Calibration
Resistor Value
Registers
The Calibration Resistor Value Registers store the value of the resistor used to calibrate current output. The Calibration resistor value is a
Address
Base + 18016
Bit | 15 | 14 | 13 | 12 | 11 | 10 | 09 | 08 | 07 | 06 | 05 | 04 | 03 | 02 | 01 | 00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
READ |
| 2nd Least Significant Byte |
|
|
| Least Significant Byte |
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WRITE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Address
Base + 18216
Bit | 15 | 14 | 13 | 12 | 11 | 10 | 09 | 08 | 07 | 06 | 05 | 04 | 03 | 02 | 01 | 00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
READ |
|
| Most Significant Byte |
|
|
| 2nd Most Significant Byte |
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WRITE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Value: The
Voltage Calibration Status Register
The Voltage Calibration Status Register provides a
Address | Bit | 15 | 14 | 13 | 12 | 11 | 10 | 09 | 08 | 07 | 06 | 05 | 04 | 03 | 02 | 01 | 00 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
READ | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | Ch | ||
Base + 18416 | ||||||||||||||||||
| 16 | 15 | 14 | 13 | 12 | 11 | 10 | 09 | 08 | 07 | 06 | 05 | 04 | 03 | 02 | 01 | ||
| WRITE | |||||||||||||||||
| Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | Volt | ||
|
| Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | Cal | |
|
| Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | Stat | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ch XX Cal Stat: This field is set to a one (1) when the channel has been successfully voltage calibrated. This field is set to a zero (0) when the channel is not voltage calibrated.
Notes This register is not set or used by the hardware. The HP E1418A SCPI driver, if used to calibrate the module, automatically sets the bits in this register. If you use register programming to calibrate this module, you may wish to use this register to record the calibration status.
The Voltage Calibration Status Register, the Current Calibration Status Register, the Calibration Isolation Status Register, and the Calibration Card Configuration Register are used together to store the overall calibration status of the module.
144 HP E1418A | Appendix B |
