DigiTech C0408 system manual Station C.O.S. Programming, Station COS Menu Selection

IMI 66-083 System Programming ,

•Selection 2: Line group assignment (assigns line to line groups, will be reserved if the hybrii strap is not installed)

•Selection 3: Line dialing mode (pulse or tone to match the connected line)

•Selection 4: Line privacy release (releases privacy on a line)

0 Selectlon 5: Line toll restriction table assignment

•Selection 6: Line abandoned hold release time

•Selection 7: Set up a line (Using a model line) (provides a means of programming a group of lines to match the programming of a model line)

•Selection 8: Assign name to line.

•Selection 9: Assign line to department.

•Selectlon 10: Exclusive hold.

•Selection 11: Voice mail line ID (Specifies identification number of a particular line to the voice mail accessory for personalized call coverage)

•Selection 12: DISD assignment (Assigns DISD to lines and specifies calling characteristics of them)

Station C.O.S. Programming

1.Set Up a Station (Using a Model Station)

2.Assign Name to Station

3.Assign Station to Department

4.Assign Station to SOHVA Group

5.Line/ Intercom Features

6. Ringing Assignment

7.Button Mapping

8.Toll Restriction Administration

9.Automatic Busy/ RNA Call Forwarding

10.Miscellaneous Feature Programming

11.Return To Previous Menu

Enter Selection:

STATION COS MENU SELECTION

In each station COS menu selection, after choosing the feature, enter a station port number which is to be assigned to it and enter line port ‘numbers where . . .

prompted. Muttiple station number entries are allowed for some features as prompted.

•Selectlon 1: Set up a station (Using a model station) (program a group of stations to match the programming of a model station)

•Selectlon 2: Assign name to station

•Selection 3: Assign station to department

•Selectlon 4: Assign station to SOHVA groups

0 Selectlon 5: Line/Intercom features

•Prime Line (assign prime line, prime group, prime intercom, or clear all)

. Ringing Line Preference (enable or disable)

•Line Access Deny (enable or disable station access to a line)

•Line Originate Deny (enable or disable station ability to originate a call on a line)

•Idle Line Preference (enable or disable access to an idle line when station is taken off hook)

•Block Voice Announce Intercom Call

•Audible Monitoring (audible ringing sounded for stations with BLF appearance at programmed station)

•Selection 6: Ringing assignment

•Personal Ringing Tones (One of four different tones can be chosen. Refer to page 4-29 for frequencies if required.)

•Direct/Delayed Ringing (of each line assigned to programmed station)

•Night Ringing (enable or disable night transfer, of ringing, to programmed station for programmed lines)

•SelectIon 7: Button mapping (assign functions to buttons)

Special Note: Affhough buttons are identified by Ax and Bx codes as shown in Figure 4-lon page 449 and on fhe programming overlay supplied with the system, do not type an *A”or “B” before the buffon number when identifying it for function assignment. To do so, causes the system to interpret the typed entry as a line number choice instead of a button number choice.

•Functions that can be assigned are identified per the following list:

To display list, enter ?.

Return to key mapping with Control 2. BLK . . . . . . . . . Blank

Line (1 - 24)

~?::::IStatiin (10 - 57) DND . . . . . . . . Do Not Disturb PRI . . . . . . . . . . Privacy

IC2 . . . . . . . . . . 2nd Intercom SAV . . . . . . . . . Save

ACC . . . . . . . . Account Code Button ZPX . . . . . . . . . Zone Page (l-3)

AC . . . . . . .;... All Call

ACB . . . . . . . . Auto Callback C F . . . . . . . . . . . Call Forward

4-89