form Call Fault Read cfr Call Fault Read Input FormCall Fault Read Results Form Abbreviation cfr Restrictions None RoutineYes ScheduleYes Entries into data mode answered Entries into data mode answer and originateTotal seconds in data mode answer and originate Incoming calls answered and non-answered Comsphere 6800 Series Network Management System Call Message cm Call Message Input FormAbbreviation cm Call Message Results Form Call Occurrence Distribution cod Call Occurrence Distribution Input Form Call Occurrence Distribution Results Form Call Occurrence Distribution Results Form, Call Test ct Call Test Input FormAbbreviation ct Restrictions None RoutineYes ScheduleYes Number to dial Required field Call Test Results Form Test type Required field for 3900 Series modemsCall test passed No dial tone No ringing tone Routine Schedule Related Commands Change Address chaChange Address Input Forms 2 for Comsphere Device in ADp Mode Number of device profiles to update Required field 2 for Comsphere Devices in Dpii Mode Dataphone II mode local address Required fieldAdvanced mode address Required field Change Address Results Form Set CNN event Required field Requested local or network address Original link level addressNew link level address Change Call Directory chcd Change Call Directory Input FormAbbreviation chcd Restrictions None RoutineYes ScheduleYes Directory number Required field Telephone Number Modem/DSU Commands Set CCN event Change Call Directory Results Form Strap Change Canned Message chcm Change Canned Message Input FormsMessage number Required field Message Change Canned Message Results Form Change Directory chd Change Directory Input FormControl characters replaced by ? Display field Change Directory Results Form Directory values Required field Change Exception Reporting Thresholds chert Change Exception Reporting Thresholds Input FormsAbbreviation chert Restrictions None RoutineYes ScheduleYes Request Terminal Power list if Required field Digital list if nnnn errors Required fieldEnd to End list if nnnn inbound errors Required field End to End list if nnnn outbound errors Required field Circuit Loss Outbound list if nn dB Required field Signal Profile for 2096A and C Modems Change Exception Reporting Thresholds Results Form RSQ Change External Leads States chels Change External Leads States Input FormAbbreviation chels Restrictions None RoutineYes ScheduleYes Pin a output Required field Change External Leads States Results Form Test not sent. Test±device mismatch Change Line Designator chld Change Line Designator Input FormChange Line Designator Results Form Abbreviation chld Restrictions None RoutineYes ScheduleYes Change Multiplexer chm Change Multiplexer Input Form Change Multiplexer Results Form Model Required field2096A 2096C 2096T 2144A 2192A Mux option Required field Change Options cho Change Options Input Forms Change Options Results Form Change Device Poll List chpl Change Device Poll List Input Form Devices on Poll List Display field State Change Device Poll List Results Form Add to active listAdd to skipped list Change Port Options chpo Change Port Options Input FormAbbreviation chpo RoutineYes ScheduleYes Change Port Options Results Form Change Port Speeds chpsp Change Port Speeds Input FormsAbbreviation chpsp Device speed Display field Port speed Change Port Speeds Results Form Change Protocol Mode chpm Change Protocol Mode Input Form Protocol mode Required field Change Protocol Mode Results Form 16. Change Protocol Mode Results Form Change Telephone Numbers chtn Change Telephone Numbers Input Forms 2 for 3400/4400 Series Modems Remote transmit numberRemote receive number Local transmit number 2 for 3600 Series Devices Change Telephone Numbers Results FormLocal telephone number Change Thresholds cht Change Thresholds Input FormsAbbreviation cht Restrictions None RoutineYes ScheduleYes Signal-to-noise ratio Required field Receive level high Required fieldReceive level low Required field Phase jitter 20±300 Hz Required field Change Thresholds Results FormFrequency offset Required field Non-linear distortion Required field Modem/DSU Commands Circuit Loss Inbound cli Circuit Loss Inbound Input FormTone frequency Required field Circuit Loss Inbound Results Form 18. Circuit Loss Inbound Results Form Circuit Loss Outbound clo Circuit Loss Outbound Input Form Circuit Loss Outbound Results Form 19. Circuit Loss Outbound Results Form Circuit Quality cq Circuit Quality Input FormCircuit Quality Results