Ricoh IS300e Take out the scanner main unit, Optimum Environment Conditions, Power Connection

QUICK INSTALLATION GUIDE

Image Scanner

Please read the Safety Information in the Operating Instructions before using this machine. It contains important information related to USER SAFETY and PREVENTING MACHINE PROBLEMS.

UNPACKING THE SCANER AND CHECKING THE CONTENTS OF THE BOX

INSTALLING THE SCANNER

CAUTION

Attaching the Control Panel Unit to the Scanner Unit

Check the contents of the box according to the follow- ing list. If one some items are missing, please contact your sales or service representative.

Quick Installation Guide(this sheet)

CD-ROM

USB Interface Card

USB Cable

Power Cord

Tools

Control Panel Unit

Screw

Safety Instruction Sheet

Card slot cover

Ferrite Core (Europe only)

Remove the plastic bag. Lift the scanner and move it to the place where you want to install it.

•This product weighs approximately 29kg.

•To left this product, hold the grip at the center of both sides with 2 people and lift slowly not to inflict too much burden on the carriers body. Forcing yourself too much to lift or handling this product reck- lessly may lead to injury.

Take out the scanner main unit.

Note

❒Use the tool that comes with this machine when you tighten or loosen he screws.

Insert the plug of the control panel unit into the con- nector of the scanner unit, as illustrated below.

WHERE TO PUT THE SCANNER

The Scanner's location should be carefully chosen because environmental conditions greatly affect its performance.

WARNING

•Confirm that the wall outlet is near the machine and freely acces- sible, so that in event of an emergency, it can be unplugged easily.

•Only connect the machine to the power source described on this sheet.

•Avoid multi-wiring.

•Do not damage, break or make any modifications to the power cord. Do not place heavy object on it, pull it hard or bend it more than necessary. These actions could cause an electric shock or fire.

CAUTION

•Keep the machine away from humidity and dust. A Fire or an electric shock might occur.

•Place the machine on a strong and level surface. Otherwise, the machine might fall and cause personal injury.

•If you use the machine in a confined space, confirm that there is a continuous flow of air.

Optimum Environment Conditions

Recommended temperature and humidity

%RH	10 C 80%		27 C 80%
80
	15 C		25 C		32 C
	70%		70%
60					54%
40	15 C		25 C
	30%		30%
20	10 C 15%		32 C 15%
10		20	30		C
%RH	50 F80%		80.6 F 80%
80
	59 F		77 F		89.6 F
	70%		70%
60					54%
40	59 F		77 F
	30%		30%
20	50 F 15%		89.6 F 15%
50	60	70	80	90	F

Possible operation range Recommended range

The machine must be level within 5 mm,0.2" both front to rear and left to right.

TDLH140E

Environments to Avoid

Important

❒Locations exposed to direct sunlight or strong light

❒Dusty areas

❒Areas with corrosive gases

❒Areas excessively cold, hot, or humid

❒Locations near an air conditioner or humidifier

❒Locations near other electronic equipment

❒Locations where the scanner might be subjected to frequent strong vibration

Power Connection

Connect the power cord to a power source with the following specifications:

Product Specifications

North America	G421-17 power supply rating:
	AC 120V, 60Hz, 2A
Europe/Asia	G421-27 power supply rating:
	AC 220-240V, 50/60Hz, 1A
Electrical Outlet Requirements
North America	G421-17 Electrical Outlet Requirements:
	AC 120V, 60Hz, min.10A
Europe/Asia	G421-27 Electrical Outlet Requirements:
	AC 220-240V, 50/60Hz, min.5A

Space Required for Installing the Scanner

Leave enough space around the scanner. This space is necessary to operate the scanner. The recommended(or minimum)space requirement is as follows.

100mm

or more

ZDLH330

660mm

or more

ZDLH340

ZDLH200E

Remove the tape ( through ).

ZDLH206E

Open the automatic document feeder(ADF) and remove the protective sheet on the exposure glass.

ZDLH025E

DISENGAGING THE LOCK

Set the lock switch on left side of the scanner to the "Unlock" position.

ZDLH215E

ABK011S

Important

❒While making sure that the plug is facing in the correct direction, inset the plug as far as it goes into the socket. It may be a bit tight to insert the plug into the socket, so push the plug with a strength that is enough for inserting it in place.

Note

❒To avoid the plug being inserted in the wrong direction, the connector has a number of tiny prongs inside and outside of it. When you insert the plug into the connector, make sure that the connector is facing in the correct direction. Inserting in the wrong direction creates the risk of damage to the plug and the connector.

❒Be careful not to pinch the cable when you attach the control panel unit to the scanner unit.

❒Locating the scanner unit at an end of a desk makes it easy to attach the control panel unit.

Insert the hooks of the control panel unit to the scan- ner unit.

ZDLp330

Secure the control panel unit using the screw that comes with this machine.

ZDLp340

Note

❒Do not open the cover located at the lower left of the control panel. Changing configuration of the switches inside of the cover could cause this machine to stop operating normally.

G421-8600