Pr.36, Pr.37 | Delta Electronics VFD-M instruction

Chapter 4 Parameters

Allowable Max. Power Loss Time

Allowable Max. power loss time

Input

Pr.33

Pr.33

Power

speed synchronization

Output

Pr.32=1

detection

Pr.32=2

Speed search starts with

Speed search starts with

Power

the Master Frequency

minimum output frequency

Output

Baseblock

Baseblock

Voltage

Time

Time

Pr.34

Pr.34

speed search

Pr.36

Upper Bound of Output Frequency

Unit: 0.1Hz

Settings

0.10 Hz to 400.0 Hz

Factory Setting: 400

The Upper/Lower Bounds help prevent operation error and machine damage.

If the Upper Bound of Output Frequency is 50Hz and the Maximum Output Frequency is 60Hz, the Maximum Output Frequency will be limited to 50Hz.

Setting of this parameter must be equal to or greater than the Lower Bound of Output Frequency (Pr.37).

	Pr.37	Lower Bound of Output Frequency	Unit: 0.1Hz
		Settings 0.00 Hz to 400.0 Hz	Factory Setting: 0 Hz

Setting of this parameter must be equal to or less than the Upper Bound of Output Frequency If the Lower Bound of Output Frequency is 10Hz, and the Minimum Output Frequency (Pr.08) is set at 1.0Hz, then any command frequency between 1-10Hz will generate a 10Hz output from the drive.

output frequency

Pr.36

Pr.37

Input Freq.