Form Abbreviation cq Restrictions None RoutineYes ScheduleYes NAN Receive level Signal/noise Signal qualityFar end delay Near end echo Bit Error Rate RetrainsBlown Startups Non-linear distortion Freq offset 1±10 Hz Modem/DSU Commands Clear Call Directory clcd Clear Call Directory Input FormClear Call Directory Results Form Configuration Change Notification ccn Configuration Change Notification Input FormAbbreviation ccn Restrictions None RoutineYes ScheduleYes Test state Required field Configuration Change Notification Results Form No events to report Category Update Command Configuration Change Notification Enable/Disable ccned Configuration Change Notification Enable/Disable Input FormAbbreviation ccned Restrictions None RoutineYes ScheduleYes CCN state Required field Modem/DSU Commands Daily Historical Utilization dhu Daily Historical Utilization Input Form Daily Historical Utilization Results Form Threshold fields 24. Daily Historical Utilization Results Form, Device Health and Status dhs Device Health and Status Input FormType Required field Device Health and Status Results Form 1 for Single Devices Network 1 for Subnetwork Devices 101 Device Test det Device Test Input FormAbbreviation det Test type Device Test Results Form Speed test is executed Dial dial Dial Command Input Form 28. Dial Command Input Form Protocol /4400 Dial Command Results Form Callback directoryOption strap area Disconnect existing call before execution Required field Dial Mode dm Dial Mode Input FormDial Mode Results Form Related Commands Dial Standby ds Related Commands Dial Mode dm Dial Standby dsDial Standby Input Form Dial Standby Results Form Digital Test dit Digital Test Input FormAbbreviation dit Tributary Devices Number of 100K bit blocks or duration of test secDuration of test dsu Digital Test Results Form Duration of test ddd Number of bits in error Requested number of 100K bit blocksNumber of 100K blocks attempted so far Requested number of 100K blocks Errored seconds Errored bitsTotal seconds Total bits Test outcome As pass or fail Requested duration of test Test outcome As pass or fail Speed at which test executed Disable/Enable de Disable/Enable Input FormAbbreviation de Device state Required field Disable/Enable Results Form Display Address dsa Display Address Input FormDisplay Address Results Form Display Alert Information dsai Display Alert Information Input FormDisplay Alert Information Results Form Abbreviation dsai 33. Display Alert Information Results Form 121 Display Call Directory dscd Display Call Directory Input FormAbbreviation dscd Restrictions None RoutineYes ScheduleYes Display Call Directory Results Form Call Only for 3400/4400 Series devices Strap Only for 3400/4400 Series devices Display Canned Message dscm Display Canned Message Input FormDisplay Canned Message Results Form Abbreviation dscm Restrictions None RoutineYes ScheduleYes Display Exception Reporting Thresholds dsert Display Exception Reporting Thresholds Input FormDisplay Exception Reporting Threshold Results Forms Abbreviation dsert Restrictions None RoutineYes ScheduleYes 36. Display Exception Reporting Thresholds Results Form, 37. Display Exception Reporting Thresholds Results Form, Display External Leads States dsels Display External Leads States Input FormAbbreviation dsels Restrictions None RoutineYes ScheduleYes Display External Leads States Results Form 38. Display External Leads States Results Form Display Line Designator dsld Display Line Designator Input FormAbbreviation dsld Restrictions None RoutineYes ScheduleYes Display Line Designator Results Form 39. Display Line Designator Results Form Display Options dso Display Options Input FormDisplay Options Results Forms Abbreviation dso Display Device Poll List dspl Display Device Poll List Input FormAbbreviation dspl Restrictions None RoutineYes ScheduleYes Display Device Poll List Results Form 40. Display Device Poll List Results Form Display Port Options dspo Display Port Options Input FormDisplay Port Options Results Form Abbreviation dspo 41. Display Port Options Results Form, Display Port Speeds dspsp Display Port Speeds Input FormDisplay Port Speeds Results Form Abbreviation dspsp 43. Display Port Speeds Results Form for 19.2 kbps Modem, Display Telephone Numbers dstn Display Telephone Numbers Input FormDisplay Telephone Numbers Results Form Abbreviation dstn Restrictions None RoutineYes ScheduleYes Line 1 telephone number of the device to be called Display Thresholds dst Display