153
Control Accuracy
Parameter | Range |
|
| Accuracy |
|
|
IPAP | 4 to 501 cm H2O2 | Greater of 2 cm H2O or 8% of setting | ||||
|
|
| ||||
EPAP | 0 to 25 cm H2O for Active Circuits | Greater of 2 cm H2O or 8% of setting | ||||
| 4 to 25 cm H2O for Passive Circuits |
|
|
| ||
CPAP | 4 to 20 cm H2O | Greater of 2 cm H2O or 8% of setting | ||||
PEEP | 0 to 25 cm H | 2 | O for Active Circuits | Greater of 2 cm H | 2 | O or 8% of setting4 |
| 4 to 25 cm H2O for Passive Circuits |
|
|
| ||
Pressure | 4 to 50 cm H2O | Greater of 2 cm H2O or 8% of setting | ||||
Pressure Support | 0 to 30 cm H | 2 | O3 | Greater of 2 cm H | 2 | O or 8% of setting4 |
Tidal Volume | 50 to 2000 ml5 | Greater of 15ml or 10% of setting (Active | ||||
|
|
|
| Circuits) |
|
|
|
|
|
| Greater of 15ml or 15% of setting (Passive | ||
|
|
|
| Circuits) |
|
|
Breath Rate | 0 to 60 BPM for AC mode | Greater of ± 1 BPM or ±10% of the setting | ||||
| 1 to 60 BPM for all other modes |
|
|
| ||
Timed Inspiration | 0.3 to 5.0 seconds | ± .1 second |
|
| ||
|
|
|
|
| ||
Rise Time | 1 to 66 |
|
| ±2 cm H2O (the device will increase to a | ||
|
|
|
| pressure of .67* (IPAP - EPAP) ±2 cm H2O @ the | ||
|
|
|
| set rise time multiplied by 100 ms for pressure | ||
|
|
|
| supports less than or equal to 25.) | ||
Ramp Start Pressure | 0 to 25 cm H2O for Active Circuits | 8% of setting + 2% Full Scale | ||||
| 4 to 25 cm H2O for Passive Circuits |
|
|
| ||
| 4 to 19 cm H2O in CPAP mode |
|
|
| ||
Ramp Length | Off, 5 to 45 minutes | ±2 minutes |
|
| ||
|
|
|
|
|
|
|
Flex | Off, 1 to 37 |
|
| N/A |
|
|
Flow Trigger Sensitivity | 1 to 9 l/min |
|
| N/A |
|
|
|
|
|
|
|
|
|
Flow Cycle | 10 to 90% |
|
| N/A |
|
|
|
|
|
|
| ||
Apnea Rate | 4 to 60 BPM |
|
| Greater of 1 BPM or 10% of setting | ||
|
|
|
|
|
|
|
Specifications listed are based on using a standard circuit consisting of 1.8 meter tubing- REF 622038, one of the following exhalation devices: Whisper Swivel II - REF 332113; Active PAP Exhalation Device - REF 1053716; Active Flow Exhalation Device - REF 1049503 or Active Exhalation Device – REF 1065658; UPB Active PAP Exhalation Device - REF 1073862 and
Trilogy Proximal Flow Sensor- REF 1050408 (if required).
1Limited to 25 cm H2O when using the
2Pressure units may be cm H2O, hPa, or mBar depending on device setup.
3The difference between the Inspiratory Pressure and the Expiratory Pressure must never be more than 30 cm H2O.
4Pressure Support and PEEP not to exceed 50 cm H2O.
5All flows and volumes are measured at BTPS conditions.
6The range of values correspond to tenths of seconds (e.g., a setting of 4 indicates a Rise Time of 0.4 seconds).
7Flex is not available when AVAPS is active. Flex is not available with Active Circuits.
Chapter 11 Technical Specifications