Revision May 2008, ME14, SW V3.04

4-31

Image 66

Delta Electronics VFD-M manual Pr.36, Pr.37

Contents

Page Page Page Preface Page Table of Contents Troubleshooting Keypad and Start UpParameters Fault Code Information and Maintenance Appendix a Specifications Appendix B Accessories Appendix C How to Select the Right AC Motor Drive Introduction Model Explanation Receiving and InspectionNameplate Information Series Number Explanation D007M23A0 T 5 External Parts and Labels Remove Instructions Remove Keypad Remove Front Cover RST Side UVW Side Preparation for Installation and Wiring Ambient Conditions Minimum Mounting Clearances 50 mm 150mm Dimensions Model Name This page intentionally left blank Installation and Wiring Basic Wiring Diagram L1 NFB Excellent Good Not allowed External Wiring Appendix a Main Circuit Main Circuit Connection Terminal SymbolMains power terminals R/L1, S/L2, T/L3 Explanation of Terminal Function Terminals B1, B2 for connecting external brake unit Output terminals for main circuit U, V, W Main Circuit Terminals AWG Control Terminal Wiring Factory Settings RA-RCRB-RC AFM AVIACI M0~M5-GND Analog inputs AVI, ACI MO1MCM Digital outputs MO1 General Keypad and Start Up Keypad Description of the Digital Keypad How to Operate the Digital Keypad LC-M02E Displayed Message LC-M02E LED Keypad and Start Up Operation Method Trial Run Check following items Parameters Summary of Parameter Settings Parameter Explanation Settings FactorySetting Parameter Explanation Settings Factory Reset 00 M0 FWD/STOP, M1 REV/STOP01 M0 RUN/STOP, M1 REV/FWD Second Source for Frequency Command FLA Parameter Explanation Settings Factory CFA PLC FWD/REV Only Input positive PID feedback, PV from AVI Parameter Explanation Settings Factory Parameter Explanation Settings Factory Parameter Settings for Applications DC Braking before Running Applications Purpose FunctionsMulti-step Operation Applications Purpose Functions Operation Command Applications Purpose Two-wire/three-wire Applications PurposeWire Overheat Warning Applications Purpose Parameters Parameters Parameters Parameters Pr.01 Description of Parameter SettingsPr.00 Source of Frequency Command Pr.02 Stop Method Pr.03 Pr.04 Pr.08 Pr.06Pr.07 Pr.09 Commonly used V/F Setting General Purpose Pr.12 Pr.10Pr.11 Pr.13 Pr.14 Pr.15Pr.16 Pr.19 Pr.17Pr.18 Pr.20 Pr.24 Reverse Operation Inhibition Pr.26 Pr.27 Pr.28 Pr.29 Pr.30Pr.31 Pr.33 Pr.34Pr.35 Pr.36 Pr.37 Pr.38 Explanations Pr.40 Settings Function DescriptionPr.39 Pr.42 Settings Function Description GND First or Second Mx Close Run PLC Parameter value 18 programs Multi-Function Input Terminal Contact N.C. is reverse, once this function is set Pr.43 Analog Output Signal Pr.44 Pr.45 Pr.46 MO1 Pr.48 Pr.51 Potentiometer Reverse Motion EnablePr.47 Pr.49 Example Max Output Pr.03 Freq 60Hz Bias 10Hz Pr = FWD Pr.54 Pr.52Pr.53 Pr.55 Pr.58 Pr.59 Pr.62 Pr.60Pr.61 Pr.64 Pr.65 Pr.66 Pr.69 Pr.67Pr.68 Pr.70 Pr.73 Present Fault Record Pr.74 Pr.75 Third Most Recent Fault Record Pr.76 Parameter Lock and Configuration Pr.78 PLC Operation ModePr.77 Program input off and then back on Example 2 Pr.78 = 02 Continuously executes program cycles Example 3 Pr.78 = 03 Execute one cycle step by step REV Weights =Forward =Reverse Bit Application Note Pr.82 Pr.80Pr.81 Pr.83 Pr.89 Transmission Speed Baud rate Pr.92 Communication ProtocolComputer Control +15V 2 GND SG- 4 SG+ 6 for communication Data Format Ascii mode Communication Protocol ADR RTU modeStart END 6FH STX ADRLRC CHK F7H ‘6’ Starting data address ‘0’ ‘1’ B2H 0FHA0H CDH Starting address 21H 02H Read at one time CPU or analog circuit failure cF3 Parameters Void main Int OutportbPORT+MCR,0x08 Pr.93 Accel 1 to Accel 2 Frequency Transition Pr.94 Pr.95Pr.96 Pr.99 Pr.97Pr.98 Pr.100 Pr.103 Auto Tune Motor parameters Pr.104 R1 Value Pr.107 Pr.105 Control ModePr.106 Pr.108 Pr.112 Pr.113Cooling Fan Control PID Feedback Terminal Selection Integral Time Factory Setting 100 % PID Offset Level Settings To 50.0 % Inverts Reference Signal 0-20mA Wake Up Frequency Unit 0.10Hz Settings 00 to 400.0 Hz External Up/Down Selection Save Parameters Pr.155 Pr.157 Communication Mode SelectionReserved Pr.156 Parameters This page intentionally left blank Troubleshooting Over Current OC Ground Fault Over Voltage OV Low Voltage Lv Over Heat OH1 Overload Phase Loss PHL Keypad Display is Abnormal Motor cannot Run Motor Speed cannot be Changed Motor Stalls during Acceleration Motor does not Run as Expected Electromagnetic/Induction Noise Environmental Condition Serial reactor Phase lead capacitor Affecting Other Machines Fault Code Information Common Problems and SolutionsFault Name Fault Descriptions Fault Name Fault Descriptions Corrective Actions Fault Name Fault Descriptions Fault Name Fault Descriptions Reset Maintenance and Inspections Voltage Maintenance Check Items Methods and Criterion Keypad Maintenance Check Items Methods and Criterion Main circuit Maintenance Check Items Methods and CriterionChange of copper plate One One Daily Voltage Class 115V Class230V Class General Specifications 460V Class575V Class Analog Output Signal Analog frequency/current signal output This page intentionally left blank Appendix B Accessories All Brake Resistors & Brake Units Used in AC Motor Drives Appendix B Accessories Dimensions and Weights for Brake Resistors& Brake Units Dimensions are in millimeter Appendix B Accessories Non-fuse Circuit Breaker Chart Fuse Specification Chart AC Reactor AC Input Reactor Recommended Value AC Output Reactor Recommended Value Applications Mains circuit Zero Phase Reactor RF220X00A Diagram aDiagram B Remote Controller RC-01 VFD-M Programming PU06 Description of the Digital Keypad VFD-PU06 Explanation of Display Message Operation Flow Chart XX-XX AMD EMI Filter Cross Reference 40TDS4W4B16TDT1W4S Choose suitable motor cable and precautions Length of motor cable EMI Filter RF015M21AA / RF022M43AA Appendix B Accessories Din Rail Din Rail-DR01 Adapter Din Rail-DR02 Adapter Appendix C How to Select the Right AC Motor Drive Related Specification When one AC motor drive operates one motor When one AC motor drive operates more than one motorCapacity Formulas ⋅ IM ≤ the rated current of AC motor drive a General Precaution Parameter Settings NoteSelection Note How to Choose a Suitable Motor Standard motor Special motors 、 Pole-changing Dahlander motor Power Transmission Mechanism Motor torque This page intentionally left blank