Thresholds Input FormDisplay Thresholds Results Form Phase jitter 20 ± 300 Hz Frequency offset Download Device Firmware dndf Download Device Firmware Input Form Remote device Required field Remote dial number Local master device Required field Link Participation Service Class Download Device Firmware Results FormDevice Protocol Mode ModelSoftware Version Serial Number EIA Status eias EIA Status Input FormEIA Status Results Form Abbreviation eias 151 Port LeadStatus Mark EIA Status Results Form for 3900 Series Modems 154 Port Lead Space End-to-End Test eet End-to-End Test Input FormAbbreviation eet 50. End-to-End Test Input Form Number of blocks Required field End-To-End Test Results Form 51. End-to-End Test Results Form Exception Reports er Abbreviation er Exception Reports Input Form 52. Exception Reports Input Form Exception test Required field Exception Reports Results Form Exception testDevices requested Total tests requested Total tests missing Number of unacceptable resultsNumber of acceptable results Percentage of unacceptable results 54. Exception Reports Results Form, Identity Command Results Forms Update device profile Required fieldIdentity id Identity Input Form Access module id 1 for 3400/4400 Series ModemsSpeed/Mux Async adaptors installed on ports Eye pattern board installed yes,noFacility restoral option Receiver composite facility speed 1 for 3600 Series DSUs 1 for Dataphone II Devices Application module info 1 for Comsphere 3800 Series DDD Devices 57 is a sample results form for Comsphere 3800 DDD devices Modem Configuration 1 for 3800 Series DDD DevicesAPL Multi-point Modem Strapping UK, or Italy Hardware Part Number 1 for Comsphere 3900 Series APL Devices 1 for 3900 Series Modems Wire List Directory lsd List Directory Input Form List Directory Results Form 59. List Directory Results Form Loopback lo Loopback Test Input FormTest type or state Required field Analog/local Digital V54-remote-digitalRelease Loopback Test Results Form Make Busy mkb Make Busy Input FormMake Busy Results Form Abbreviation mkb Daily scheduled updates Manage Call Statistics mcsManage Call Statistics Input Form Abbreviation mcs Restrictions None RoutineYes ScheduleYes Manage Call Statistics Results Form Store Call Detail Data Required fieldNumber of local 3800 Series modems Display field Modem Bit Error Rate Test mbert Modem Bit Error Rate Test Input FormRoutine Yes Schedule Related Commands Abort abort Been placed into a loopback state Modem Bit Error Rate Results Form Number of errored seconds Number of errored bitsNumber of total seconds Number of total bits 185 Offline Test ot Offline Test Input FormOffline Test Results Form Abbreviation ot Receive Signal Level rsl Receive Signal Level Input FormReceive Signal Level Results Form Abbreviation rsl Restrictions None RoutineYes ScheduleYes Receive Signal Quality rsq Receive Signal Quality Input FormReceive Signal Quality Results Form Abbreviation rsq Restrictions None RoutineYes ScheduleYes Receive Signal Spectrum rss Receive Signal Spectrum Input FormMode Required field Control Device Required field Receive Signal Spectrum Results Form Tributary device Remote Digital Loopback rdl Remote Digital Loopback Input FormLoopback Remote Digital Loopback Results Form Report Terminal Power rtp Report Terminal Power Input FormReport Terminal Power Results Form Reset reset Send Message snm Send Message Input FormSend Message Results Form Message Required field Send Tone snt Send Tone Input FormAbbreviation snt Send Tone Results Form Service Line sl Service Line Input FormService Line Results Form Service line state Required field Signal Profile sp Signal Profile Input FormSignal Profile Results Form Receive signal level Receive signal qualityEstimated block error Phase jitter Signal Profile for 2048A and C Modems 202 Standby Facility sf Standby Facility Input FormStandby facility state Required field Originate/ddd Reset-dbm-lockout Standby Facility Results FormRelease/apl-or-dds Leased-lookback Training Time tt Training Time Input Form Training Time Results Form 63. Training Time Results Form Transmit Test Pattern ttp Transmit Test Pattern Input Form Transmit Test Pattern Results Form Trending Reports tr Trending Reports Input Form 64 is a sample of the Trending Reports initial input form Trending test Required field CQ test group selection Trending Reports Results Form 65. Trending Reports Results Form ± Tabular, 66. Trending Reports Results Form ± Statistics, Test results missing